Documentos 10540 Mantenimiento Instalaciones Termicas GT1 07 d97da097
PVdF BICAPA - Fixfas · 2020. 5. 13. · Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS...
Transcript of PVdF BICAPA - Fixfas · 2020. 5. 13. · Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS...
Polígono Industrial de Bayas. C/ Ircio. Parcelas R72-77 - 09200 Miranda de Ebro, Burgos. SPAIN Tel.: +34 947 333 320 - Fax: +34 947 324 913 - [email protected] - www.alucoil.com
CABEBA
PVdF BICAPA Espesor de pintura EN 13523-1
25µ (-4µ / +4µ) 70% Kynar 500
Brillo especular EN 13523-2
Brillo medido a 60º Gardner: 30 g.u. (tolerancias según la NORMA EN 1396, tabla 4)
Dureza, método del lápiz EN 13523-4
≥HB
Adherencia EN 13523-5
Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS
Adherencia & Impacto EN 13523-6
Pérdida de adhesión ≤ GT1 (más del 95% permanece en la superficie)
T-Bend EN 13523-7
Doblado a 180º sobre muestra plana en temple H44 Mínimo T ≥ 1,5 (doblado 4 veces)
SIN GRIETAS Resistencia a la niebla salina EN 13523-8
1000 horas de ensayo Clase 2 (según la NORMA EN 1396, tabla C4)
QV-B Test EN 13523-10
1000 horas de ensayo (500h de QV-B) Ligeros cambios de color y
pérdida de brillo ≤ 10% Resistencia MEK EN 13523-11
≤80 pasadas dobles
Resistencia a la humedad ASTM D2247-68
Después de 1000 horas de ensayo SIN INFLUENCIA
PVdF 2 layers Coating thickness EN 13523-1
25µ paint (-4µ / +4µ) 70% Kynar 500
Specular gloss topcoat EN 13523-2
Gloss measured by 60º Gardner: 30 g.u. (tolerances according NORM EN 1396, table 4)
Pencil hardness EN 13523-4
≥HB
Adhesion to cracking on rapid deformation EN 13523-5
Reverse impact resistance measures by 7,5 [Nm/mm] NO CRACKS
Adhesion to cracking on rapid deformation after indentation EN 13523-6
Loss of adhesion ≤ GT1 (more than 95% remains on the surface)
Resistance to cracking on bending EN 13523-7
Bending through 180º on flat material up to temper H44 Minimum T ≥ 1,5 (bending 4 times)
NO CRACKS Resistance to salt acid spray fog EN 13523-8
After 1000 hours testing Corrosion index 2 (according NORM EN 1396, table C4)
QV-B Test EN 13523-10
After 1000 test hours (500 hours UV-B test) Slight color change allowed and
gloss reduction ≤ 10% M.E.K / Solvent rubbing test EN 13523-11
≤80 double rubs
Humidity resistance ASTM D2247-68
After 1000 hours testing NO INFLUENCE
Polígono Industrial de Bayas. C/ Ircio. Parcelas R72-77 - 09200 Miranda de Ebro, Burgos. SPAIN Tel.: +34 947 333 320 - Fax: +34 947 324 913 - [email protected] - www.alucoil.com
CABEBA
PVdF BICAPA COASTAL Espesor de pintura EN 13523-1
31µ (-4µ / +4µ) 70% Kynar 500
Brillo especular EN 13523-2
Brillo medido a 60º Gardner: 30 g.u. (tolerancias según la NORMA EN 1396, tabla 4)
Dureza, método del lápiz EN 13523-4
≥HB
Adherencia EN 13523-5
Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS
Adherencia & Impacto EN 13523-6
Pérdida de adhesión ≤ GT1 (más del 95% permanece en la superficie)
T-Bend EN 13523-7
Doblado a 180º sobre muestra plana en temple H44 Mínimo T ≥ 1,5 (doblado 4 veces)
SIN GRIETAS Resistencia a la niebla salina EN 13523-8
1000 horas de ensayo Clase 3 (según la NORMA EN 1396, tabla C4)
QV-B Test EN 13523-10
1000 horas de ensayo (500h de QV-B) Ligeros cambios de color y
pérdida de brillo ≤ 10% Resistencia MEK EN 13523-11
≥80 pasadas dobles
Resistencia a la humedad ASTM D2247-68
