KEBU6860-10 S Rodillo

8/10/2019 KEBU6860-10 S Rodillo

http://slidepdf.com/reader/full/kebu6860-10-s-rodillo 1/14

®© 2010 CaterpillarAll Rights Reserved

SAFETYOperation and MaintenanceManual Excerpt

8/10/2019 KEBU6860-10 S Rodillo


KEBU6860-10June 2003

Operation andMaintenance

ManualCP-563C and CS-563C VibratoryCompactors

4KN1-Up (Machine)4LN1-Up (Machine)

5JN1-Up (Machine)5KN1-Up (Machine)

8/10/2019 KEBU6860-10 S Rodillo


i01658146

Important Safety InformationMost accidents that involve product operation, maintenance and repair are caused by failure toobserve basic safety rules or precautions. An accident can often be avoided by recognizing potentiallyhazardous situations before an accident occurs. A person must be alert to potential hazards. Thisperson should also have the necessary training, skills and tools to perform these functions properly.

Improper operation, lubrication, maintenance or repair of this product can be dangerous andcould result in injury or death.

Do not operate or perform any lubrication, maintenance or repair on this product, until you haveread and understood the operation, lubrication, maintenance and repair information.

Safety precautions and warnings are provided in this manual and on the product. If these hazardwarnings are not heeded, bodily injury or death could occur to you or to other persons.

The hazards are identified by the “Safety Alert Symbol” and followed by a “Signal Word” such as“DANGER”, “WARNING” or “CAUTION”. The Safety Alert “WARNING” label is shown below.

The meaning of this safety alert symbol is as follows:

Attention! Become Alert! Your Safety is Involved.

The message that appears under the warning explains the hazard and can be either written orpictorially presented.

Operations that may cause product damage are identified by “NOTICE” labels on the product and inthis publication.

Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Thewarnings in this publication and on the product are, therefore, not all inclusive. If a tool, procedure,work method or operating technique that is not specifically recommended by Caterpillar is used,you must satisfy yourself that it is safe for you and for others. You should also ensure that theproduct will not be damaged or be made unsafe by the operation, lubrication, maintenance orrepair procedures that you choose.

The information, specifications, and illustrations in this publication are on the basis of information thatwas available at the time that the publication was written. The specifications, torques, pressures,measurements, adjustments, illustrations, and other items can change at any time. These changes canaffect the service that is given to the product. Obtain the complete and most current information beforeyou start any job. Caterpillar dealers have the most current information available.

When replacement parts are required for thisproduct Caterpillar recommends using Caterpil-lar replacement parts or parts with equivalentspecifications including, but not limited to, phys-ical dimensions, type, strength and material.

Failure to heed this warning can lead to prema-ture failures, product damage, personal injury or

death.

8/10/2019 KEBU6860-10 S Rodillo


6Safety SectionSafety Messages

Safety Section

i01924258

Safety Messages

SMCS Code: 7000; 7405

There are several specific safety messages on yourmachine. The exact location of the safety messagesand the description of the hazard are reviewed inthis section. Please take the time in order to becomefamiliar with the safety messages.

Make sure that you can read all of the safetymessages. Clean the safety messages. Replace thesafety messages if you cannot read the words onthe safety messages. Replace the safety messagesif you cannot view the pictures on the safety

messages.

If a safety message is damaged or missing, thesafety message must be replaced. If a safetymessage cannot be read, the safety message mustbe replaced. If a safety message is located on apart that has been replaced, a new safety messagemust be placed on the new part. Consult yourCaterpillar dealer for new safety messages.

Do not operate this machine unless you have readand understand the instructions and warnings inthe Operation and Maintenance Manual.

Failure to follow the instructions or heed the warn-ings could result in injury or death.

Contact any Caterpillar dealer for replacementmanuals. Proper care is your responsibility.

g00330005Illustration 2

The safety message is located on the operatorconsole.

No clearance for a man in this area when the ma-chine turns. Severe injury or death from crushingcould occur.

Install the steering frame lock pin into the lockedposition before lifting the machine, transportingthe machine on another vehicle, or performing ser-vice near the center of the machine.

Disengage the steering lock pin from articulationjoint and store in retainer before resuming opera-tion or the machine will not steer.


The safety message is located in the steer pivot onthe right side of the machine and on the left side

of the machine.

Improper jump start cable connections can causean explosion resulting in personal injury.

