5 Service Manual - LG -Lw20

8/8/2019 5 Service Manual - LG -Lw20

1/88

www.SoporteTecnicoBsAs.com.ar

Repuestos para tus equipos.

Al mejor precio.

Envios a Todo el Pais
http://www.soportetecnicobsas.com.ar/http://www.soportetecnicobsas.com.ar/http://www.soportetecnicobsas.com.ar/http://www.soportetecnicobsas.com.ar/http://www.soportetecnicobsas.com.ar/


2/88

0

Service Manual

(LW20)

LG Electronics


3/88

1

Ch 1. Service information

Ch 2. Locations

Ch 3. System information

Specification

Model configuration

System Block Diagram

Fn key combinations

Status indicators

BIOS Flash

BIOS Setup

Ch 4. Symptom-to-part index

Power system checkout

Numeric error codes

Error messages

LCD-related symptoms

Indeterminate problems

Ch 5. Removing and replacing a part (FRU)

Ch 6. Part list

Part list

Exploded view

Contents


4/88

2

Chapter 1. Service information

1-1. Important service information

Strategy for replacing parts (FRU-Field Replaceable Units)

Before replacing parts

Make sure that latest BIOS and drivers are installed before replacing any parts (FRUs) listed in this

Caution

The BIOS configuration on the computer you are servicing may have been customized.

Running Automatic Configuration my alter the settings. Note the current configuration settings;then, when service has been completed, verify that those settings remain in effect.

Strategy for replacing a hard-disk drive

You have to get a Users approval before formatting or replacing a hard-disk drive. You must let the User

know that the user is responsible for the loss data

Caution

The drive startup sequence in the computer you are servicing may have been changed. Be

extremely careful during write operations such as copying, saving, or formatting. If you select an

incorrect drive, data or programs can be overwritten.

Use the following strategy to prevent unnecessary expense for replacing and servicing parts

1. If you are instructed to replacing a part but the replacement does not correct the problem, reinstall the

original part before you continue.

2. Some computers have both a processor board and system board. If you are instructed to replace either

the processor board or the system board, and replacing one of them does not correct the problem,

reinstall that board, and then replace the other one.

3. If an adapter or device consists of more than one part, any of the parts (FRUs) may be the cause of the

error. Before replacing the adapter or device, remove the parts (FRUs), one by one, to see if the

symptoms change. Replace only the part that changed the symptoms.

Ch1. Service information


5/88

3

1-2. Safety notices

Warning

Before the computer is powered-on after part (FRU) replacement, make sure all screws, springs,

and other small parts are in place and are not left loose inside the computer. Verify this by

shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause

electrical shorts.

Warning

some standby batteries contain a small amount of nickel and cadmium. Do not disassemble

a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery

as required by local ordinances or regulations. Use only the battery in the appropriate parts

listing. Use of an incorrect battery can result in ignition or explosion of the battery

Warning

The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or

water, or short-circuit it. Dispose of the battery pack as required by local ordinances or

regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.

Use of an incorrect battery can result in ignition or explosion of the battery.

Warning

If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands,immediately was the affected areas with water for at least 15 minutes. Seek medical care if any

symptoms from the fluid are present after washing.

Warning

To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card.

Warning

Though the main batteries have low voltage, a shorted or grounded battery can produce enough

current to burn personnel or combustible materials.

Warning

Before removing any part (FRU), turn off the computer, unplug all power cords from electrical

outlets, remove the battery pack, and then disconnect any interconnecting cables.



6/88

4

1-3. Safety information

General safety

Follow these rules to ensure general safety

Observe good housekeeping in the area of the machines during and after maintenance.

When lifting any heavy object

1. Ensure you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.

4. Lift by standing or by pushing up with your leg muscles

(This action removes the strain from the muscles in your back.)

Do not attempt to lift any object weights more then 16kg(35lb) or object that you think are too heavy for you.

Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.

Before you start the machine, ensure that other service representatives and the customers personnel are

not in a hazardous position.

Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the

machine.

Keep your tool box away from walk areas so that other people will not trip over it.

Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your

sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately

8 centimeters(3 inches) from the end.

Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for you clothing.

Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using

solvents, or working in any other conditions that might be hazardous to your eyes.

After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that

is worn or defective.

Reinstall all covers correctly before returning the machine to the customer.

CautionMetal objects are good electrical conductors.



7/88

5

Electrical safety

Observe the following rules when working on electrical equipment.

Important

Use only approved tools and test equipment. Some hand tools have handles covered with a soft

material that does not insulate you when working with live electrical currents.

Many customers have, near their equipment, rubber floor mats that contain small conductive

fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from

electrical shock.

Find the room emergency power-off switch, disconnecting switch, or electrical outlet. If an electrical outlet.

If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

Do not work alone under hazardous conditions or near equipment that has hazardous voltages.

Disconnect all power before

1. Performing a mechanical inspection

2. Working near power supplies

3. Removing or installing main units

Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer

to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.

If you need to work on a machine that has exposed electrical circuits, observe the following precautions :

Ensure that another person, familiar with the power-off controls, is near you.

Caution

Another person must be there to switch off the power, if necessary.

Use only one hand when working with powered-on electrical equipment. Keep the other hand in your

pocket or behind your back

Caution

An electrical shock can occur only when there is a complete circuit. By observing the above rule,

you may prevent a current from through your body.

When using testers, set the controls correctly and use the approved probe leads and accessories for that

tester



8/88

6

Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal

floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages. These instructions are in

the safety sections of maintenance information. Use extreme care when measuring high voltages.

Regularly inspect and maintain your electrical hand tools for safe operational condition.

Do not use worn or broken tools and testers.

Never assume that power has been disconnected from a circuit. First check that it has been powered off.

Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,

non-grounded power extension cables, power surges, and missing safety grounds.

Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is

conductive such touching can cause personal injury and machine damage.

Do not service the following parts with the power on when they are removed from their normal operating

places in a machine.

1. Power supply units

2. Pumps

3. Blowers and fans

4. Motorgenerators

and similar units. (This practice ensure correct grounding of the units.)

If an electrical accident occurs

1. Use caution ; do not become a victim of yourself.

2. Switch off power.

3. Send another person to get medical aid.



9/88

7

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions.

As each machine was designed and built, required safety items were installed to protect users and service

personnel from injury. This guide addresses only those items. You should use good judgment to identify

potential safety hazards due to attachment of non-LG features or options not covered by this inspectionguide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and

whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present

1. Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal

electrical shock)

2. Mechanical hazards, such as loose or missing hardware

Refer to the following checklist and begin the checks with the power off, and the power cord disconnected.

Checklist

1. Check exterior covers for damage (loose, broken, or sharp edges)

2. Power off the computer. Disconnect the power cord.

3. Check the power cord for :

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity

for 0.1 or less between the external ground pin and frame ground.

b. The power cord should be the type specified in the parts list.

c. Insulation must not be frayed or worn.

4. Remove the cover.

5. Check for any obvious non-LG alterations. Use good judgment as to the safety of any non-LG

alterations.

6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or

other liquids, or signs of fire or smoke damage.

7. Check for worn, frayed, or pinched cables.

8. Check that the power-supply cover fasteners (screw or rivets) have not been removed or tampered with.



10/88

8

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to

electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between

objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat,

and the person handling the part are all at the same charge.

Note

Use product-specific ESD procedures when they exceed the requirements noted here.

Make sure that the ESD protective devices you use have been certified (ISO9000) as fully effective.

When handling ESD-sensitive parts :

1. Keep the parts in protective packages until they are inserted into the product.

2. Wear a grounded wrist strap against your skin to eliminate static on your body.

3. Prevent the part from touching your clothing. Most clothing retains a charge even when you are wearinga wrist strap.

4. Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially

useful when handling ESD-sensitive devices.

5. Select a grounding system, such as those listed below, to provide protection that meets the specific

service requirement.

Note

The use of a grounding system is desirable but not required to protect against ESD damage.

a. Attach the ESD ground clip too any frame ground, ground braid, or green-wire ground.

b. Use an ESD ground or reference point when working on a double-insulated or battery-operated

system. You can use coax or connector-outside shells on these systems.

c. Use the round ground-prong of the AC plug on AC-operated computers.


Grounding requirements

Electrical grounding of the computers is required for operator safety and correct system function.

Proper grounding of the electrical outlet can be verified by a certified electrician.


11/88

9

When a CD-ROM drive, DVD drive or the other laser product is installed, note the following :

Caution

Use of controls or adjustments or performance of procedures other than those specified here in

might result in hazardous radiation exposure.

1-4. Laser compliance statement

Opening the CD-ROM drive, DVD-ROM drive or the other optical storage device could result in exposure

to hazardous laser radiation.

There are no serviceable parts inside those drives. Do not open

Danger

Emits visible and invisible laser radiation when open. Do not stare into the beam , do not view

directly with optical instruments, and avoid direct exposure to the bean.

1-5. Backup (Standby) RTC battery safety information

When replacing or disposing of the backup (standby) RTC battery, note the following :



12/88

10

1-6. Read this first

Before you go to the checkout guide, be sure to read this section.