Después de 1000 horas de ensayo SIN INFLUENCIA
PVdF 2 layers COASTAL Coating thickness EN 13523-1
31µ paint (-4µ / +4µ) 70% Kynar 500
Specular gloss topcoat EN 13523-2
Gloss measured by 60º Gardner: 30 g.u. (tolerances according NORM EN 1396, table 4)
Pencil hardness EN 13523-4
≥HB
Adhesion to cracking on rapid deformation EN 13523-5
Reverse impact resistance measures by 7,5 [Nm/mm] NO CRACKS
Adhesion to cracking on rapid deformation after indentation EN 13523-6
Loss of adhesion ≤ GT1 (more than 95% remains on the surface)
Resistance to cracking on bending EN 13523-7
Bending through 180º on flat material up to temper H44 Minimum T ≥ 1,5 (bending 4 times)
NO CRACKS Resistance to salt acid spray fog EN 13523-8
After 1000 hours testing Corrosion index 3 (according NORM EN 1396, table C4)
QV-B Test EN 13523-10
After 1000 test hours (500 hours UV-B test) Slight color change allowed and
gloss reduction ≤ 10% M.E.K / Solvent rubbing test EN 13523-11
≥80 double rubs
Humidity resistance ASTM D2247-68
After 1000 hours testing NO INFLUENCE
Polígono Industrial de Bayas. C/ Ircio. Parcelas R72-77 - 09200 Miranda de Ebro, Burgos. SPAIN Tel.: +34 947 333 320 - Fax: +34 947 324 913 - [email protected] - www.alucoil.com
CABEBA
PVdF TRICAPA Espesor de pintura EN 13523-1
37µ (-6µ / +6µ) 70% Kynar 500
Brillo especular EN 13523-2
Brillo medido a 60º Gardner: 30 g.u. (tolerancias según la NORMA EN 1396, tabla 4)
Dureza, método del lápiz EN 13523-4
≥HB
Adherencia EN 13523-5
Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS
Adherencia & Impacto EN 13523-6
Pérdida de adhesión ≤ GT1 (más del 95% permanece en la superficie)
T-Bend EN 13523-7
Doblado a 180º sobre muestra plana en temple H44 Mínimo T ≥ 1 (doblado 3 veces)
SIN GRIETAS Resistencia a la niebla salina EN 13523-8
1000 horas de ensayo Clase 2 (según la NORMA EN 1396, tabla C4)
QV-B Test EN 13523-10
1000 horas de ensayo (500h de QV-B) Ligeros cambios de color y
pérdida de brillo ≤ 10% Resistencia MEK EN 13523-11
≤80 pasadas dobles
Resistencia a la humedad ASTM D2247-68
Después de 1000 horas de ensayo SIN INFLUENCIA
PVdF 3 layers Coating thickness EN 13523-1
37µ (-6µ / +6µ) 70% Kynar 500
Specular gloss topcoat EN 13523-2
Gloss measured by 60º Gardner: 30 g.u. (tolerances according NORM EN 1396, table 4)
Pencil hardness EN 13523-4
≥HB
Adhesion to cracking on rapid deformation EN 13523-5
Reverse impact resistance measures by 7,5 [Nm/mm] NO CRACKS
Adhesion to cracking on rapid deformation after indentation EN 13523-6
Loss of adhesion ≤ GT1 (more than 95% remains on the surface)
Resistance to cracking on bending EN 13523-7
Bending through 180º on flat material up to temper H44 Minimum T ≥ 1 (bending 3 times)
NO CRACKS Resistance to salt acid spray fog EN 13523-8
After 1000 hours testing Corrosion index 2 (according NORM EN 1396, table C4)
QV-B Test EN 13523-10
After 1000 test hours (500 hours UV-B test) Slight color change allowed and
Gloss reduction ≤ 10% M.E.K / Solvent rubbing test EN 13523-11
≤80 double rubs
Humidity resistance ASTM D2247-68
After 1000 hours testing NO INFLUENCE
Polígono Industrial de Bayas. C/ Ircio. Parcelas R72-77 - 09200 Miranda de Ebro, Burgos. SPAIN Tel.: +34 947 333 320 - Fax: +34 947 324 913 - [email protected] - www.alucoil.com
CABEBA
HQPE Espesor de pintura EN 13523-1
23µ (-4µ / +4µ)