Batteries may be located in separate compart-ments. When using jump start cables, alwaysconnect the positive (+) to the positive (+) termi-nal of the battery that is connected to the startersolenoid and the negative (−) cable from thesource to the negative (−) terminal of the starter.(If the machine is not equipped with a starter

negative terminal, connect the negative (−

) cableto the engine block.) Follow the procedure in theOperation and Maintenance Manual.

8/10/2019 KEBU6860-10 S Rodillo


7Safety Section

General Hazard Information


The safety message is located on the right support.The support is located in the radiator compartment.

Structural damage, an overturn, modification, al-teration, or improper repair, can impair this struc-ture’s capability, thereby voiding this certification.Do not weld on or drill holes in the structure. Con-sult your Caterpillar dealer to determine the struc-ture’s limitations without voiding the certification.


The safety message is located on machines thatare equipped with cabs.

The protection offered by this ROPS will be im-paired if the ROPS has been subjected to any mod-ification, structural damage, or has been involvedin an overturn accident. This ROPS must be re-placed after a roll-over. Seat belts must be wornwhile operating the vehicle.


The safety message is located on the ROPS. Thesafety message is located on machines that are notequipped with a cab.

i01426767


SMCS Code: 7000


Attach a “Do Not Operate” warning tag or a similarwarning tag to the start switch or to the controlsbefore you service the equipment or before yourepair the equipment. These warning tags (SpecialInstruction, SEHS7332) are available from your

Caterpillar dealer.

Know the width of your equipment in order tomaintain proper clearance when you operate theequipment near fences or near boundary obstacles.

Be aware of high voltage power lines and powercables that are buried. If the machine comes incontact with these hazards, serious injury or deathmay occur from electrocution.

8/10/2019 KEBU6860-10 S Rodillo


8Safety SectionGeneral Hazard Information


Wear a hard hat, protective glasses, and otherprotective equipment, as required.

Do not wear loose clothing or jewelry that can snagon controls or on other parts of the equipment.

Make sure that all protective guards and all coversare secured in place on the equipment.

Keep the equipment free from foreign material.Remove debris, oil, tools, and other items from thedeck, from walkways, and from steps.

Secure all loose items such as lunch boxes, tools,and other items that are not a part of the equipment.

Know the appropriate work site hand signals and

the personnel that are authorized to give the handsignals. Accept hand signals from one person only.

Do not smoke when you service an air conditioner.Also, do not smoke if refrigerant gas may bepresent. Inhaling the fumes that are released from aflame that contacts air conditioner refrigerant cancause bodily harm or death. Inhaling gas from airconditioner refrigerant through a lighted cigarettecan cause bodily harm or death.

Never put maintenance fluids into glass containers.Drain all liquids into a suitable container.

Obey all local regulations for the disposal of liquids.

Use all cleaning solutions with care. Report allnecessary repairs.

Do not allow unauthorized personnel on theequipment.

Unless you are instructed otherwise, performmaintenance with the equipment in the servicingposition. Refer to Operation and MaintenanceManual for the procedure for placing the equipmentin the servicing position.

Pressure Air and Water

Pressurized air and/or water can cause debrisand/or hot water to be blown out. This could resultin personal injury.

When pressure air and/or pressure water is usedfor cleaning, wear protective clothing, protectiveshoes, and eye protection. Eye protection includesgoggles or a protective face shield.

The maximum air pressure for cleaning purposesmust be below 205 kPa (30 psi). The maximumwater pressure for cleaning purposes must bebelow 275 kPa (40 psi).

Trapped Pressure

Pressure can be trapped in a hydraulic system.Releasing trapped pressure can cause suddenmachine movement or attachment movement. Usecaution if you disconnect hydraulic lines or fittings.High pressure oil that is released can cause a hoseto whip. High pressure oil that is released cancause oil to spray. Fluid penetration can causeserious injury and possible death.

Fluid Penetration

Pressure can be trapped in the hydraulic circuitlong after the engine has been stopped. Thepressure can cause hydraulic fluid or items suchas pipe plugs to escape rapidly if the pressure is

not relieved correctly.

Do not remove any hydraulic components or partsuntil pressure has been relieved or personal injurymay occur. Do not disassemble any hydrauliccomponents or parts until pressure has beenrelieved or personal injury may occur. Refer to theService Manual for any procedures that are requiredto relieve the hydraulic pressure.