Important Notes

Only trained personnel certified by LG should service the computer.

Read the entire FRU removal and replacement page before replacing any FRU.

Use new nylon-coated screws when you replace FRUs.

Be extremely careful during such write operations as copying, saving, formatting.

Drives in the computer that you are servicing sequence might have been altered. If you selected an

incorrect drive, data or programs might be overwritten.

Replace FRUs only for the correct mode.

When you replace a FRU, make sure the model of the machine and the FRU part number are correct by

referring to the FRU parts list.

A FRU should not be replaced because of a single, irreproducible failure. Single failures can occur for a

variety of reasons that have nothing to do with a hard ware defect, such as cosmic radiation,

electrostatic discharge, or software errors.

Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the

error log and run the test again. If the error does not recur, do not replace the FRU.

Be careful not to replace a non-defective FRU.

What to do first

You must fill out the record form first.

During the warranty period, the customer may be responsible for repair costs if the computer damage was

caused by misuse, accident, modification, unsuitable physical or operating environment, or improper

maintenance by the customer. The following list provides some common items that are not covered under

warranty and some symptoms that might indicate that the system was subjected to stress beyond normal

use. Before checking problems with computer, determine whether the damage is covered under the

warranty by referring to the following :



13/88

11

The followings are not covered under warranty :

CD panel cracked from the application of excessive force or from being dropped

Scratched (cosmetic) parts

Distortion, deformation, or discoloration of the cosmetic parts

Cracked or broken plastic parts, broken latches, broken pins, or broken connectors caused by excessiveforce

Damage caused by liquid spilled into system

Damage caused by improper insertion of a PC Card or the installation of an incompatible card

Damage caused foreign material in the diskette drive

Diskette drive damage caused by pressure on the diskette drive cover or by the insertion of a diskette

with multiple labels

Damaged or bent diskette eject button

Fusses blown by attachment of a non-supported device

Forgotten computer password (making the computer unusable)

Sticky keys caused by spilling a liquid onto the keyboard

The following symptoms might indicate damage caused by non-warranted activities :

Missing parts might be a symptom of unauthorized service or modification.

If the spindle of a hard-disk drive becomes noisy, it may have been subjected to excessive force, or

dropped.



14/88

12

Chapter 2. Locations

Ch2. Locations

Front view

Rear view

Security key hole (Kensington Lock)

User can attach a separately purchased chain lock into the security keyhole and connect it to a fixed object

to prevent a notebook theft

LCD

Volume Down

Volume Up

Keyboard

Touchpad Button

MUTE Button

SRS Button

Touchpad

Internal SpeakerInternal Speaker 5-in-1 Card Slot

Power Button

Internal MIC

USB Connector

Security key hole

S-VIDEO Connector


15/88

13

Left view

Ch2. Locations

Right view

Emergency eject hole

Insert a thin and hard pin into this hole, and you can open the disc tray manually.

VGA Connector Fan Louver

MIC ConnectorIEEE 1394 Connector

USB Connector

Headphone Connector

Line-in Connector / SPDIF Connector

Optical Disk Drive

LAN Connector

ODD Eject Button

Emergency eject hole

AC Connector

ODD Open Button

Modem Connector


16/88

14

Specification

Chapter 3. System information

Ch3. System information

- CPU

Dothan 1.6 ~ 2.1 GHz

FCPGA

- Main Chipset & Graphic

Intel 915GM,ICH6-M

- Memory

2SODIMM Up to 2GB

DDR2 PC2-3200S/4200S Capable (400/533MHz)

- HDD

1.8" 5mm/8mm 30/40/60GB PATA Type

- Communication

MDC Modem, Daughter Card Type

Marvell Yukon 88E8053 PCI-E Gigabit Ethernet Controller

Marvell Yukon 88E8036 PCI-E 10/100 Ethernet Controller

- Wireless LAN Solution

802.11bg/abg Mini PCI Type, Hexa-band Antenna

- Card Slot

Express Card Slot

5-in-I Card Slot (XD Picture, Memory Stick, Memory Stick Pro, Multi Media Card, SD Card)

- ODD

Removable Optical Storage

DVD, DVD-COMBO, DVD Super Multi Optional DMB Support

- Port

VGA, 3X USB(2.0), RJ11, RJ45, Headphone, Line-in/SPDIF, Mic-in, AC-in, IEEE1394, S-Video

- Input Devices

Keyboard : 86Key Keyboard

Touchpad

- Buttons

Power, Volume Down, Volume Up, Mute, SRS

- Indicator (LED)

Power On, Charge, HDD, Caps Lock, Num Lock, Wireless- Power

65 Watt 18.5V 3.5A Adapter

- Audio

Realtek Azalia Audio Codec ALC880, Stereo speakers

- Battery

6 Cell 4.8AHr, CYLINDRICAL (Li-Ion)


17/88

15

page46

page13-15

page09

page38

page31

page18

page30

ACIN

3V

5V

HDD

SUBBD

page20

pag

e5

CK-SSCD

3.3V

page28

PORT3

3.3V

VCCP

VOLUMES/W

NUMLOCK

RJ45/RJ11

DDR2

3.3V

MI

C

PCIREQ/GNT0

3.

3V

5V

MDCMODEM

Powerrail&BatteryConn.

Wireless

DDR2400/533MHz

AM

P

SENSOR

page27

1.8V

page44

ALC880

S

-VIDEOCONN

SATA

SUBBD

PIRQC/D

5V

USB7

88E8036

DDR2

TV/CRT/LVDS

H8S2110B

V1.2S/V1.5A

FANC

ONN

SUBBOA

RD

page28

3.

3V

AUDIO pa

ge37

USB2

BAYCO

NN.

page42

ANALOGVCC(5V)

CK-410M

NEWCARD

HP/SPDIF

CODEC

DDR2DC/DC

DIGITAL(3.3V)

5V

page21-26

1394

page28

3V

page45

LPC3.3V,33MHz

USB3

1.0V

10/100

page45

PORT

page33

SUBBOARD

FWH

PORT1

3.3V

page6-12

AC97/AZALIA

GbE

SUBB/D

3.3V

SUBBD

PCI7411

GMCH_CORE

page31

page44

I

NT.KBD

NEWCARD

WI

NDRIVER

POWERS/W

THERMAL

page2-4

page19

page28

TOUCHPAD

PCIREQ/GNT3

SU

BBD

SYSTEMDC/DC

3.3V

page40

88E8052

SU

BBD

AD16

DOTHAN(NV)

SATATOPATA

USB2

page47

page34-36

page29

page30

SODIMM-0/1

ICH6-M

VCCP

PCI3.3V,33MHz

PIRQA,SERIRQ

PWRON

SUBB/D

5V U

SB5

HDD

SUBB/D

USB5

page5

Miscellaneous

BATTERYCHARGER

SUB

BOARD

4IN1

Magnetic

SUBB/D

3.3v

CAPSLOCK

GMCH_CORE(1.05V)

page48

ALVISO-GM

USB6

USB5

page20

page39

AD18

FSB533MHz

SUBBD

1.8V

CPU_CORE

EEPROM

PCIEXPRESS

CHG

PATA66/100

MINIPCICONN

SUBB/D

5V/3.3V

USB7

USBInterface

LCDCONN

1.5V

USB0/1

VCCP

SUBBOARD

USB0

3.3V

5V

page

SUBBOARD

USB6

3.3V

DMI

LEDs

CPUCOREVCC

SST49LF008A

USB0/1

CRTCONN

page27

USB3

System Block Diagram



18/88

16

Fn key combinations

The following table shows the function of each combination of Fn with a function key.

Function of Fn keys has nothing to do with Operating System.


PauseFn + PgDn

(Pause Break)

Print ScreenFn + PgUp (Prt

Sc Sys Rq)

Insert[Fn] + [Delete]

Num Lock[Fn] + Scr Lk

[Num Lk]

Brighten the LCD (8 Steps).[Fn] + End

Darken the LCD (8 Steps).[Fn] + Home

Maximum power-saving mode. (When OSD is installed.)[Fn] + [F12]

CPU Cooling Fan control mode (Normal / Slow / Fast).[Fn] + [F11]

System information.[Fn] + [F10]

LCD Auto Brightness control Enable/Disable.Enable/disable Auto Brightness control. (ON/OFF)

Refer to Battery Miser 2005 Help.

[Fn] + [F9]

Audio Enable/disable

Refer to Battery Miser 2005 Help.[Fn] + [F8]

Monitor toggle.When the computer is attached to an external monitor, you can change the display outputlocation with [Fn] + [F7] combination.

You can switch to and from the three types of display modes, LCD display only, the externalmonitor only, or both at the same time.

[Fn] + [F7]

Wireless LAN Enable/Disable Toggle.[Fn] + [F6]

Press the combination once to disable the touch pad, and press again to enable the touch pad.

