Novedades_BGS_Julio´11

8/6/2019 Novedades_BGS_Julio11

1/29

- - 2 reversible ratchets, 1/4" + 1/2",fine 72 tooth, ergonomic design

- sockets 1/4":4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13 und 14 mm

- sockets 1/4", extra deep:6, 7, 8, 10, 11, 12 und 13 mm

- sockets 1/2":10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 24,27, 30 und 32 mm

- 50 mm and 100 mm extension bar, 1/4"- 125 mm and 250 mm extension bar, 1/2"- 1/2" sliding handle adaptor for extension bar- sliding handle 1/4", 110 mm- universal joint 1/4" + 1/2"- 150 mm spinning handle 1/4"- bit sockets 1/4":slot 4, 5.5 und 7 mm, cross slot #1, 2 und 3,Pozi #1, 2 und 3; internal hexagon 3, 4, 5, 6, 7und 8 mmT-Star T10, T15, T20, T25, T30, T40

- with inside 1/2 " drive- one side 17, other side 19 mm hex

- for screwed connections that are hard to reach- spinning head (360) is in every position- if not adjusted, good for quick screwing

- flexible with magnetic screw and nut holder- flexible shaft made of steel, retaining sleevemade of hardned anodized aluminum alloy


2/29


3/29

- in sizes 6, 7, 8, 9, 10, 11, 12, 13 and 14 mm- external hexagon for additional force- length 230 mm

- use everywhere where precise work is requiredlike e.g. in model making, electronics etc.- T6x50 - T7x50 - T8x50 - T9x50 - T10x50 - T15x50 - T20x50

- anti slip two component handle

- with 6.3 (1/4) square drive in handle- from PRO+ tool cabinet BGS 4050


4/29

- high carbon steel blade- induction hardened teeth- 15 teeth per inch

- suitable for BGS 3268- disc diameter: 105 mm- disc thickness: 1.5 mm- hole: 16.2 mm

- Crimping tool set with ratcheting function- 2 exchangeable jaws for

- non-insulated end terminals 0,5 - 6 mm(red-blue-yellow)

- non-insulated end terminals 1,5 - 10 mmwith closed cable attachment ring

- suitable for BGS 1410 - 1411 - 1412


5/29


6/29

- VDE approved- easy to handle with non-slip grip






7/29

- chrome finish

- chrome finish

- cuts steel cable up to 5 mm- cuts also spring wire up to 1,5 mm- SK5 high cabon steel blades- length: 195 mm

- for hard to reach places such as behind interior trim,instrument panel, engine compartment, etc.

- very small even when fully opened- heavy duty 2-component plastic handle- length 350 mm

- to remove the output shaft from front axle- suitable for 4WD BMW 535IX, X3 and X5- makes disassembling much easier- handle vinyl coated


8/29

- professional, stable puller for cars, vansand small utility vehicle with bolt circle diameter120-215 mm

- especially suitable for glued or rusted axle drive shaft- pressure force of the hydraulic cylinder is 10 t,

these can be replaced by an enclosed impact spindle- quick and easy adjustment of the puller-number and diameter- suitable for all wheel hubs with 3, 4, 5, and 6 holes- hydraulic Spindle 10 t, 1 1/2" threaded ball andpressure, sliding with 17 mm hex drive, length 250 mm

- impact spindle with moving the firing pin and 30 mmhex drive, length 285 mm

- bump wrench 30 mm hex drive for spindle stroke,length 200 mm

- hydraulic pressure piece spindle extension 35 mm- centering point for hydraulic spindle- 101 mm adaptor disc for pull arms and

hydraulic spindle- 5x pull arms, length 175 mm

- for daily, professional workshop use- 4.75 mm (3 / 16 "), 5,00 mm, 6,00 mm- light weight, used directly on the vehicle- suitable for steel - aluminum, brass, - andcopper lines