Brillo especular EN 13523-2
Brillo medido a 60º Gardner: 10-80 g.u. (tolerancias según la NORMA EN 1396, tabla 4)
Dureza, método del lápiz EN 13523-4
≥F
Adherencia EN 13523-5
Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS
Adherencia & Impacto EN 13523-6
Pérdida de adhesión ≤ GT1 (más del 95% permanece en la superficie)
T-Bend EN 13523-7
Doblado a 180º sobre muestra plana en temple H44 Mínimo T ≥ 1,5 (doblado 4 veces)
SIN GRIETAS Resistencia a la niebla salina EN 13523-8
1000 horas de ensayo Clase 2 (según la NORMA EN 1396, tabla C4)
QV-B Test EN 13523-10
500 horas de ensayo (250h de QV-B) Ligeros cambios de color y
pérdida de brillo ≤ 50% Resistencia MEK EN 13523-11
≤80 pasadas dobles
Resistencia a la humedad ASTM D2247-68
Después de 1000 horas de ensayo SIN INFLUENCIA
HQPE Coating thickness EN 13523-1
23µ paint (-4µ / +4µ)
Specular gloss topcoat EN 13523-2
Gloss measured by 60º Gardner: 10-80 g.u. (tolerances according NORM EN 1396, table 4)
Pencil hardness EN 13523-4
≥F
Adhesion to cracking on rapid deformation EN 13523-5
Reverse impact resistance measures by 7,5 [Nm/mm] NO CRACKS
Adhesion to cracking on rapid deformation after indentation EN 13523-6
Loss of adhesion ≤ GT1 (more than 95% remains on the surface)
Resistance to cracking on bending EN 13523-7
Bending through 180º on flat material up to temper H44 Minimum T ≥ 1,5 (bending 4 times)
NO CRACKS Resistance to salt acid spray fog EN 13523-8
After 1000 hours testing Corrosion index 2 (according NORM EN 1396, table C4)
QV-B Test EN 13523-10
After 500 test hours (250 hours UV-B test) Slight color change allowed and
Gloss reduction ≤ 50% M.E.K / Solvent rubbing test EN 13523-11
≤80 double rubs
Humidity resistance ASTM D2247-68
After 1000 hours testing NO INFLUENCE
Polígono Industrial de Bayas. C/ Ircio. Parcelas R72-77 - 09200 Miranda de Ebro, Burgos. SPAIN Tel.: +34 947 333 320 - Fax: +34 947 324 913 - [email protected] - www.alucoil.com
CABEBA
FEVE BICAPA
Espesor de pintura EN 13523-1
27µ (-2µ / +2µ)
Brillo especular EN 13523-2
Brillo medido a 60º Gardner: 10-85 g.u. (tolerancias según la NORMA EN 1396, tabla 4)
Dureza, método del lápiz EN 13523-4
≥ F
Adherencia EN 13523-5
Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS
Adherencia & Impacto EN 13523-6
Pérdida de adhesión ≤ GT1 (más del 95% permanece en la superficie)
T-Bend EN 13523-7
Doblado a 180º sobre muestra plana en temple H44 Mínimo T ≥ 1,5 (doblado 4 veces)
SIN GRIETAS Resistencia a la niebla salina EN 13523-8
1000 horas de ensayo Clase 3 (según la NORMA EN 1396, tabla C4)
QV-B Test EN 13523-10
1000 horas de ensayo (500h de QV-B) Ligeros cambios de color y
pérdida de brillo ≤ 10% Resistencia MEK EN 13523-11
≤ 80 pasadas dobles
Resistencia a la humedad ASTM D2247-68
Después de 1000 horas de ensayo SIN INFLUENCIA
FEVE 2 LAYERS
Coating thickness EN 13523-1
27µ (-2µ / +2µ)
Specular gloss topcoat EN 13523-2
Gloss measured by 60º Gardner: 10-85 g.u. (tolerances according NORM EN 1396, table 4)
Pencil hardness EN 13523-4
≥ F
Adhesion to cracking on rapid deformation EN 13523-5
Reverse impact resistance measures by 7,5 [Nm/mm] NO CRACKS
Adhesion to cracking on rapid deformation after indentation EN 13523-6
Loss of adhesion ≤ GT1 (more than 95% remains on the surface)
Resistance to cracking on bending EN 13523-7