(The touch pad initialization takes 1~2 seconds, so wait for the initialization to end before usingthe touch pad)

[Fn] + [F5]

Forces the computer to enter power-saving mode. (ex: system standby and hibernation)[Fn] + [F4]

User defined Hot key. (available from OSD Setting)[Fn] + [F3]




19/88

17

Status indicators


The system status indicators show the status of the computer

1. Num lock

Num lock indicator lights up when Num lock key is pressed.

By pressing Fn + Scr LK (Num LK) key, you can use the embedded numeric keys.

To disable the embedded numeric keys, press Fn + Scr LK (Num LK) key again.

- The Num Lock indicator is off while an external keyboard is connected if OSD keyboard setup is

configured not to use embedded keypad with an external keyboard connection.

2. Caps lock

Caps lock indicator lights up when the Caps lock key is pressed.

When this indicator lights up, you can type capital letters without pressing the Shift key.

3. Drive in use

Drive in use indicator lights up when data is being written to or read from the hard disk or optical disk

drive.

- Do not turn off the power when Drive in use indicator is on.

It may result in loss of data in the hard disk.

4. Wireless activity indicator

Off: Wireless LAN is not in use.

Blinking(3-4 Seconds): Searching for Access point for Wireless LAN Connection.

Blinking (short interval): Data is transferring with Wireless LAN is on.

5. Power

Power status indicator indicates the following status of the computer.

Off: The computer is turned off or is in hibernation mode.

On: The computer is turned on.

Blinking: The computer is in standby mode.

6. Battery status indicator

Orange light: Battery is being charged.

Orange light/ Blinking (Green): Battery is being charged - battery is remaining more than 90% of its

maximum capacity.

Off: Battery is being discharged.

Green: Battery is fully charged or empty while the AC adapter is connected.

Blinking (Green): Battery is remaining less than 10%, or being discharged.

Blinking (Red): A battery error occurs.

- The Battery indicator blinks as you have set the alarm action from the Battery miser 2005.


20/88

18

BIOS Flash

You can update BIOS using a floppy disk drive.

Because this system is not equipped with any floppy disk drive, you have to use an external USB drive for

a BIOS update. In order to boot up with an USB drive, please set Removable Device as the first boot up

drive in the boot menu of BIOS setup.

How to update flash ROM in DOS

1. Create boot up flash update diskette.

2. Copy a ROM image file (*.wph) into the root of the flash update diskette.

3. Copy phlash16.exe to the flash update diskette.

4. Insert the diskette into the FDD of your computer.

5. Boot your computer with the diskette, and type phlash16*.wph /mode=n.

6. Cold boot and follow the instruction displayed on the screen.

Flash options /mode=n

0 Default mode. Keep the current DMI information and update BIOS image only.

1 Update DMI information only.

If new DMI information is not specified, the current DMI information is left unchanged.

2 Update BIOS and DMI information.

If new DMI information is not specified, the current DMI information is left unchanged.

3 Update BIOS and DMI information.

DMI information is updated to the DMI string and options specified in the new BIOS image.

Note

DMI is Desktop Management Interface



21/88

19

BIOS Setup

BIOS (Basic Input and Output System) Setup saves the system configuration in CMOS RAM, and

check the configurations during startup. Use the BIOS Setup Utility to change and save the system

environment, hardware configurations, power saving mode, etc.

Open the BIOS Setup Utility in the following situations :

1. to change the BIOS setup

2. to replace the backup battery

3. system configuration error occurs

4. to change the boot order

5. to set/change a password

Press the power button.

When the LG logo appears on the screen, press and enter theBIOS Setup Utility.



22/88

20

Using the keys

The keys used in the BIOS Setup Utility and their functions are described at the bottom.

, + : General Help

Display the descriptions of the keys used in the setup utility.

, : Select Item

Navigate and select items in the setup utility. The selected item becomes highlighted.

, : Select Menu

Move to another menu.

/ , : Change Values

Change the value of a selected item.

: Load Default Configuration

Display Setup Confirmation window. Press Enter to load default configuration.

: Select Sub-Menu

Some items have sub-menus. Display the sub-menu for a selected item.

: Save and Exit

Display Setup Confirmation window. Press Enterto save and exit.

: Exit

In a sub-menu, press Esc to move to the previous window. In Main menu, click Esc to move to Exit menu.



23/88

21

System Time

Current time. Use , , or keys to move around these fields. To change the

value, press < > or < > key.

System DateToday date. Use , , or keys to move around these fields. To change the value,

press < > or < > key. Set any date from year 1981 to 2079. It will automatically keep track of leap years.

The system date can also be set from the operating system.

Product Name

This shows the name of PC.

Processor Type

This shows the type of CPU.

Processor Spd

This shows the speed CPU.

BIOS VersionThis shows the Version of BIOS.

KBC Version

This shows the Version of KBD firm ware.

UUID

This is for display only. This shows the UUID.

Pri Master

Enter its submenu by pressing . In this submenu, it would show the device of Primary IDE Master

is HDD and its parameters.

Sec Slave

Enter its submenu by pressing . In this submenu, it would show the device of Secondary IDE

Slave is optical drive and its parameters.

Total Memory

This is for display only. This shows size of system memory.

Main menu



24/88

22

Legacy USB Support

There are two options to this field: Enabled, and Disabled. This field allows you to enable ordisable the

legacy USB support.

Boot-time Diagnostic ScreenEnables the Boot-time Diagnostic Screen.

SATA Controller Mode

Set SATA (Serial ATA) Controller Mode.

AHCI Configuration

Enables the AHCI (Advanced Host Controller Interface).

Battery Charge Stop Percentage

Set Battery Charge Stop Percentage.

Fan Mode Control

Set Fan Mode Control.

Fn Key SetupSet Sticky fn key function.

Wake On Lan

Enables Wake On Lan.

PXE/Remote Boot

Enables PXE/Remote Boot.

Execute-Disable Bit Capability

Enables Execute-Disable Bit Capability.

Advanced menu


Supervisor Password Is

This shows the systems supervisor password has been set, or not.

Set Supervisor Password

Set Supervisor Password.

User Password Is

This shows the systems User Password has been set, or not.

Set User Password

Set User Password.

Password on boot

Enables Password on boot.

HDD Password Is

This shows the systems HDD Password has been set, or not.

Set HDD Password

Set HDD Password.

Security menu


25/88

23


Exit Saving Changes

Select Exit Saving Changes to save new setup information in CMOS RAM. CMOS RAM stores the

information using the backup battery; therefore, the information will not be lost when the computer is

turned off.

Exit Discarding Changes

Select Exit Discarding Changes to discard new setup information. If you made changes to items other

than date, time, and passwords, the Setup Warning asks you to save the new configurations. Select Yes

and press Enter to save the new configuration.

Load Setup Defaults

Select Load Setup Defaults to change the setup information to the factory default settings. If you select

Load Setup Defaults or press F9, Setup Confirmation asks you to confirm your selection. Press Yes to

load setup defaults.

Discard Changes

Discard change value.

Save Changes

Save change value.

Exit menu

Boot menu enables you to set the boot order for the CD-ROM drive, Removable devices Hard drive,

and Network boot as shown below.

Boot menu


26/88

24

Note

If replacing a part (FRU) does not solve the problem, put the original part back in the computer.

Do not replace a non-defective FRU.

The symptom-to-part index in this section lists symptoms and errors and their possible causes.

The most likely cause is listed first.

Power system checkout

To verify a symptom, do the following :

1. Power off the computer.

2. Remove the battery pack.

3. Connect the AC adapter.

4. Check that power is supplied when you power on the computer.


6. Disconnect the AC adapter and install the charged battery pack.

7. Check that the battery pack supplies power when you power on the computer.

If you suspect a power problem, see the appropriate one of the following power supply checkouts :

1. Checking the AC adapter

2. Checking the operational charging

3. Checking the battery pack

4. Checking the backup battery

Chapter 4. Symptom-to-part index

Ch4. Symptom-to-part index


27/88

25

Checking the AC adapter

If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity

and installation.

If the computer does not charge during operation, go to Checking operational charging.

To check the AC adapter, do the following :

1. Unplug the AC adapter cable from the computer.

2. Measure the output voltage at the plug of the

AC adapter cable. See the following figure:

3. If the measured output voltage is incorrect, remove

the power cord from the AC adapter and then re-

connect it in about ten seconds.

4. Measure the output voltage at the plug of the AC adapter cable.

5. If the measured output voltage is incorrect, replace the AC adapter.

2

1Ground2

+18.0 ~ +19.21

Voltage (V dc)Pin



28/88

26

If the voltage is not correct, replace the AC adapter.

If the voltage is acceptable, do the following :

1. Replace the system board.

2. If the problem persists, check the AC adapter whether it is correct product or not.

Checking operational charging

1. To check whether the battery charges properly during operation, use a discharged battery pack or a

battery pack that has less than 50% of the total power remaining when installed in the computer.

Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery

does not turn on, replace the battery pack.

2. If the charge indicator still does not turn on, replace the system board.

Then reinstall the battery pack.

Note

Noise from the AC adapter does not always indicate a defect.

Note

Do not charge battery pack, when its temperature is below 0 or above 75 .