8/10/2019 KEBU6860-10 S Rodillo


9Safety Section


Always use a board or cardboard when you checkfor a leak. Leaking fluid that is under pressure canpenetrate body tissue. Fluid penetration can causeserious injury and possible death. A pin hole leakcan cause severe injury. If fluid is injected into yourskin, you must get treatment immediately. Seek

treatment from a doctor that is familiar with this typeof injury.

Containing Fluid Spillage

Care must be taken in order to ensure that fluidsare contained during performance of inspection,maintenance, testing, adjusting and repair of theequipment. Prepare to collect the fluid with suitablecontainers before opening any compartment ordisassembling any component containing fluids.

Refer to Special Publication, NENG2500, “Tools andShop Products Guide” for the following items:

• Tools that are suitable for collecting fluids andequipment that is suitable for collecting fluids

• Tools that are suitable for containing fluids andequipment that is suitable for containing fluids

Obey all local regulations for the disposal of liquids.

Asbestos Information


Caterpillar equipment and replacement parts thatare shipped from Caterpillar are asbestos free.Caterpillar recommends the use of only genuineCaterpillar replacement parts. Use the followingguidelines when you handle any replacement partsthat contain asbestos or when you handle asbestosdebris.

Use caution. Avoid inhaling dust that might begenerated when you handle components thatcontain asbestos fibers. Inhaling this dust canbe hazardous to your health. The componentsthat may contain asbestos fibers are brake pads,brake bands, lining material, clutch plates, and

some gaskets. The asbestos that is used in thesecomponents is usually bound in a resin or sealed insome way. Normal handling is not hazardous unlessairborne dust that contains asbestos is generated.

If dust that may contain asbestos is present, thereare several guidelines that should be followed:

• Never use compressed air for cleaning.

• Avoid brushing materials that contain asbestos.

• Avoid grinding materials that contain asbestos.

• Use a wet method in order to clean up asbestosmaterials.

• A vacuum cleaner that is equipped with a highefficiency particulate air filter (HEPA) can also beused.

• Use exhaust ventilation on permanent machiningjobs.

• Wear an approved respirator if there is no otherway to control the dust.

• Comply with applicable rules and regulations

for the work place. In the United States, useOccupational Safety and Health Administration(OSHA) requirements. These OSHA requirementscan be found in “29 CFR 1910.1001”.

• Obey environmental regulations for the disposalof asbestos.

• Stay away from areas that might have asbestosparticles in the air.

8/10/2019 KEBU6860-10 S Rodillo


10Safety SectionCrushing Prevention and Cutting Prevention

Dispose of Waste Properly


Improperly disposing of waste can threaten theenvironment. Potentially harmful fluids should be

disposed of according to local regulations.

Always use leakproof containers when you drainfluids. Do not pour waste onto the ground, down adrain, or into any source of water.

i01359664

Crushing Prevention andCutting Prevention

SMCS Code: 7000

Support the equipment properly before you performany work or maintenance beneath that equipment.Do not depend on the hydraulic cylinders to holdup the equipment. Equipment can fall if a control ismoved, or if a hydraulic line breaks.

Do not work beneath the cab of the machine unlessthe cab is properly supported.

Unless you are instructed otherwise, never attemptadjustments while the machine is moving or whilethe engine is running.

Never jump across the starter solenoid terminals

in order to start the engine. Unexpected machinemovement could result.

Whenever there are equipment control linkages theclearance in the linkage area will change with themovement of the equipment or the machine. Stayclear of areas that may have a sudden change inclearance with machine movement or equipmentmovement.

Stay clear of all rotating and moving parts.

If it is necessary to remove guards in order toperform maintenance, always install the guardsafter the maintenance is performed.

Keep objects away from moving fan blades. Thefan blade will throw objects or cut objects.

Do not use a kinked wire cable or a frayed wirecable. Wear gloves when you handle wire cable.

When you strike a retainer pin with force, theretainer pin can fly out. The loose retainer pin caninjure personnel. Make sure that the area is clearof people when you strike a retainer pin. To avoidinjury to your eyes, wear protective glasses whenyou strike a retainer pin.