- suitable for coated wires- for double and convex flare to SAE and DIN

- includes deburring tool

- for easy disassembly of the retaining spring on brake shoes- for professional daily use in workshops- suitable for spring plate diameter 14 to 20 mm- easy and safe handling- length 240 mm, diameter 34 mm


9/29

- offset open end double ring wrench, 17 mm- especially suitable for poorly accessible area- double hexagon profile- suitable for most diesel engines- chrom finish

- simplifies the assembly and disassembly- suitable for most injectors- size 25, 27, 29 und 30 mm- Siemens and Bosch nozzles- also suitable for Peugeot and Citroen 2.0 HDI Lengines (110/135 hp)

- hardened special steel for durability

- for testing the injectors of common rail engineswith up to 8 cylinders (injectors)

- determination of the runback volume viaglass tubes or measurement cartridges

- includes 8 glass tubes, 8 measurementcartridges with 70 cm connecting lines,

mounted on aluminium bar with hooks

- suitable for many Mercedes models:W107, W116, W123, W124, W126, W140 and W210

- for easy removal of the instrument panel- made from stainless steel


10/29

- professional spring compressor for daily workshop use- for springs with a diameter of 90 to 140 mm- especially suitable for vehicles with small hole in thespring controle arm down to 30 mmVW Touran, Citroen C3, Skoda Octavia, Peugeot 107

- suitable for double wishbone / multi-linksuspension system

- special-socket prevents overloading of the springcompressor

- includes:2 tensioning jaws 90 to 120 mm2 tensioning jaws 120 to 140 mmspecial spindle for limited spaces 30 mmtorque stick (safety key) for torque limited

- maximum load: 2500kg (25000 Nm)- minimum distance: 96 mmmaximum distance: 220 mmmaximum travel: 124 mm

- professional spring compressor for daily use in workshops- includes 2 spring plate pairs, universally applicablefor almost all MC Pherson struts

- maximum load: 1650 kg (16150 N)- tension: 220 mm- spindle: M 15 x 300 mm

- two sets in one:suitable for 39 mm and 41 mm front fork springs

- special socket for disassembly and assembly of fork cap- 195 mm long clamping spindle with a diameter of 18.6 mm


11/29

- facilitates assembly and disassembly- suitable for Audi A2 and Skoda Fabia 00-,VW Polo and Seat Ibiza 02-, VW Fox 05-

- for vehicles with 72 mm wheel hub- high-strength ball-bearing spindle

- pressure plate with 8 holes- 5 bolts- 2 divided shells

- suitable for all VW Polo model 2002- facilitates the removal of the rubber bushings of front axle- spindle M12 x 260 mm with 19 mm 6-pt- spindle nut with 24 mm 6-pt drive- washer made of brass to reduce friction

- universal type for all car models- also for assembly or disassembly of silent bearings,rubber- and ball bearings

- also suitable for rubber bushes and rotary shaft seals- smooth running because of high-quality ball bearingon spindle screw nut

- four 350 mm spindles in M10, M12, M14 und M16- 20 inner pressure pads in 34, 36, 38 mm bis 72 mm- 20 outer pressure pads in 44, 46, 48 mm bis 82 mm- pressure pads are slotted for visual control

- for pressure hose BGS 3066 andgrease guns BGS 3236, 3065, 3140, 3141

- thread: 1/8 "PT


12/29

- 12 Volt- NI-CD

- it is possible to weld and hammer simultaneously- handle with connector for electrical connection towelding equipment

- pull out dents without drilling holes in the body- chrome-plated carbon steel- weight 1.6 kg

- with holding teeth- 2 pcs. shells for a perfect fit of the abrasive

- for repairing of dents e.g. hail damages, door bumps, etc.- allows repair of dents without painting- no need to disassemble car body parts- disassembly of panels is rarely necessary- repair costs can be kept low, no painting cost- set consists of all bumping tools neededin various lengths and shapes

- made of stainless and carbon steel- also contains air inflating pillow,trim strip wedge and other parts