Checking the battery pack

1. Open the Power Meter window by clicking Start Control Panel Power Options and then;

check the total power remains. Battery charging does not start until the power Meter shows that less

than 95% of the total power remains; under this condition the battery pack can charge to 100% of its

capacity. This protects the battery pack from being overcharged or from having a shortened life.

2. To check the status of your batter, move your cursor to the Power Meter icon in the icon tray of the

Windows taskbar and wait for a moment (but do not click), and the percentage of battery power

remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.

Note

If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and

Leave it at room temperature for a while. After it cools down, reinstall and recharge it.



29/88

27

The Characteristics of the battery pack

1. Self-discharge

The battery gradually loses its power over time without ever being used.

2. Periodic full discharge / charge

Frequent recharge of the battery pack can reduce the capacity of the battery pack. When this happens,you can perform the full discharge / charge to improve the capacity. You should perform periodic full

discharge /charge once every 30~60 days.

You should always use the battery until its power is low; then fully charge the battery.

3. Trickle charge

If the temperature of the battery pack drops below 10 , the trickle charging begins.

The trickle charging may take 32 hours for the battery pack to be fully charged.



30/88

28

To check the battery pack, do the following :


2. Remove the battery pack and measure the voltage between battery terminals 1(-) and 5(+).

See the following figure :

+0V ~ +12.6V

(6 cell)5

Ground(-)1

Voltage (V dc)Terminal

Note

Charging will take at least 3 hours.

3. If the voltage is still less than +11.1 V DC after recharging, replace the battery.

4. If the voltage is more than +11.1 V DC, measure the resistance between battery terminals 1 and 2.

The resistance must be 2 to 4 (typically 3 ).

5. If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system

board.


Note

Battery is an expendable supplier, so its capacity and used time can be reduced by using the computer.

5(+) 4 3 2 1(-)


31/88

29

Numeric error codes

Replace the backup battery and run BIOS Setup Utility

to reset the time and date.

0250

System battery error System battery is dead

1. DIMM

2. System board

0232

Extended RAM error - Extended RAM Failed

at address line

System board0231

Shadow RAM error - Shadow RAM failed at

offset

1.DIMM

2.System board

0230

System RAM error - System RAM Failed at

offset.

Load Setup Defaults in BIOS Setup Utility.0220

Monitor type error - Monitor type does not

match the one specified in CMOS.

System board.0212

Keyboard Controller Failed

Run interactive tests of the keyboard and the auxiliary

input device.

0211

Keyboard error

1.Check the keyboard if it is pressed.

2.Replace the keyboard.

0210

Stuck Key error

1.Reset the hard-disk drive.

2.Load Setup Defaults in BIOS Setup Utility.3.Hard-disk drive.

4.System board.

0200

Fixed disk failure(The hard disk is not working)

FRU or action, in sequenceSymptom / Error



32/88

30


1. DIMM

2. System board

02F6

Software NMI failed

1. DIMM

2. System board

02F5

DMA test failed

1. Load Setup Default in BIOS Setup Utility.2. Replace the backup battery.

3. System board.

02F4EISA CMOS not writable

1. Load Setup Default in BIOS Setup Utility.

2. System board.

02D0

System cache error Cache disabled

(RAM cache failed and BIOS disabled)

Load Setup Defaults in BIOS Setup Utility.0281: Memory Size found by POST differed

from EISA CMOS

1. Load Setup Default in BIOS Setup Utility.

2. DIMM.

3. System board.

0280

Previous boot incomplete

- Default configuration used

Run BIOS Setup Utility to reset the time and date.0271

Check date and time settings Date and time

error.

1. Replace the backup battery and run BIOSSetup Utility to reset the time and date.

2. System board.

0260System timer error

Reset the password by running BIOS Setup Utility.0252

Password checksum bad The password is

cleared.

Replace the backup battery and run BIOS Setup Utilityto reset the time and date.

0251System CMOS checksum bad

System CMOS checksum is not correct.

Default configuration used.



33/88

31


1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

061A

Parallel port configuration error


2. System board.

0619

Parallel port configuration changed


2. System board.

0618

Floppy configuration error


2. System board.

0617

Floppy configuration changed


2. System board.

0616

Com B configuration error


2. System board.

0615

Com B configuration changed


2. System board.

0614

Com A configuration error


2. System board.

0613

Com A configuration changed


2. System board.

0612

IDE configuration error


2. System board.

0611

IDE configuration changed

1. DIMM

2. System board

02F7

Fail Safe timer NMI failed



34/88

32

System board.Thermal sensing error.

Fan.FAN error.

1. Restore the system configuration to what it was

before the computer entered hibernation mode.

2. If memory size has been changed, re-create the

hibernation file.

Hibernation error.

1. Check that the operating system has no failure and

is installed correctly.

2. Enter BIOS Setup Utility and see whether the hard

-disk drive and the diskette drive are properly

identified.

3. Reset the hard-disk drive.

4. Reinstall the operating system.

5. Diskette drive.

6. Hard-disk drive.

7. System board.

Operating System not found.


2. Backup battery.

3. System board.

I/O Device IRQ Conflict.

1. DIMM.

2. System board.

Invalid System Configuration Data.

1. DIMM.

2. System board.

Failing bits: nnnn.


2. Backup battery.

3. System board.

Allocation error for device.


2. Backup battery.3. System board.

Device address conflict.


Error message



35/88

33

LCD-related symptoms

Note

Before removing or disassembling LCD, power off the computer, unplug all power cords from electrical

outlets, remove the battery pack also.

LCD assembly.

System board.

Power-on indicator on, and a blank\LCD

during POST.

LCD assembly.Horizontal or vertical lines displayed

on LCD

1. Reset all LCD connectors.

2. Replace LCD cable.

3. LCD assembly.

4. System board.

LCD color cannot be adjusted.

LCD screen abnormal.

Characters missing pixels.

LCD screen unreadable.

Wrong color displayed.

1. Reconnect inverter to the board connector.

2. Replace inverter.

3. LCD assembly.

4. System board.

LCD backlight not working.

LCD too dark.

LCD brightness cannot be adjusted.

1. Check out Battery Miser.

2. Choose Never in the Turn off Monitor item on

Power Options Properties.

3. Check the power save mode switch if it is pressed

by something.4. Check the System is in standby or hibernation

mode.

Nothing displayed on LCD screen.

Check out Battery Miser.LCD screen becomes dark suddenly.




36/88

34

Indeterminate problems

You are here because the diagnostic tests did not identify which adapter or device failed, wrong devices

are installed, a short circuit is suspected, or the system is inoperative.

Follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects).

Verify that all attached devices are supported by the computer.

Verify that the power supply being used at the time of the failure is operating correctly.

1. Power off the computer

2. Visually check each FRU for damage. Replace any damaged FRU.

3. Remove or disconnected all of the following devices :

a. Non-LG devices.

b. Printer, mouse, and other external devices.

c. Battery pack.

d. PC cards.

e. ODD (CD-ROM, Combo) drive or FDD drive in the Bay.

f. Hard-disk drive.

Note

Use the other memory card because it needs when operating computer.

4. Power on the computer.

5. Determine whether the problem has changed.6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.

7. If the problem remains, replace the following FRUs one at a time.

(do not replace a non-defective FRU)

a. LCD assembly (Check external monitor whether the same problem recurs or not).

b. Keyboard.

c. Keydeck (TouchPad and Scroll Button assembly).

d. System board.



37/88

35

Chapter 5. Removing and replacing a part (FRU)

Note

As for the screw, every Torque 3 0.2Kgfcm(0.196Nm)

Danger

Before removing any FRU, power off the computer, unplug all power cords from electrical

outlets, remove the battery pack, and then disconnect any interconnecting cables.

Caution

Before the computer is powered on after FRU replacement, make sure that all screws, springs,

and other small parts are in place and are not loose inside the computer. Verify metal flakes can

cause electrical short circuits.

Ch5. Removing and replacing a part


38/88

36

1010 Battery Pack

1. Push the battery latch in the direction shown below; then slide the battery pack out of the slot.



39/88

37

1. Remove 2 HDD Cover Screws.

2. Open HDD Cover, then remove HDD.

Remove the following parts in order before replacing this part.

1. Battery Pack(1010)

1020 Hard Disk Drive



40/88

38

1. Push the ODD Knob in the direction shown below, then remove ODD from slot.


1. Battery Pack(1010)

1030 Optical Disk Drive



41/88

39

1. Remove 2 Screws.

2. Pull up the Hinge Cap using a (-) type screwdriver.


1. Battery Pack(1010) 2. Hard Disk Drive(1020)

1040 Retainer

2D4.0 X L4.01SZZBA4080A1

QtySpecificationFRU No.No.