Bending through 180º on flat material up to temper H44 Minimum T ≥ 1,5 (bending 4 times)
NO CRACKS Resistance to salt acid spray fog EN 13523-8
After 1000 hours testing Corrosion index 3 (according NORM EN 1396, table C4)
QV-B Test EN 13523-10
After 1000 test hours (500 hours UV-B test) Slight color change allowed and
Gloss reduction ≤ 10% M.E.K / Solvent rubbing test EN 13523-11
≤ 80 double rubs
Humidity resistance ASTM D2247-68
After 1000 hours testing NO INFLUENCE
Polígono Industrial de Bayas. C/ Ircio. Parcelas R72-77 - 09200 Miranda de Ebro, Burgos. SPAIN Tel.: +34 947 333 320 - Fax: +34 947 324 913 - [email protected] - www.alucoil.com
CABEBA
MIRROR SILVER ARCHITECTURE FE 1G
Propiedades Mecánicas del Aluminio EN 6892-1
Límite elástico, Rp0.2 > 140MPa Carga a la rotura, Rm > 120 MPa
Alargamiento, A > 1% Espesor de la laca EN 13523-1
11(-2µ / +2µ)
Brillo especular EN 13523-2
Brillo medido a 60º Gardner: > 80 g.u. (tolerancias según la NORMA EN 1396, tabla 4)
Dureza, método del lápiz EN 13523-4
≥ HB
Adherencia EN 13523-5
Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS
Adherencia & Impacto EN 13523-6
Pérdida de adhesión ≤ GT1 (más del 95% permanece en la superficie)
T-Bend EN 13523-7
Doblado a 180º sobre muestra plana en temple H44 Mínimo T ≥ 4
SIN GRIETAS Resistencia a la niebla salina EN 13523-8
1000 horas de ensayo Clase 2 (según la NORMA EN 1396, tabla C4)
QV-B Test EN 13523-10
1000 horas de ensayo (500h de QV-B) Ligeros cambios de color y
pérdida de brillo ≤ 10% Resistencia MEK EN 13523-11
≥100 pasadas dobles
Resistencia a la humedad ASTM D2247-68
Después de 1000 horas de ensayo SIN INFLUENCIA
Cualquier tipo de manipulación del material, durante el transporte, manipulación, instalación e incluso, después de la instalación, puede producir marcas y bollos en la superficie, que no se aprecian en otro tipo de acabados, pero que, debido al alto brillo y reflexión de este material, no se pueden evitar.
MIRROR SILVER ARCHITECTURE FE 1G
Aluminium Mechanical Properties EN 6892-1
Tensile strength, Rp0.2 > 140MPa
Yield strength, Rm> 120 MPa Elongation, A > 1%
Coating Thickness EN 13523-1
11(-2µ / +2µ)
Specular gloss topcoat EN 13523-2
Gloss measured by 60º Gardner: > 80 g.u. (tolerances according NORM EN 1396, table 4)
Pencil hardness EN 13523-4
≥ HB
Adhesion to cracking on rapid deformation EN 13523-5
Reverse impact resistance measures by 7,5 [Nm/mm] NO CRACKS
Adhesion to cracking on rapid deformation after indentation EN 13523-6
Loss of adhesion ≤ GT1 (more than 95% remains on the surface)
Resistance to cracking on bending EN 13523-7
Bending through 180º on flat material up to temper H44 Minimum T ≥ 4
NO CRACKS Resistance to salt acid spray fog EN 13523-8
After 1000 hours testing Corrosion index 2 (according NORM EN 1396, table C4)
QV-B Test EN 13523-10
After 1000 test hours (500 hours UV-B test) Slight color change allowed and
gloss reduction ≤ 10% M.E.K / Solvent rubbing test EN 13523-11
≥ 100 double rubs
Humidity resistance ASTM D2247-68
After 1000 hours testing NO INFLUENCE
Any kind of pressure over the surface produced during the manipulation, transport, production, installation and after creates marks and dents, witch cannot be appreciated in other matt colour finish, and that are very difficult to avoid due physical properties of the mirror finish (high gloss and reflection).