13/29

- for rusted track rods- facilitates the track setting- special mouth mechanism for track rods from 9 up to 20 mm- detachable, knurled handle- length: 390 mm

- galvanized

- changing of the tie rod ends is possiblewithout additional alignment

- reduces the workload when changing tie rods- consists of:

- main unit with clamping device- 10 and 12 mm caliper, short and long type- 17 mm caliper for VW- fixing unit- caliper for depth measuring

- for precisely aligned mounting of the subframe- needed e.g. for replacing the rubber bushingsand all jobs for which the auxiliary frame (subframe)is removed

- suitable for:VW Scirocco (09), EOS (06), Golf (09), Golf Plus (05), Jetta (04-06),Polo (02), Fox (06), Passat (06), Passat CL (09), Audi A3 (04)and Audi A3 (04), TT (07), A4 (01)

- use like OEM T10096

- for F8Q and F9Q diesel engines with adjustable pump wheel- used in Renault Megan / Scenic / Kangoo, MitsubishiCarisma, Opel / Vauxhall Arena, Volvo S40/V40 etc.

- special socket with 27 mm hexagon and 1/2 drive- adjustable tool with 3 x 4 mm pins to adjust the pump- adapter for Bosch pumps 8 mm on 10 mm


14/29

- draws pulley by the holes without causing demage- moving legs adapt to differing pulley diameters- for different bolt patterns and suitable intervals- 8 slots for inclusion of puller- puller with 18 mm drive

- 16 mm spindle with centering ball and 24 mm drive

- will be needed for replacing the cylinder headsealing and motor timing

- suitable for the following Mini models:One, HB Cooper, Cooper, series R55-56with motor code N12

- crankshaft locking tool used as OEM 119590- camshaft locking tool used as OEM 119540- chain tensioner used as OEM 119340

- suitable for VW-Audi, Opel/Vauxhall, Ford, BMW,Mercedes, Peugeot, Citroen, Renault, Fiat andjapanese vehicles

- universally applicable by eight slots in puller flange- facilitates the removal of pulleys- needed for e.g. timing belt or water pump replacement- variable pitch circle, from 70 mm to 100 mm- 2 sets of 3 x 10 mm puller screws and 3 nuts madeof carbon steel

- pull off the pulley with spindle or mallet possible- pressure sleeve with centering made of carbon steel- 5 kg drop weight on 495 mm axis- galvanized puller flange


15/29

- suitable for Audi A4 Cabrio, A6, A8 with engine code:ASN, AVK, BBJ

- for timing belt replacement and repair work on the engine- easy mounting of the belt as camshaft and crankshaft is fixed- contains:

- 2x camshaft fixer tool (use as OEM T40030)- crankshaft fixer tool (use as OEM T40026)- tension roller key (use as OEM 3387)- socket for basic adjustment of the camshaft adjuster(use as OEM T40028)

- pins for clamping element (use as OEM 40011)

- for easy and accurate determination of the ignition TDC- especially suitable for vehicles which have no OT markings- includes:- measurement unit with magnetic holder- connecting tube with spark plug or glow plug adapterin 8 -10 -12 -14 -18 mm + universal cone adapter

- 60 and 160 mm adapter tube of aluminum for deepseated spark plug

- for engine codes: X10XE and X12XE- includes important tools for e.g.:- changing the timing chain and other jobs on the valve train

- working on the intake and exhaust camshafts- fixing the crankshaft- suitable for the following models:Agila, Corsa 1.0 12V and 1.2 16V


16/29

- allows damage free mounting of flexible multi-ribbed belts- flexible belt drive requires no idler,but this special assembly assembly tool

- suitable for the following models:- BMW: 118, 120, 318, 325, 330, 335, 520, 525, 530, 535

635, 730, X3, X5 petrol and diesel engine- Chrysler Grand Voyager, Voyager- Citroen: C2, C3, C4, Jumper, Relay- Fiat Albea, Doblo, Marea, Multipla, Ducato, Fiorino,Fiorino Qubo, Linea, Palio, Siena, Stilo,Strada Pick Up, Lancia: Lybra