42/88

40

3. Disconnect Retainer Connector.

4. Remove Retainer.



43/88

41

1. Remove 12 Screws.

12D4.5 X L6.51SZZBA4097B1


2. Disconnect Keyboard Connector.


1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. Retainer(1040)

1050 Keyboard



44/88

42

2. Remove Keyboard.



45/88

43

1. Remove 2 Hinge Screws. (Left / Right)

2D4.5 X L6.51SZZBA4097B1



1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. Retainer(1040) 4. Keyboard(1050)

1060 Display Module

2. Remove Display Module.



46/88

44

1. Disconnect RTC Battery Connector then, remove RTC Battery.

2. Remove 7 Screws.

7D4.0 X L4.01SZZBA4080A1




5. Display Module(1060)

1070 Key Deck



47/88

45

3. Remove Key Deck.

2. Disconnect Touchpad Connector.



48/88

46

1. Remove 5 Sub B/D Screws.

2. Remove Sub B/D.

5D4.0 X L4.01SZZBA4080A1




5. Display Module(1060) 6. Key Deck(1070)

1080 Sub B/D



49/88

47

1. Remove 4 Speaker Screws.

2. Remove Speakers.

4D8.0 X L6.51SZZBA4027A1




5. Display Module(1060) 6. Key Deck(1070) 7. Sub B/D(1080)

1090 Speaker



50/88

48

1. Remove 5 Screws.

2. Remove Fan Assy.

4D4.0 X L8.81SZZBA4020A1

1D2.0 X L5.01SZZBZ4014C2


1

2

1

1

1



5. Display Module(1060) 6. Key Deck(1070) 7. Sub B/D(1080) 8. Speaker(1090)

1100 Fan Assembly



51/88

49

1. Remove ODD Plate.

2. Remove 3 Screws, then remove I/O Jack Sub Board.

3D4.0 X L4.01SZZBA4080A1




5. Display Module(1060) 6. Key Deck(1070) 7. Sub B/D(1080) 8. Speaker(1090)

9. Fan Assy(1100)

1110 Main Board



52/88

50

3. Remove a Screw, then remove Hinge Left.

1D4.0 x L4.01SZZBA4080A1


1D4.0 x L4.01SZZBA4080A1


4. Remove a Screw, then remove Hinge Right.



53/88

51

6. Remove Main Board.

5. Remove 2 Screws and 1 Hexagon Screw.

2D4.0 X L4.01SZZBA4080A1

1D2.0 x L11.51SZZBA4101A2


1

2

1



54/88

52



55/88

53

1. Remove 6 Rubber Caps, then remove 4 Screws.

2. Remove LCD Front.

4D2.5 X L4.51SZZBA4104A1




5. Display Module(1060)

1120 Display Module Exploded View



56/88

54

4D2.5 X L4.51SZZBA4104A1


3. Remove 4 Screws.

4. Remove LCD Hinge. (Left / Right).



57/88

55

5. Remove Inverter.



58/88

56

6. Disconnect LED Sub Board Connector.



59/88

57

7. Remove 2 Screws, then remove LED Sub Board.

2D3.5 X L3.01SZZBA4041A1


8. Remove LED Lens.



60/88

58

9. Remove 2 Screws, then remove Left Antenna.

10. Remove 2 Screws, then remove Right Antenna.

2D3.5 X L3.01SZZBA4041A1


2D3.5 X L3.01SZZBA4041A1




61/88

59



62/88

60

12. Remove 4 Screws, then remove LCD Brackets.

4D3.5 X L3.01SZZBA4041A1


13. Disconnect LCD Cable.



63/88

61

2005-06-20 WNR05Chapter 6. Part lists

Ch6. Part lists

PLATE WINDRIVER ODD BAY3300BP3520ANPLT1

WINDRIVER DISPLAY FRONT ASSY3111B97122ANCSE3

WINDRIVER KBD DECK ASS Y3111B0TS79ANCSE4

WINDRIVER ZN HINGE FRAME L3110BM3037ANFRM1

WINDRIVER ZN HINGE FRAME R3110BM3036ANFRM2

WINDRIVER MG BOTTOM CASE3110BD0020ANCSE5

UJDA765 PANASONIC 8X 24X 24X 24X 9.5MM ROHS WINDRIVER COMBO

ASSY2029B09005ANODD2

GCC-4246N HLDS 8X 24X 24X 24X 9.5MM ROHS WINDRIVER COMBO ASSY2029B09004ANODD2

UJ-822BPT1-G PCC 8X 8X 24X 24X 10X 2X 2X 2.4X 2.4X 2X 24X NOTE BOOK

9.5MM ROHS WINDRIVER SUPER MULTI

2026B10007ANODD2

+ D8.0 L6.5MM MSWR3 / FN SPEAKER SILVER WINDRIVER SPEAKER SCREW1SZZBZ4027ANSCRA

+ D4.0 L8.8MM SWRH4 FAN ASSEMBLY SILVER MCKINLEY L(10.0) WITH

HEAD LENGTH TIP#01SZZBZ4020AHTM18

HEXAGON D2.0 L11.5MM BSP, BSW HEXA SAMWON YL WINDRIVER M2

H6.0MM INNER1SZZBA4101ANSCR9

+ D4.5 L6.5MM SWRH4 M2.5 H1.0 BK HUNTER TIP NO.0 ROHS 1601SZZBA4097BNSCR7

+ D2.5 L4.5MM MSWR3 / FN . BK WINDRIVER .1SZZBA4104ANSCRB

+ D4.0 L4.0MM SWRH4 M2 H1.0 SILVER K2 TIP#01SZZBA4080ALUS08

HYMP532S64P6-C4 HYNIX 200P SODIMM BK 256MB 32MX64 533MHZ DDR2

SDRAM WITH 32MX160IMMR00053BNMEM1

HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ

DDR2 SDRAM WITH 32MX160IMMR00008ANMEM1

M470T3354BZ0-CD5 SAMSUNG ELECTRONICS 200P SODIMM BK 256MB

32MX64 533MHZ DDR2 SDRAM WITH 32MX16 PB FR0IMMR00005BNMEM1

RH80536GE0302M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 740

1.73GHZ/800MHZ C0-STEPPING(SL7SA)0IMCR00009ANCPU1


1.86GHZ/800MHZ C0-STEPPING(SL7S9)0IMCR00007ANCPU1


2.00GHZ/800MHZ C0-STEPPING(SL7SM)0IMCR00005ANCPU1


2.13GHZ/800MHZ C0-STEPPING(SL7SL)0IMCR00003ANCPU1

RemarksSpecificationPart NumberLocation


64/88

62

Ch6. Part lists

WINDRIVER PCABS BATTERY KNOB4940BM4174ANNOB1

WINDRIVER PCABS DRIVE KNOB LOCK HOLDER4930BM4047ANHLD3

WINDRIVER PCABS BATTERY KNOB HOLDER RIGHT4930BM4046ANHLD2

WINDRIVER PCABS BATTERY KNOB HOLDER LEFT4930BM4045ANHLD1

WINDRIVER RUBBER HDD HOLDER4930BM3101ANHLD4

WINDRIVER EVA DISPLAY REAR LCD CONN4850BP4078ANCSN9

WINDRIVER EVA DISPLAY REAR RIGHT4850BP4073ANCSN7

WINDRIVER EVA DISPLAY REAR LEFT4850BP4072ANCSN6

WINDRIVER EVA DISPLAY REAR CENTER4850BP4071ANCSN5

WINDRIVER RUBBER DISPLAY FRONT LOWER 12.1INCH4850BP4068ANCSN4

WINDRIVER RUBBER DISPLAY FRONT UPPER 12.1INCH4850BP4067ANCSN3