Chips or other debris can fly off an object whenyou strike the object. Make sure that no one can beinjured by flying debris before striking any object.

i01329099

Burn Prevention

SMCS Code: 7000

Do not touch any part of an operating engine.Allow the engine to cool before any maintenance isperformed on the engine. Relieve all pressure inthe air system, in the oil system, in the lubricationsystem, in the fuel system, or in the cooling systembefore any lines, fittings or related items aredisconnected.

Coolant

When the engine is at operating temperature, theengine coolant is hot. The coolant is also underpressure. The radiator and all lines to the heaters orto the engine contain hot coolant.

Any contact with hot coolant or with steamcan cause severe burns. Allow cooling systemcomponents to cool before the cooling system isdrained.

Check the coolant level only after the engine hasbeen stopped.

Ensure that the filler cap is cool before removingthe filler cap. The filler cap must be cool enoughto touch with a bare hand. Remove the filler capslowly in order to relieve pressure.

Cooling system conditioner contains alkali. Alkalican cause personal injury. Do not allow alkali tocontact the skin, the eyes, or the mouth.

8/10/2019 KEBU6860-10 S Rodillo


11Safety Section

Fire Prevention and Explosion Prevention

Oils

Hot oil and hot components can cause personalinjury. Do not allow hot oil to contact the skin. Also,do not allow hot components to contact the skin.

Remove the hydraulic tank filler cap only after theengine has been stopped. The filler cap must becool enough to touch with a bare hand. Followthe standard procedure in this manual in order toremove the hydraulic tank filler cap.

Batteries

Electrolyte is an acid. Electrolyte can causepersonal injury. Do not allow electrolyte to contactthe skin or the eyes. Always wear protective glassesfor servicing batteries. Wash hands after touchingthe batteries and connectors. Use of gloves isrecommended.

i01359795

Fire Prevention and ExplosionPrevention

SMCS Code: 7000


All fuels, most lubricants, and some coolant mixturesare flammable.

Flammable fluids that are leaking or spilled onto hotsurfaces or onto electrical components can causea fire. Fire may cause personal injury and propertydamage.

Remove all flammable materials such as fuel, oil,and debris from the machine. Do not allow anyflammable materials to accumulate on the machine.

Store fuels and lubricants in properly markedcontainers away from unauthorized persons. Storeoily rags and any flammable materials in protectivecontainers. Do not smoke in areas that are used forstoring flammable materials.

Do not operate the machine near any flame.

Exhaust shields (if equipped) protect hot exhaustcomponents from oil spray or fuel spray in case ofa break in a line, in a hose, or in a seal. Exhaustshields must be installed correctly.

Do not weld on lines or on tanks that containflammable fluids. Do not flame cut lines or tanksthat contain flammable fluid. Clean any such linesor tanks thoroughly with a nonflammable solventprior to welding or flame cutting.

Check all electrical wires daily. Repair any wires that

are loose or frayed before you operate the machine.Clean all electrical connections and tighten allelectrical connections.

Dust that is generated from repairing nonmetallichoods or nonmetallic fenders can be flammableand/or explosive. Repair such components in a wellventilated area away from open flames or sparks.

Inspect all lines and hoses for wear or fordeterioration. The hoses must be properly routed.The lines and the hoses must have adequatesupport and secure clamps. Tighten all connectionsto the recommended torque. Leaks can cause fires.


8/10/2019 KEBU6860-10 S Rodillo


12Safety SectionFire Prevention and Explosion Prevention

Use caution when you are refueling a machine. Donot smoke while you are refueling a machine. Donot refuel a machine near open flames or sparks.Always stop the engine before refueling. Fill the fueltank outdoors.


Gases from a battery can explode. Keep any openflames or sparks away from the top of a battery. Donot smoke in battery charging areas.

Never check the battery charge by placing a metalobject across the terminal posts. Use a voltmeter or

a hydrometer.

Improper jumper cable connections can causean explosion that can result in injury. Refer tothe Operation Section of this manual for specificinstructions.

Do not charge a frozen battery. This may causean explosion.

Fire Extinguisher

Make sure that a fire extinguisher is available. Be

familiar with the operation of the fire extinguisher.Inspect the fire extinguisher and service the fireextinguisher regularly. Obey the recommendationson the instruction plate.

Ether

Ether is flammable and poisonous.

Use ether in well ventilated areas. Do not smokewhile you are replacing an ether cylinder or whileyou are using an ether spray.

Do not store ether cylinders in living areas or in theoperator compartment of a machine. Do not storeether cylinders in direct sunlight or in temperaturesabove 49 C (120 F). Keep ether cylinders awayfrom open flames or sparks.

