8/12/2019 Formulario Solicitud Spiral Trac Adaptador

1/2

Order Form - Adaptor

Equipment Information:

Flush Rate:

Make:

Model:

Size:

Product:

%Solids:

Temperature:

Distributor Information:

Company:

Specialist:

P.O.#

Customer Information:

Company:

Customer Name:

Signature:

B(Box ID) =A(Sleeve OD) =

L(Gasket Option) =

G(Nose Length) =

CCWCWShaft rotation as viewed from the motor end: LRInch MetricUnits of measurement:

Gasketing Surface

Option:

C(Flange OD) = D(Seal Cavity Depth) =

E(Flange Length) =

FOR ALL CONFIGURATIONS: Sufficient flush pressure to drive a positive flow

into the box is required.

Vertical applications sized the same as horizontal EnviroSeal recommends that a flow meter and

check valve be utilized on the flush line.

416

316 Split

SolidMaterial: ESC(Carbon Graphite PTFE)

BRZ

Other

Qty:

#1 #2 #3 #4 #5 #6 #7

E

C

A

G

D FO

B

Mechanical packing being used:

Size:

Model:

FO(First Obstruction) =

SpiralTracTM

AVAILABLE WORLDWIDE

1310 Rocky Lake Drive, Waverley

Nova Scotia, Canada B2R 1R6

Tel (902) 861-3464 Fax (902) 861-3522

Website http://www.enviroseal.ca

The information contained in this bulletin is accurate attime of print. The purchaser is responsible for ensuring thedimensions, quantity and applications suitability meetend-user requirements. Most products are "manufacturedto order"; therefore, EnviroSeal Engineering Products Ltd.retains the right to individually authorize returns basedupon the potential for resale of the products within a

reasonable period of time.

L

Gasket Groove

Note:Min 0.625" if split device

J (Bolt Size) =H(To edge of flush port) = I(Bolt Pattern / Diameter) =

K= Packing size desired

E

C II A

G

H

D FO

B

L

Mechanical seal being used:

Make:

Model:

K

JJ

Option #7

8/12/2019 Formulario Solicitud Spiral Trac Adaptador

2/2

A F S R2001

Adaptor Part Number Code

AVAILABLE WORLDWIDE

Easy Installation Options

Option 3

Has a pre-machined gasketing surface

Extended nose piece fills the seal cavity and allows

the particulate to be expelled at the throat

Removes Particulate from around the seal faces

Requires Minimal Flush

Option 4

Option 6

No Flange. Used to fill large cross-section of

big-bore box allowing for standard seal installation

Removes particulate from around the seal faces

Fills the seal cavity and allows the particulate tobe expelled at the throat

Requires Minimal Flush

Option 2

Has a pre-machined gasketing surface

Longer flange to allow the seal to be moved away

from any worn areas on the shaft

Removes Particulate from around the seal faces

Requires Minimal Flush

Option 1 Standard Configuration Has a pre-machined gasketing surface

Pre-machined groove for optionalO-Ring

Removes Particulate from around the seal faces.

Requires Minimal Flush

Option 5 Has a pre-machined gasketing surface

Extended nose piece fills the seal cavity and allows

the particulate to be expelled at the throat

Extended front chamber to allow for cartridge seals

Removes Particulate from around the seal faces

Requires Minimal Flush

Note 2

Note 2

Note 2

Note 2

Note 2

Note 2

Note: 1. For no flush applications please contact EnviroSeal

2. Also available with pre-machined gasket groove

The information contained in this bulletin is accurate at timeof print. The purchaser is responsible for ensuring thedimensions, quantity and applications suitability meetend-user requirements. Most products are "manufactured toorder"; therefore, EnviroSeal Engineering Products Ltd.retains the right to individually authorize returns based uponthe potential for resale of the products within a reasonableperiod of time.

1310 Rocky Lake Drive, Waverley

Nova Scotia, Canada B2R 1R6Tel (902) 861-3464 Fax (902) 861-3522Toll Free North America Only 1-800-884-7325Website http://www.enviroseal.ca

SpiralTracAdaptor F

Flush RequiredSSplit Non-Split

NNote 1

or R LorDrawing NumberSince each device is uniquein regards to sizing, all of this

information is includedon the drawing.

ST01485-230502 Rev A

Option 7

Has a pre-machined gasketing surface

For use with packing

Moves the packing down the shaft

to an area with less wear,there-by prolonging

the life of the shaft / sleeve

Requires Minimal Flush

Has a pre-machined gasketing surface

Extended nose piece fills the seal cavity and allows

the particulate to be expelled at the throat

Removes Particulate from around the seal faces

Two piece design to avoid first obstruction issues

Requires Minimal Flush

Shaft Rotation

as viewed from

Motor End

ESC- PTFE

316 - 316 SS

416 - 416 SS

BRZ - Bronze

ESC

Material