WINDRIVER SUS LCD RIGHT 0.5T 12.1INCH4810BP3354ANBRK2

WINDRIVER SUS LCD LEFT 0.5T 12.1INCH4810BP3353ANBRK1

WINDRIVER 6.5 KGF-CM HINGE LEFT LATCHLESS 12.1INCH4775B00058ANHNG1

WINDRIVER 6.5 KGF-CM HINGE RIGHT LATCHLESS 12.1INCH4775B00057ANHNG2

. WINDRIVER SHEET INSULATION BOTTOM RIGHT3858BZ4498ANSHT6

. WINDRIVER SHEET INSULATION BOTTOM3858BZ3038ANSHT5

. WINDRIVER SPEAKER GRILL RIGHT3858BP4483ANSHT4

. WINDRIVER SPEAKER GRILL LEFT3858BP4482ANSHT3

N WINDRIVER BADGE LG LOGO3858BP4480ANSHT2

ID LABEL WINDRIVER .3850BB9214ANLBL2

US ENGLISH WINDRIVER SUNREX 84KEY3823B01151ANKBD2

KOREA WINDRIVER SUNREX 84KEY3823B01150ANKBD2

WINDRIVER PMMA LED DISPLAY 12.1INCH3680BM4092ANLED1

WINDRIVER RUBBER BOTTOM3610BP4025ANCSN1

WINDRIVER RUBBER SPEAKER CUSHION3610BM4033ANCSN2

WINDRIVER HDD COVER3551B90008ANCVR7

WINDRIVER . MINI PCI ASSY3551B90006BNCVR6

WINDRIVER . 4 IN 1 ASSY3551B90005ANCVR5

WINDRIVER MEMORY DOOR ASSY3551B90004BNCVR4

WINDRIVER . RETAINER ASSY ()3551B90003ANCVR3

WINDRIVER PCABS . ODD WEIGHT SAVER COVER3550BM4200ANCVR2

PLATE WINDRIVER HDD3300BP4472ANPLT2



65/88

63

Ch6. Part lists

LCD CABLE 100X147 25 WINDRIVER, WANSHIH6851B34039ANCAB4

AWM 20696 80C VW-1 32 . 36X16.5, 0.5PITCH KFC WINDRIVER, AUDIO BD TOMAIN BD

6850B32001ANCAB3

MK6006GAH TOSHIBA 60GB EIDE INNER 4200RPM WIND RIVER6744A00003ANHDD2

MK4006GAH TOSHIBA 40GB EIDE INNER 4200RPM WIND RIVER6744A00002ANHDD2

MK3006GAL TOSHIBA 30GB EIDE INNER 4200RPM WIND RIVER6744A00001ANHDD2

WM3B2915AGRWF INTEL IEEE 802.11ABG STANDARD PROTOCOL 54M 4

LAYERS REV 3.0 MINIPCI TYPE IIIB FORM FAC6718M000018NLAN1

WM3B2915AGNAF INTEL IEEE 802.11ABG STANDARD PROTOCOL 54M 4

LAYERS REV 3.0 MINIPCI TYPE IIIB FORM FAC6718M000015NLAN1

WM3B2200BGRWF INTEL INTERFACE STANDARD IEEE802.11G 54M 4

LAYERS REV 3.0 PRO/WIRELESS 2200BG LAN MINI6718M000014NLAN1

WM3B2200BGMWF INTEL INTERFACE STANDARD IEEE802.11G 54M 4

LAYERS REV 3.0 PRO/WIRELESS 2200BG LAN MINI6718M000013NLAN1

IM8822 NMB GENERAL GENERAL GENERAL WINDRIVER OZ9646708BI0097ANINV1

KUBNKM106A ALPS GENERAL GENERAL GENERAL WINDRIVER OZ99106708BI0096ANINV1

HP-OK065B13 HIPRO 65W 18.5V/3.5A 3PIN WITHOUT PFC WINDRIVER6708BA0044PNACA1

PA-1650-02GR LITEON 65W 18.5V/3.5A 3PIN WITHOUT PFC WINDRIVER6708BA0036PNACA1

SP-022+IS-034 H05VV-F I-SHENG KS 1000MM 3P CONN W/VELCRO TIE

BLACK6410BM21601NCABC

PT8XXK9KB0A-033 LONGWELL KS 1000MM 3P CONN W/VELCRO TIE BLACK6410BM21002NCABC

. ESTEC 1.5W . . SPEAKER L WINDRIVER6401B02547ANSPK1

. ESTEC 1.5W . . SPECKER R WINDRIVER6401B02546ANSPK2

N121I1-L02 CHIMEI TFT COLOR 12.1 INCH WXGA 1280X800 LVDS 200NITS

GLARE6304FCI010ANLCD2

THERMAL FAN ASSY WINDRIVER TOSHIBA5901B09287ANFAN2

THERMAL SILICON 12X12MM, 0.5T HUNTER COH2003, DARK ORANGE,

CONDUCTIVIEY 3.5W/MK, NORTHBRDIGE5022BZ4027ANPADN

THERMAL PCS-TC-11-T-13 19X19MM T130UM ZEBRA-2(MOBILE) GRAY

K=4.7(W/M-C)5022BZ4025AMKM16

HITACHI WIRELESS L WINDRIVER5011B00027ANANT1

HITACHI WIRELESS R WINDRIVER5011B00026ANANT2

WD0.25MM ID3.0MM N9 L11.0MM 0.6KGF WINDRIVER BATEERY SPRING4970BW4570ANSPR1

WINDRIVER PCABS DRIVE KNOB LOCK4940BM4175ANNOB2



66/88

64

Ch6. Part lists

INTEL GRYPHON BANIAS LOGO 252352-001 INTEL CENTRINO LABEL N N3850BB9110CHTM14

PL8B1S3J10A-060 LONGWELL SAA 1830MM 3PIN CONN BLAC6410BK21005NCABC

SUB / N WIMTEC 4 LAYERS REV0.5 WINDRIVER MP I/O JACK SUB B/D ASSY

PB FREE6871BWRG3PCNSUB1

WINDRIVER KENGSINGTON LOCK3858BZ4510ANSHT9

SUB / N WIMTEC 4 LAYERS REV0.5 WINDRIVER MP I/O JACK SUB B/D ASSY

PB FREE6871BWRG3PBNSUB1

DISPLAY HUNTER-ALL PB FREE3858BZ4513ANSHT8

NT Windriver DMB moduleLGPCDMB04NDMB1

WIN XP, DT ALL, NEW3850BB4125ANLBL5

POP LABEL WINDRIVER EXPORT3850BF9048ANLBL4

POP LABEL WINDRIVER DOMESTIC3850BF9047ANLBL3

EMI FABRIC 10X30X0.7 WINDRIVER FOR WIRELESS LAN4986BZ4202ANGSK1

WINDRIVER LED PROTECT LIGHT3858BZ4511ANSHT7

WINDRIVER . RETAINER ASSY () X-note3551B90003BNCVR9

LCD CABLE 100X147 25 WINDRIVER, WANSHIH6851B34038ANCAB4

+ D3.5 L3.0MM SWRH4 DUMMY COVER FIX SILVER MAGELLAN DISPLAY1SZZBA4041AHTO03

Screw, M2.0xL5.0bk1SZZBZ4014CNSCRD

Screw, M2.0xL3.5bk1SZZBA4017FNSCRC

WINDRIVER RUBBER MIC .3610BM4034ANCSN8

160MHA CR2025 SONY LI-ION COIN WINDRIVER RTC ASSY6911B00125ANRTC1

4800MAH 3S-2P SIMPLO LI-ION CYLINDERICAL WINDRIVER SANYO CELL6911B00122BNBAT1

4800MAH 3S-2P SIMPLO LI-ION CYLINDERICAL WINDRIVER LGC CELL6911B00122ANBAT1

WIMTEC 1 LAYERS WINDRIVER TOSHIBA HDD FPC ASSY6871BWRG7PANCAB2

N WIMTEC 2 LAYERS REV0.3 WINDRIVER PILOT LCD LED B/D ASSY PB

FREE6871BWRG4PANSUB3

N LGE 4 LAYERS REV0.5 WINDRIVER PILOT AUDIO BD ASSY PB FREE6871BWRG0AANSUB2

N LGE 10 LAYERS REV 0.5 WINDRIVER MP 10/100 MAIN B/D ASSY6871BWRTBAANMLB2

N LGE 10 LAYERS REV 0.5 WINDRIVER MP GIGA MAIN B/D ASSY6871BWRGBAANMLB2

MA560-3 LF(LEAD FREE) QCOM 2 LAYERS 1A MDC1.5 FORM FACTOR V.92

MODEM CARD6871BG869AANMDM2

T60M893.05 FOXCONN 2 LAYERS 00L0 AZALIA MDC1.5 FORMFACTORINTERNAL 56K MDC MODEM LF(LEAD FREE)