- Ford C-Max, Focus, Mondeo, Tourneo, Transit, Courier, Fiesta, Fusion- Iveco Daily- Mazda 3, 5, Axela- Peugeot: 206, 207, 307, Boxer- VOLVO: C30, S40, V50

- contains 3 different special tools

- heavy duty finish- from 450 to 760 mm adjustable in length- head adjustable in 10 positions- ideal for work when you need flexibility

- for VAG 1,9 and 2.0l TDI with (use as OEM VAG T10050)

- includes:- crankshaft locking tool- locking bolt for pump- locking plate for idler

- for VAG 2.0L TDI and some 1,9L

(use as VAG OEM T10100)


17/29

- suitable for Renault engines 1.5 L, 1.9 L, 2.2 L, 2.5 dCI- also suitable for the identic engines in Nissan, Opel and Dacia- 27 mm x 12-pt cup also suitable for MB A-Class- 96 mm x 18-pt cup also fits Audi A4, A6 TDI and VW Passat TDI

- suitable for Alfa Romeo, Fiat and Lancia- for oil filter, oil filler and oil drain plugson the transmission, differential

- angled key 40 and 90 - length: 283 mm

- for daily use in workshops- 4 square sockets: 8 - 10 mm und 3/8" - 1/2"- 4 hex. sockets: 10 - 12 - 14 - 17 mmoverall length: 270 mm

- heavy duty tool with duplex chain- chain width approx. 22 mm- handle satin chrome finished- claw prevents slipping- 180 swivel handle- ease to use due to special chain-lock- suitable for oil filters 60-160 mmlength 520 mm


18/29

- suitable for daily workshops use- a clean oil change is possible by suction- usable for engine, transmission, rear axle oiland other non-corrosive liquids

- suction hose diameter in 9.8 - 8.0 - 6.7 - 4.5 mm

for suction through the dipstick tube- 7.5 l container with base ensures stability, toaccommodate large amounts of oil

- suitable for oil extraction at all smart models butalso for all other vehicles for which an oil change is to beperformed without using a lift

- with a special si licone brake breather hose with avalve for one-hand operation

- easy brake bleeding on brake systems on all vehicles- the built-in hand vacuum pump allows brake bleedingeven without compressed air

- suitable for 2- and 4-stroke motorcycle engine

- original spare parts


19/29

- professional tool for daily use in workshops- the optical density testing of battery acid,antifreeze activity (ethylene) and measurement ofAdBlue / AUS32

- easy reading

- adjustable ocular- accuracy + / - 5%- dimensions 142x32x40 mm

- for removal of glued wheel balancing weights on

aluminium wheel rims

- suitable for new kind of hose clamp, as built into theVAG 2.0 TDI

- due to bowden cable also suitable for tight spaces- hose clamp lock with release button


20/29

- for gentle loosening groove nuts- suitable at e.g. bearing nut- 1/2" drive, length 60 mm

all dimensions in mm

inside D2 outside D1 tooth wide ZB tooth lenght ZL15,5 22,0 3,3 5,818,5 26,0 3,8 5,821,5 30,0 4,3 5,825,0 33,0 4,0 4,827,5 37,0 4,8 4,833,5 44,0 5,3 4,838,5 50,0 5,8 3,844,5 56,0 5,8 3,850,5 63,0 6,3 3,855,5 69,0 6,8 2,861,5 75,0 6,8 2,9

- for gentle loosening groove nuts- suitable at e.g. bearing nut- 1/2" drive, length 60 mm

all dimensions in mminside D2 outside D1 tooth wide ZB tooth lenght ZL20,0 26,0 2,8 2,523,5 31,0 2,8 3,026,5 34,0 3,8 2,529,5 38,0 4,8 2,534,5 42,0 3,8 3,5

