8/12/2019 Formulario Solicitud Spiral Trac Adaptador
1/2
Order Form - Adaptor
Equipment Information:
Flush Rate:
Make:
Model:
Size:
Product:
%Solids:
Temperature:
Distributor Information:
Company:
Specialist:
P.O.#
Customer Information:
Company:
Customer Name:
Signature:
B(Box ID) =A(Sleeve OD) =
L(Gasket Option) =
G(Nose Length) =
CCWCWShaft rotation as viewed from the motor end: LRInch MetricUnits of measurement:
Gasketing Surface
Option:
C(Flange OD) = D(Seal Cavity Depth) =
E(Flange Length) =
FOR ALL CONFIGURATIONS: Sufficient flush pressure to drive a positive flow
into the box is required.
Vertical applications sized the same as horizontal EnviroSeal recommends that a flow meter and
check valve be utilized on the flush line.
416
316 Split
SolidMaterial: ESC(Carbon Graphite PTFE)
BRZ
Other
Qty:
#1 #2 #3 #4 #5 #6 #7
E
C
A
G
D FO
B
Mechanical packing being used:
Size:
Model:
FO(First Obstruction) =
SpiralTracTM
AVAILABLE WORLDWIDE
1310 Rocky Lake Drive, Waverley
Nova Scotia, Canada B2R 1R6
Tel (902) 861-3464 Fax (902) 861-3522
Website http://www.enviroseal.ca
The information contained in this bulletin is accurate attime of print. The purchaser is responsible for ensuring thedimensions, quantity and applications suitability meetend-user requirements. Most products are "manufacturedto order"; therefore, EnviroSeal Engineering Products Ltd.retains the right to individually authorize returns basedupon the potential for resale of the products within a
reasonable period of time.
L
Gasket Groove
Note:Min 0.625" if split device
J (Bolt Size) =H(To edge of flush port) = I(Bolt Pattern / Diameter) =
K= Packing size desired
E
C II A
G
H
D FO
B
L
Mechanical seal being used:
Make:
Model:
K
JJ
Option #7
8/12/2019 Formulario Solicitud Spiral Trac Adaptador
2/2
A F S R2001
Adaptor Part Number Code
AVAILABLE WORLDWIDE
Easy Installation Options
Option 3
Has a pre-machined gasketing surface
Extended nose piece fills the seal cavity and allows
the particulate to be expelled at the throat
Removes Particulate from around the seal faces
Requires Minimal Flush
Option 4
Option 6
No Flange. Used to fill large cross-section of
big-bore box allowing for standard seal installation
Removes particulate from around the seal faces
Fills the seal cavity and allows the particulate tobe expelled at the throat
Requires Minimal Flush
Option 2
Has a pre-machined gasketing surface
Longer flange to allow the seal to be moved away
from any worn areas on the shaft
Removes Particulate from around the seal faces
Requires Minimal Flush
Option 1 Standard Configuration Has a pre-machined gasketing surface
Pre-machined groove for optionalO-Ring
Removes Particulate from around the seal faces.
Requires Minimal Flush
Option 5 Has a pre-machined gasketing surface
Extended nose piece fills the seal cavity and allows
the particulate to be expelled at the throat
Extended front chamber to allow for cartridge seals
Removes Particulate from around the seal faces
Requires Minimal Flush
Note 2
Note 2
Note 2
Note 2
Note 2
Note 2
Note: 1. For no flush applications please contact EnviroSeal
2. Also available with pre-machined gasket groove
The information contained in this bulletin is accurate at timeof print. The purchaser is responsible for ensuring thedimensions, quantity and applications suitability meetend-user requirements. Most products are "manufactured toorder"; therefore, EnviroSeal Engineering Products Ltd.retains the right to individually authorize returns based uponthe potential for resale of the products within a reasonableperiod of time.
1310 Rocky Lake Drive, Waverley
Nova Scotia, Canada B2R 1R6Tel (902) 861-3464 Fax (902) 861-3522Toll Free North America Only 1-800-884-7325Website http://www.enviroseal.ca
SpiralTracAdaptor F
Flush RequiredSSplit Non-Split
NNote 1
or R LorDrawing NumberSince each device is uniquein regards to sizing, all of this
information is includedon the drawing.
ST01485-230502 Rev A
Option 7
Has a pre-machined gasketing surface
For use with packing
Moves the packing down the shaft
to an area with less wear,there-by prolonging
the life of the shaft / sleeve
Requires Minimal Flush
Has a pre-machined gasketing surface
Extended nose piece fills the seal cavity and allows
the particulate to be expelled at the throat
Removes Particulate from around the seal faces
Two piece design to avoid first obstruction issues
Requires Minimal Flush
Shaft Rotation
as viewed from
Motor End
ESC- PTFE
316 - 316 SS
416 - 416 SS
BRZ - Bronze
ESC
Material