Polígono Industrial de Bayas. C/ Ircio. Parcelas R72-77 - 09200 Miranda de Ebro, Burgos. SPAIN Tel.: +34 947 333 320 - Fax: +34 947 324 913 - [email protected] - www.alucoil.com
CABEBA
MIRROR SATIN Espesor de la laca EN 13523-1
Approx. 12 micras
Brillo especular EN 13523-2
Brillo medido a 20º MIrrorMatt- Cotton Mirror 125: Approx. 740 g.u
Diferencia de color EN 13523-3
No aplicable
Dureza, método del lápiz EN 13523-4
≥ HB
Adherencia EN 13523-5
Resistencia al impacto medido en 7,5 [Nm/mm] SIN GRIETAS
Adherencia & Impacto EN 13523-6
Pérdida de adhesión ≤ GT1 (más del 95% permanece en la superficie)
T-Bend EN 13523-7
Doblado a 180º sobre muestra plana en temple H44 Mínimo T ≥ 4
SIN GRIETAS Resistencia a la niebla salina EN 13523-8
1000 horas de ensayo Clase 3 (según la NORMA EN 1396, tabla C4)
QV-B Test EN 13523-10
500 horas de ensayo (250h de QV-B) Ligeros cambios de color y
pérdida de brillo ≤ 30% Resistencia MEK EN 13523-11
≤100 pasadas dobles
Resistencia al caleo EN 13523-14
500 horas de ensayo (250h de QV-B) Caleo ≤ 10%
Resistencia a la humedad ASTM D2247-68
Después de 1000 horas de ensayo SIN INFLUENCIA
MIRROR SATIN Coating Thickness EN 13523-1
Approx. 12 micron
Specular gloss topcoat EN 13523-2
Gloss measured by 20º (coated): MIrrorMatt- Cotton Mirror 125: Approx. 740 g.u
Color differences topcoat EN 13523-3
Not applicable
Pencil hardness EN 13523-4
≥ HB
Adhesion to cracking on rapid deformation EN 13523-5
Reverse impact resistance measures by 7,5 [Nm/mm] NO CRACKS
Adhesion to cracking on rapid deformation after indentation EN 13523-6
Loss of adhesion ≤ GT1 (more than 95% remains on the surface)
Resistance to cracking on bending EN 13523-7
Bending through 180º on flat material up to temper H44 Minimum T ≥ 4 NO CRACKS
Resistance to salt acid spray fog EN 13523-8
After 1000 hours testing Corrosion index 3 (according NORM EN 1396, table C4)
QV-B Test EN 13523-10
After 500 test hours (250 hours UV-B test) Slight color change allowed and
gloss reduction ≤ 30% M.E.K / Solvent rubbing test EN 13523-11
≤ 100 double rubs
Measurement of chalking EN 13523-14
After 500 test hours (250 hours UV-B test) Chalking ≤10%
Humidity resistance ASTM D2247-68
After 1000 hours testing NO INFLUENCE
Polígono Industrial de Bayas. C/ Ircio. Parcelas R72-77 - 09200 Miranda de Ebro, Burgos. SPAIN Tel.: +34 947 333 320 - Fax: +34 947 324 913 - [email protected] - www.alucoil.com
CABEBA
MIRROR BRITE Composición de aluminio EN 573-3
99.85%
Límite de elasticidad Rp 0.2 EN 485/2
Rp 0,2 (MPa) ≥110
Resistencia a la tracción Rm EN 485/2
Rm (MPa) ≥120
Elongación A50 EN 485/2
A50 (%) ≥2
QV-B Test ASTM G53
1000 horas de ensayo (313nm) Cambios de color ∆E<1
Resistencia a la niebla salina ASTM G85
1000 horas de ensayo <2 mm media de corrosión
en mm medido en la cruz < 8 ampollas en superficie
MIRROR BRITE Aluminium Composition EN 13523-1
99.85%
Yield strenght Rp 0.2 EN 573-3
Rp 0,2 (MPa) ≥110
Tensile strength Rm EN 485/2
Rm (MPa) ≥120
Elongation A50 EN 485/2
A50 (%) ≥2
QV-B Test ASTM G53
After 1000 test hours (313nm) Colorchange ∆E<1
Resistance to salt acid spray fog ASTM G85
After 1000 test hours <2 mm average creepage from scribe
< 8 blisters in field