6871BG867ABNMDM2

MODEM CABLE 70 2 WINDRIVER, MDC CABLE6851B34040ANCAB5



67/88

65

Ch6. Part lists

NORWAY WINDRIVER SUNREX3823B01167ANKBD2

FRENCH SILVER WINDRIVER SUNREX3823B01166BNKBD2

FRENCH WINDRIVER SUNREX3823B01166ANKBD2

DENMARK SILVER WINDRIVER SUNREX3823B01165BNKBD2

DENMARK WINDRIVER SUNREX3823B01165ANKBD2

SWEDEN FINLAND SILVER WINDRIVER SUNREX3823B01164BNKBD2

SWEDEN FINLAND WINDRIVER SUNREX3823B01164ANKBD2

ITALY SILVER WINDRIVER SUNREX3823B01163BNKBD2

ITALY WINDRIVER SUNREX3823B01163ANKBD2

BRAZIL SILVER WINDRIVER SUNREX3823B01162BNKBD2

BRAZIL WINDRIVER SUNREX3823B01162ANKBD2

HUNGARY SILVER WINDRIVER SUNREX3823B01161BNKBD2

HUNGARY WINDRIVER SUNREX3823B01161ANKBD2

CANADIAN FRENCH SILVER WINDRIVER SUNREX3823B01160BNKBD2

CANADIAN FRENCH WINDRIVER SUNREX3823B01160ANKBD2

GERMAN SILVER WINDRIVER SUNREX3823B01159BNKBD2

GERMAN WINDRIVER SUNREX3823B01159ANKBD2

TURKISH SILVER WINDRIVER SUNREX3823B01158BNKBD2

TURKISH WINDRIVER SUNREX3823B01158ANKBD2

HEBREW SILVER WINDRIVER SUNREX3823B01157BNKBD2

HEBREW WINDRIVER SUNREX3823B01157ANKBD2

PORTUGUESE SILVER WINDRIVER SUNREX3823B01156BNKBD2

PORTUGUESE WINDRIVER SUNREX3823B01156ANKBD2

SPANISH SILVER WINDRIVER SUNREX3823B01155BNKBD2

SPANISH WINDRIVER SUNREX3823B01155ANKBD2

ARABIC SILVER WINDRIVER SUNREX3823B01154BNKBD2

ARABIC WINDRIVER SUNREX3823B01154ANKBD2

RUSSIA SILVER WINDRIVER SUNREX3823B01153BNKBD2

RUSSIA WINDRIVER SUNREX3823B01153ANKBD2

US INTER SILVER WINDRIVER SUNREX3823B01152BNKBD2

US INTER WINDRIVER SUNREX3823B01152ANKBD2

US ENGLISH WINDRIVER SUNREX 84KEY SILVER3823B01151BNKBD2

KOREA WINDRIVER SUNREX 84KEY SILVER3823B01150BNKBD2



68/88

66

Ch6. Part lists

WINDRIVER PC COVER ANTENNA 12.1INCH3550BM2102ANCVRA

WINDRIVER . CASE REAR BLUE X-NOTE LOGO3111B97126BNCSE2

WINDRIVER . CASE REAR SILVER X-NOTE LOGO3111B97126ANCSE2

WINDRIVER . CASE REAR BLUE LG LOGO3111B97125BNCSE2

WINDRIVER . CASE REAR SILVER LG LOGO3111B97125ANCSE2

M470T6554BZ0-CD5 SAMSUNG ELECTRONICS 200P SODIMM BK 512MB

64MX64 533MHZ DDR2 SDRAM WITH 32MX16 PB FR0IMMR00006BNMEM1

TAIWAN SILVER WINDRIVER SUNREX3823B01168BNKBD2

TAIWAN WINDRIVER SUNREX3823B01168ANKBD2

NORWAY SILVER WINDRIVER SUNREX3823B01167BNKBD2



69/88

1

LW20

Location LG P/N SPECIFICATION REMARKS

UJ-822BPT1-G PCC 8X 8X 24X 24X 10X 2X 2X 2.4XDVD

NODD2 2026B10007A 2.4X 2X 24X NOTE BOOK 9.5MM ROHS WINDRIVERREWRITABLE

SUPER MULTI

NODD2 2029B09004AGCC-4246N HLDS 8X 24X 24X 24X 9.5MM ROHS COMBO

WINDRIVER COMBO ASSY ASSEMBLY

NODD2 2029B09005AUJDA765 PANASONIC 8X 24X 24X 24X 9.5MM COMBO

ROHS WINDRIVER COMBO ASSY ASSEMBLY

NBAT1 6911B00122A4800MAH 3S-2P SIMPLO LI-ION CYLINDERICAL BATTERY

WINDRIVER LGC CELL ASSEMBLY

NBAT1 6911B00122B4800MAH 3S-2P SIMPLO LI-ION CYLINDERICAL BATTERY

WINDRIVER SANYO CELL ASSEMBLY


70/88

2

LW20


71/88

3

LW20


NSCRC 1SZZBA4017FScrew, M2.0xL3.5bk SCREW,DRAWING

T60M893.05 FOXCONN 2 LAYERS 00L0 AZALIA PWB(PCB)

NMDM2 6871BG867ABMDC1.5 FORMFACTOR INTERNAL 56K MDC ASSEMBLY

MODEM LF(LEAD FREE) MAIN

NMDM2 6871BG869AAMA560-3 LF(LEAD FREE) QCOM 2 LAYERS 1A PWB(PCB)

MDC1.5 FORM FACTOR V.92 MODEM CARD ASSEMBLY,MAIN

NCVR4 3551B90004B WINDRIVER MEMORY DOOR ASSY COVER

NCVR6 3551B90006B WINDRIVER . MINI PCI ASSY COVER

NCVR7 3551B90008A WINDRIVER HDD COVER COVER

M470T3354BZ0-CD5 SAMSUNG ELECTRONICS 200P

NMEM1 0IMMR00005B SODIMM BK 256MB 32MX64 533MHZ DDR2 SDRAM IC,MEMORIES

WITH 32MX16 PB FR

HYS64T64020HDL-3.7-A INFINEON 200P SODIMM

NMEM1 0IMMR00008A BK 512MB 64MX64 533MHZ DDR2 SDRAM WITH IC,MEMORIES

32MX16

NMEM1 0IMMR00053BHYMP532S64P6-C4 HYNIX 200P SODIMM BK

IC,MEMORIES256MB 32MX64 533MHZ DDR2 SDRAM WITH 32MX16

M470T6554BZ0-CD5 SAMSUNG ELECTRONICS 200P

NMEM1 0IMMR00006B SODIMM BK 512MB 64MX64 533MHZ DDR2 SDRAM IC,MEMORIES

WITH 32MX16 PB FR

NCAB5 6851B34040A MODEM CABLE 70 2 WINDRIVER, MDC CABLE CABLE ASSEMBLY


72/88

4

LW20


NSCR7 1SZZBA4097B+ D4.5 L6.5MM SWRH4 M2.5 H1.0 BK HUNTER

SCREW,DRAWINGTIP NO.0 ROHS 160

NCSN1 3610BP4025A WINDRIVER RUBBER BOTTOM FOOT

NNOB1 4940BM4174A WINDRIVER PCABS BATTERY KNOB KNOB

NNOB2 4940BM4175A WINDRIVER PCABS DRIVE KNOB LOCK KNOB

WM3B2200BGMWF INTEL INTERFACE STANDARD LANCARDNLAN1 6718M000013 IEEE802.11G 54M 4 LAYERS REV 3.0 PRO/WIRELESS

MINI PCI2200BG LAN MINI

WM3B2200BGRWF INTEL INTERFACE STANDARDLANCARD

NLAN1 6718M000014 IEEE802.11G 54M 4 LAYERS REV 3.0 PRO/WIRELESSMINI PCI

2200BG LAN MINI

WM3B2915AGNAF INTEL IEEE 802.11ABGLANCARD

NLAN1 6718M000015 STANDARD PROTOCOL 54M 4 LAYERS REV 3.0MINI PCI

MINIPCI TYPE IIIB FORM FAC

WM3B2915AGRWF INTEL IEEE 802.11ABGLANCARD

NLAN1 6718M000018 STANDARD PROTOCOL 54M 4 LAYERS REV 3.0MINI PCI

MINIPCI TYPE IIIB FORM FAC

NSCRC 1SZZBA4017F Screw, M2.0xL3.5bk SCREW,DRAWING


73/88


5

LW20

NCAB2 6871BWRG7PAWIMTEC 1 LAYERS - WINDRIVER TOSHIBA HDD PWB(PCB)

FPC ASSY ASSEMBLY,FPC

NPLT2 3300BP4472A PLATE WINDRIVER HDD PLATE

NHDD2 6744A00001AMK3006GAL TOSHIBA 30GB EIDE INNER 4200RPM

HDD,1.8"WIND RIVER

NHDD2 6744A00002AMK4006GAH TOSHIBA 40GB EIDE INNER 4200RPM

HDD,1.8"WIND RIVER

NHDD2 6744A00003AMK6006GAH TOSHIBA 60GB EIDE INNER 4200RPM

HDD,1.8WIND RIVER"

NHLD4 4930BM3101A WINDRIVER RUBBER HDD HOLDER HOLDER

NCVR3 3551B90003A WINDRIVER . RETAINER ASSY COVER


74/88

6

LW20


NKBD2 3823B01150A KOREA WINDRIVER SUNREX 84KEY KBD ASSEMBLY

NKBD2 3823B01151A US ENGLISH WINDRIVER SUNREX 84KEY KBD ASSEMBLY


75/88

7

LW20


NKBD2 3823B01150B KOREA WINDRIVER SUNREX 84KEY SILVER KBD ASSEMBLY

NKBD2 3823B01151B US ENGLISH WINDRIVER SUNREX 84KEY SILVER KBD ASSEMBLY

NKBD2 3823B01152A US INTER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01152B US INTER SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01153A RUSSIA WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01153B RUSSIA SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01154A ARABIC WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01154B ARABIC SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01155A SPANISH WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01155B SPANISH SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01156A PORTUGUESE WINDRIVER SUNREX KBD ASSEMBLYNKBD2 3823B01156B PORTUGUESE SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01157A HEBREW WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01157B HEBREW SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01158A TURKISH WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01158B TURKISH SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01159A GERMAN WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01159B GERMAN SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01160A CANADIAN FRENCH WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01160B CANADIAN FRENCH SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01161A HUNGARY WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01161B HUNGARY SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01162A BRAZIL WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01162B BRAZIL SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01163A ITALY WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01163B ITALY SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01164A SWEDEN FINLAND WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01164B SWEDEN FINLAND SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01165A DENMARK WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01165B DENMARK SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01166A FRENCH WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01166B FRENCH SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01167A NORWAY WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01167B NORWAY SILVER WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01168A TAIWAN WINDRIVER SUNREX KBD ASSEMBLY