40,5 50,0 4,8 3,546,5 58,0 4,8 4,059,5 75,0 5,8 4,565,8 82,0 5,8 5,071,8 88,0 5,6 5,0

- in sizes:

5 - 6 - 7 - 8 - 9 - 10 - 10,5 - 11 - 12 - 14 and 16 mm


21/29

- especially suitable for pipeline fittings- no widening because foot has special profile- sizes 12,14,16, 17,18 and 19 mm with 1/2 "drive- angled, slotted socket with double hexagon- length: 98 mm

- length: 250 mm

- slotted, angled head with hexagon and double hexagon drive- chrom finish

- suitable for Peugeot, Renault, etc., with HDI engine- 3/8" drive

- for filter caps with 108 mm with 46 grooves

- wrench for assembly and disassembly of turbo-chargers- facilitates assembly of hard to reach screws- 12 mm hex wrench with 12-pt and 3/8" drive- depth 85 mm, length 99 mm


22/29

- for losening the upper shock absorber screwing- the recess in the front part of the pin wrench allowscounterholding the piston rod

- plastic coated blade prevents damage- suitable for Mercedes Benz 211 T-Model rear axle (E-Class Station

Wagon)- for nuts with 3-pin adapter

- contains all tools for fittings on air conditioning systems- a useful supplement for item 8036- special sockets for 2.2 and 3.2 mm fixed throttles- 2 special 8-pt. sockets 12 and 15 mm- TS-(5-Star-Profil) bits to loosen flanges etc:TS10, TS15, TS20, TS25, TS27, TS30 und TS40

- for quick and easy separating of gasoline quick locks- suitable for quick-on fuel filters and similar connections

that are separated by pressure on the outer ring- pliers is electroplated- handle dip coated

- suitable for outside mirror of BMW models:E12, E21, E23, E24, E28, E30, E31, E32, E34,E36, E38 and E39

- removal is very difficult without these pliers- with spring mechanism and stop setting- made of carbon steel

- dip-coated handles


23/29

- simplifies the assembly and disassembly of oil cooler- holding forks bolted- holding fork at 15 and 22 mm- adjustable distance (like water pump pliers)

- for dismantling of shaft gasket- quick and easy disassembly with 320 mm lever- torsion lever adjustable in five positions of up to 45- long life due to hardened lever- coated handle

- facilitates the insertion of valves

- automatic direction change- for use with fine grinding paste- with 8 mm shank- working speed min. 1000 rpm, max. 1250 rpm- 2 different suction plates in 18 mm and 24 mm- 13 mm shaft for attaching the suction cups

- ideal for measuring the piston ring tolerance- 0,03 - 0,04 - 0,05 - 0,06 - 0,10 - 0,15 - 0,25 - 0,30 - 0,50 mm- in bag


24/29

- for assembling and disassembling of engines,gearboxes and rear axle

- lateral and tilt adjustable head plate, thereforeespecially suitable for mounting of automatic transmission

- height approx. 880 to 1770 mm

- 4 ball bearing caster wheels- compact construction, lightweight- long lifting range- fast lifting due to hydraulic foot pedal- heavy duty- weight: 80 kg

- facilitates the transport of wheels- max. wheel weight 68 Kg


25/29

- engine crane for lifting engines and other heavy loads- lifting arm can be adjusted in 4 positions of different length- technical data:

capacity Position 1: 1000Kgcapacity Position 2: 750kg

capacity Position 3: 500Kgcapacity Position 4: 250kgmaximum height in position 1: 2019 mmmaximum height in position 4: 2248 mmlength of the lifting arm in position 1: 902 mmlength of the lifting arm in position 2: 1003 mmlength of the lifting arm in position 3: 1080 mmlength of the lifting arm in position 4: 1169 mmheight of frame: 160 mmframe length: 1257 mmoverall height: 1400 mmwidth of the frame max.: 953 mmdistance between rear and center: 597 mm