Dispose of used ether cylinders properly. Do notpuncture an ether cylinder. Keep ether cylindersaway from unauthorized personnel.

Do not spray ether into an engine if the machineis equipped with a thermal starting aid for coldweather starting.

Lines, Tubes and Hoses

Do not bend high pressure lines. Do not strike highpressure lines. Do not install any lines that are bentor damaged.

Repair any lines that are loose or damaged. Leakscan cause fires. Consult your Caterpillar dealer forrepair or for replacement parts.

Check lines, tubes and hoses carefully. Do notuse your bare hand to check for leaks. Use aboard or cardboard to check for leaks. Tighten allconnections to the recommended torque.

Replace the parts if any of the following conditionsare present:

• End fittings are damaged or leaking.

• Outer coverings are chafed or cut.

• Wires are exposed.

• Outer coverings are ballooning.

• Flexible part of the hoses are kinked.

• Outer covers have embedded armoring.

• End fittings are displaced.

Make sure that all clamps, guards, and heat shieldsare installed correctly. During machine operation,this will help to prevent vibration, rubbing againstother parts, and excessive heat.

8/10/2019 KEBU6860-10 S Rodillo


13Safety Section

Fire Extinguisher Location

i00821581

Fire Extinguisher Location

SMCS Code: 7000; 7419

The fire extinguisher should be mounted in alocation on the platform. This is the recommendedlocation. Do not weld the ROPS in order to install thefire extinguisher. Also, do not drill holes in the ROPSin order to mount the fire extinguisher on the ROPS.

If the fire extinguisher is mounted on the ROPS,strap the mounting plate to a leg of the ROPS. Ifthe weight of the fire extinguisher is more than4.5 kg (10 lb), mount the fire extinguisher as lowas possible on one leg. Do not mount the fireextinguisher on the upper one-third area of the leg.

i01557411

Tire Information

SMCS Code: 7000

Explosions of air inflated tires have resulted fromheat-induced gas combustion inside the tires.Explosions can be caused by heat that is generatedby welding, by heating rim components, by externalfire, or by excessive use of brakes.

A tire explosion is much more violent than ablowout. The explosion can propel the tire, the rimcomponents, and the axle components as far as

500 m (1500 ft) or more from the machine. Both theforce of the explosion and the flying debris cancause property damage, personal injury, or death.


(A) At least 15 m (50 ft)(B) At least 500 m (1500 ft)

Do not approach a warm tire. Maintain a minimumdistance, as shown. Stay outside the shaded areain Illustration 15.

Do not use water or calcium as a ballast for thetires. Dry nitrogen gas is recommended for inflationof tires. If the tires were originally inflated with air,nitrogen is still preferred for adjusting the pressure.Nitrogen mixes properly with air.

Nitrogen inflated tires reduce the potential of atire explosion because nitrogen does not aidcombustion. Nitrogen helps to prevent oxidation ofthe rubber, deterioration of rubber, and corrosionof rim components.

To avoid overinflation, proper nitrogen inflationequipment and training in the usage of theequipment are necessary. A tire blowout or a rimfailure can result from improper equipment or frommisused equipment.

When you inflate a tire, stand behind the tread anduse a self-attaching chuck.

Servicing tires and rims can be dangerous. Onlytrained personnel that use proper tools and properprocedures should perform this maintenance. Ifcorrect procedures are not used for servicing tiresand rims, the assemblies could burst with explosiveforce. This explosive force can cause seriouspersonal injury or death. Carefully obey the specificinstructions from your tire dealer.

i01122596

Electrical Storm Injury

PreventionSMCS Code: 7000

When lightning is striking in the vicinity of themachine, the operator should never attempt thefollowing procedures:

• Mount the machine.

• Dismount the machine.

If you are in the operator’s station during anelectrical storm, stay in the operator’s station. If you

are on the ground during an electrical storm, stayaway from the vicinity of the machine.

8/10/2019 KEBU6860-10 S Rodillo


14Safety SectionBefore Starting Engine

i00737899

Before Starting Engine

SMCS Code: 1000; 7000


Make sure that the steering frame lock link isstored in the unlocked position. The steering framelock link must be removed in order to steer themachine. Start the engine only from the operatorcompartment. Never short across the starterterminals or across the batteries. Shorting coulddamage the electrical system by bypassing theengine neutral start system.