NKBD2 3823B01168B TAIWAN SILVER WINDRIVER SUNREX KBD ASSEMBLY


76/88


8

NSCR7 1SZZBA4097B+ D4.5 L6.5MM SWRH4 M2.5 H1.0 BK HUNTER

SCREW,DRAWINGTIP NO.0 ROHS 160

LW20


77/88


9

LUS08 1SZZBA4080A + D4.0 L4.0MM SWRH4 M2 H1.0 SILVER K2 TIP#0 SCREW,DRAWING

NRTC1 6911B00125A160MHA CR2025 SONY LI-ION COIN WINDRIVER BATTERY

RTC ASSY ASSEMBLY

NCSE4 3111B0TS79A WINDRIVER KBD DECK ASS Y CASE ASSEMBLY

LW20


78/88

10

LW20


NSUB2 6871BWRG0AAN LGE 4 LAYERS REV0.5 WINDRIVER PILOT PWB(PCB)

AUDIO BD ASSY PB FREE ASSEMBLY,SUB


NCAB3 6850B32001AAWM 20696 80C VW-1 32 . 36X16.5, 0.5PITCH KFC CABLE

WINDRIVER, AUDIO BD TO MAIN BD CONNECTING

NCSN8 3610BM4034A WINDRIVER RUBBER MIC . FOOT


79/88

11

LW20


NFAN2 5901B09287A THERMAL FAN ASSY WINDRIVER TOSHIBA FAN ASSEMBLY

MKM16 5022BZ4025ATHERMAL PCS-TC-11-T-13 19X19MM T130UM

PADZEBRA-2(MOBILE) GRAY K=4.7(W/M-C)

NSPK1 6401B02547A . ESTEC 1.5W . . SPEAKER L WINDRIVER SPEAKER

NSPK2 6401B02546A . ESTEC 1.5W . . SPECKER R WINDRIVER SPEAKER

NSCRA 1SZZBZ4027A+ D8.0 L6.5MM MSWR3 / FN SPEAKER SILVER SCREW

WINDRIVER SPEAKER SCREW DRAWING

NSCRD 1SZZBZ4014C Screw, M2.0xL5.0bk SCREW,DRAWING

NCSN2 3610BM4033A WINDRIVER RUBBER SPEAKER CUSHION FOOT

HTM18 1SZZBZ4020A+ D4.0 L8.8MM SWRH4 FAN ASSEMBLY SILVER SCREW

MCKINLEY L(10.0) WITH HEAD LENGTH TIP#0 DRAWING


80/88


12


NSUB1 6871BWRG3PBSUB / N WIMTEC 4 LAYERS REV0.5 WINDRIVER PWB(PCB)

MP I/O JACK SUB B/D ASSY PB FREE ASSEMBLY

NPLT1 3300BP3520A PLATE WINDRIVER ODD BAY PLATE

NFRM1 3110BM3037A WINDRIVER ZN HINGE FRAME L CASE

NFRM2 3110BM3036A WINDRIVER ZN HINGE FRAME R CASE

LW20


81/88

13

LW20


82/88


14


RH80536GE0462M LG INTEL 478P UFCPGAIC,MICRO

NCPU1 0IMCR00003A TRAY NT CPU PENTIUM-M 770 2.13GHZ/800MHZCONTROLLER

C0-STEPPING(SL7SL)



C0-STEPPING(SL7SM)



C0-STEPPING(SL7S9)



C0-STEPPING(SL7SA)

NSCR9 1SZZBA4101AHEXAGON D2.0 L11.5MM BSP, BSW HEXA

SCREW,DRAWINGSAMWON YL WINDRIVER M2 H6.0MM INNER

MKM16 5022BZ4025ATHERMAL PCS-TC-11-T-13 19X19MM T130UM

PADZEBRA-2(MOBILE) GRAY K=4.7(W/M-C)

THERMAL SILICON 12X12MM, 0.5T HUNTER

NPADN 5022BZ4027A COH2003, DARK ORANGE, CONDUCTIVIEY 3.5W/MK, PAD

NORTHBRDIGE

NCVR5 3551B90005A WINDRIVER . 4 IN 1 ASSY COVER

NMLB2 6871BWRGBAA N LGE 10 LAYERS REV 0.5 WINDRIVER MP GIGA PWB(PCB)MAIN B/D ASSY ASSEMBLY,MAIN

NMLB2 6871BWRTBAAN LGE 10 LAYERS REV 0.5 WINDRIVER MP 10/100 PWB(PCB)

MAIN B/D ASSY ASSEMBLY,MAIN

LW20


83/88


15

NSHT3 3858BP4482A . WINDRIVER SPEAKER GRILL LEFT SHEET (MECH)NSHT5 3858BZ3038A . WINDRIVER SHEET INSULATION BOTTOM SHEET (MECH)

NSHT6 3858BZ4498A . WINDRIVER SHEET INSULATION BOTTOM RIGHT SHEET (MECH)

NCSE5 3110BD0020A WINDRIVER MG BOTTOM CASE CASE

NHLD1 4930BM4045A WINDRIVER PCABS BATTERY KNOB HOLDER LEFT HOLDER

NHLD2 4930BM4046A WINDRIVER PCABS BATTERY KNOB HOLDER RIGHT HOLDER

NHLD3 4930BM4047A WINDRIVER PCABS DRIVE KNOB LOCK HOLDER HOLDER

NHLD4 4930BM3101A WINDRIVER RUBBER HDD HOLDER HOLDER

NSPR1 4970BW4570AWD0.25MM ID3.0MM N9 L11.0MM 0.6KGF

SPRING,COILWINDRIVER BATEERY SPRING

LW20


84/88


16

NSCRB 1SZZBA4104A + D2.5 L4.5MM MSWR3 / FN . BK WINDRIVER . SCREW,DRAWING

NCSN3 4850BP4067AWINDRIVER RUBBER DISPLAY FRONT UPPER

CUSHION12.1INCH

NCSN4 4850BP4068AWINDRIVER RUBBER DISPLAY FRONT LOWER

CUSHION12.1INCH

NCSE3 3111B97122A WINDRIVER DISPLAY FRONT ASSY CASE ASSEMBLY

LW20


85/88


17

NSCRB 1SZZBA4104A + D2.5 L4.5MM MSWR3 / FN . BK WINDRIVER . SCREW,DRAWING

NHNG1 4775B00058AWINDRIVER 6.5 KGF-CM HINGE LEFT LATCHLESS HINGE

12.1INCH ASSEMBLY

NHNG2 4775B00057AWINDRIVER 6.5 KGF-CM HINGE RIGHT LATCHLESS HINGE

12.1INCH ASSEMBLY

NINV1 6708BI0096AKUBNKM106A ALPS GENERAL GENERAL GENERAL POWER SUPPLY

WINDRIVER OZ9910 INVERTER

NINV1 6708BI0097A IM8822 NMB GENERAL GENERAL GENERAL POWER SUPPLYWINDRIVER OZ964 INVERTER

LW20


86/88

18

LW20


87/88

19

LW20


HTO03 1SZZBA4041A+ D3.5 L3.0MM SWRH4 DUMMY COVER FIX SILVER

SCREW,DRAWINGMAGELLAN DISPLAY

NANT1 5011B00027A HITACHI WIRELESS L WINDRIVER ANTENNA

NANT2 5011B00026A HITACHI WIRELESS R WINDRIVER ANTENNA

NLED1 3680BM4092A WINDRIVER PMMA LED DISPLAY 12.1INCH LENS

NINV1 6708BI0096AKUBNKM106A ALPS GENERAL GENERAL GENERAL POWER SUPPLY


NINV1 6708BI0097AIM8822 NMB GENERAL GENERAL GENERAL POWER SUPPLY


NCSN5 4850BP4071A WINDRIVER EVA DISPLAY REAR CENTER CUSHION

NCSN6 4850BP4072A WINDRIVER EVA DISPLAY REAR LEFT CUSHION

NCSN7 4850BP4073A WINDRIVER EVA DISPLAY REAR RIGHT CUSHION

NCSN9 4850BP4078A WINDRIVER EVA DISPLAY REAR LCD CONN CUSHION

NSHT2 3858BP4480A N WINDRIVER BADGE LG LOGO SHEET (MECH)

NSHT7 3858BZ4511A WINDRIVER LED PROTECT LIGHT SHEET (MECH)

NCSE2 3111B97125A WINDRIVER . CASE REAR SILVER LG LOGO CASE ASSEMBLY

NCSE2 3111B97125B WINDRIVER . CASE REAR BLUE LG LOGO CASE ASSEMBLY

NCSE2 3111B97126A WINDRIVER . CASE REAR SILVER X-NOTE LOGO CASE ASSEMBLY

NCSE2 3111B97126B WINDRIVER . CASE REAR BLUE X-NOTE LOGO CASE ASSEMBLY

NCVRA 3550BM2102A WINDRIVER PC COVER ANTENNA 12.1INCH COVER


88/88

LW20

5 Service Manual - LG -Lw20

Documents

Transcript of 5 Service Manual - LG -Lw20