- 3 shelves with strong magnet- individually attachable- sticks to all metal surfaces- perfect storage box for tools, aerosol cans and other tools- sizes:

- 150 x 120 mm, max. load capacity 0.60 kg- 210 x 120 mm, max. load capacity 0.77 kg- 310 x 120 mm, max. load capacity 1.17 kg

- for installing and removing glow plugs- suitable for diesel engines VW, Audi, Renault- for glow plugs between engine and diesel injector pump- head with double-hexagon profile- 8 mm for operation of conductor rail screw- 12 mm for operation of glow plugs- length: 300 mm


26/29

- simplifies the assembly and disassembly andprofessional repair of glow plug thread

- suitable for most injectors- assembly and disassembly of glow plugs andrepair glow plug thread

- Extractor for fixed glow- step drill to drill damagedglow plug 7x5,5 mm and 9x5,5 mm

- taps M8x1,0, 10x1,0 and1/4"-28UNF for repairing the glow plug thread

- tap holder- E10 socket

- very robust, suitable for daily use in workshops- handy and well balanced- drive: 12.5 (1/ 2)- peak torque after 15 sec. 1110 Nm

- Level 1: 200 Nm- Level 2: 610 Nm- Level 3: 880 Nm

- air consumption: min 139 l / min- working pressure: 6.2 bar- connector: 6,3 (1/4)- hose inside diameter (recommended): 10 mm

- suitable for cartridges & bags- perfect adjusting thanks to 2 valves- very handy with wide adjustable range- applications are: windows replacements, car body repair,

installation of plastic parts and carpets, truck bodies,and many more apllications in construction and industry

- appropriate repair materials: sealants, adhesives,caulking, shock-absorbing bonding and seam sealing materials

- standard tube size: 50 mm x 236 mm- cartridge capacity: 310 ml or bag capacity: 310-400 ML- air pressure: 45-90 PSI (3,1 to 6,2 BAR)- air consumption: 5 CFM (141,5 l / min)

- air inlet: 1/4"- hose size: 1/4"- length: 370 mm (14-9/16")- weight: 1.21 kg (2,67 lbs)


27/29

- adjustable spray pattern- for 1/4 "air hose- 1,0 to 3,5 bar- various accessories:

- nozzle holder

- hose- tanks

- quick release for faster and easier change of working heads

- 3 tools in one- 12.5 (1/2) air ratchet- drilling maschine- air grinder with 6 mm shank

- incl. chuck- working pressure: 6.3 bar- air connection: 1/4"- quick air coupling

- CR2032 standard battery

- for loosening stuck wheel nut sockets on trucks and vans- maximum torque 3200 Nm- gear ratio 1:56


28/29

- includes all important parts for repair

- white- Nylon

- color-coded fuses by size- each 12 pieces: 3 - 5 - 7.5 - 10 - 15 - 20 - 25 and 30 Ampere- incl. fuse puller

- perfect for DIY and garage- especially for automotive applications- fast repair, protects cables from humidity and corrosion- shrink ratio 2:1


29/29

- 3,5 Digits LCD- low battery indication- overload protection- manual range- safety sockets and plugs

- range:- DC Voltage 200 mV, 2000 mV, 20 V, 200 V, 250 V- AC Voltage 200 V, 250 V- DC Current 20 A, 200 A, 20 mA, 200 mA, 2000 mA, 10 A- resistance 2000 Ohm, 20 kOhm, 200 kOhm, 2000 kOhm- audible continuity sounds under 50 Ohm- diode test with read forward voltage

- to spray all color and colorless paint

- independent from air compressor- adjustable spray pattern- 1000 cm reservoir for color- viscosity test cup- 150 mm spray nozzle adapter- 1800 mm connecting cable- 2x additional spray nozzle in 0.5 mm and0.8 mm and 1x spray nozzle valve

Novedades_BGS_Julio´11

Documents

Transcript of Novedades_BGS_Julio´11