Inspect the condition of the seat belt and of themounting hardware. Replace any parts that areworn or damaged. Regardless of appearance,

replace the seat belt after three years of use. Do notuse a seat belt extension on a retractable seat belt.

Adjust the seat so that full pedal travel can beachieved with the operator’s back against the backof the seat.

Make sure that the machine is equipped witha lighting system that is adequate for the jobconditions. Make sure that all machine lights areworking properly. Before you start the engine andbefore you move the machine, make sure thatno one is underneath the machine, around themachine, or on the machine. Make sure that the

area is free of personnel.

i00737922

Engine Starting

SMCS Code: 1000; 7000

If a warning tag is attached to the engine startswitch or to the controls, do not start the engine.Also, do not move any controls.

Move the propel control lever to the center or theNEUTRAL position.

Engage the parking brake.

Diesel engine exhaust contains products ofcombustion which can be harmful to your health.Always run the engine in a well ventilated area. Ifyou are in an enclosed area, vent the exhaust to

the outside.

i01604085

Before Operation

SMCS Code: 7000

Clear all personnel from the machine and from thearea.

Clear all obstacles from the machine’s path. Bewareof hazards (wires, ditches, etc).

Be sure that all windows are clean. Secure thedoors and the windows in the open position or inthe shut position.

Adjust the rearview mirrors for the best visibilityclose to the machine. Make sure that the horn, thebackup alarm (if equipped), and all other warningdevices are working properly.

Fasten the seat belt securely.

i01604109

OperationSMCS Code: 7000

Only operate the machine while you are in a seat.The seat belt must be fastened while you operatethe machine. Only operate the controls while theengine is running.

Check for proper operation of all controls and of allprotective devices while you operate the machineslowly in an open area.

Make sure that no one will be endangered before

you move the machine. Do not allow riders on themachine unless the machine has the followingequipment:

• Additional seat

• Additional seat belt

• Rollover Protective Structure (ROPS)

Report any machine damage that was noted duringmachine operation. Make any necessary repairs.

8/10/2019 KEBU6860-10 S Rodillo


15Safety Section

Parking

Hold attachments approximately 40 cm (15 inches)above ground level while you drive the machine. Donot drive the machine near an overhang, near theedge of a cliff, or near the edge of an excavation.

If the machine begins to sideslip on a grade, turn

the machine downhill.

Be careful to avoid any ground condition whichcould cause the machine to tip. A tip can occurwhen you work on hills or on banks. A tip canoccur when you work on slopes. A tip can alsooccur when you cross ditches, ridges, or otherunexpected obstacles.

When possible, operate the machine up slopes anddown slopes. Avoid operating the machine acrossthe slope, when possible.

Keep the machine under control. Do not overload

the machine beyond capacity.

Make sure that the towing eyes and the towingdevices are adequate for your needs.

Connect trailing equipment only to a drawbar or toa hitch.

There should be no personnel between the machineand the trailing equipment while you maneuver inorder to connect the trailing equipment. Block upthe hitch in order to align the hitch to the drawbar.

Never straddle a wire cable. Never allow other

personnel to straddle a wire cable.

When you maneuver in order to connect theequipment, make sure that no personnel arebetween the machine and trailing equipment. Blockup the hitch of the trailing equipment in order toalign the equipment with the drawbar.

Know the maximum dimensions of your machine.

Always keep the Rollover Protective Structure(ROPS) installed during machine operation.

i01604128

Parking

SMCS Code: 7000

Park on a level surface. If you must park on agrade, chock the machine’s wheels.

Move the propel control lever to the NEUTRALposition. Engage the parking brake.

Lower all attachments to the ground.

Stop the engine.

Turn the engine start switch to the OFF position andremove the engine start switch key.

Turn the battery disconnect switch to the OFF

position. Remove the disconnect switch key if youdo not operate the machine for an extended periodof time. This will prevent drainage of the battery. Abattery short circuit, any current draw from certaincomponents, and vandalism can cause drainageof the battery.

i01329161

Equipment Lowering withEngine Stopped

SMCS Code: 7000

Before lowering any equipment with the enginestopped, clear the area around the equipment ofall personnel. The procedure to use will vary withthe type of equipment to be lowered. Keep in mindmost systems use a high pressure fluid or air toraise or lower equipment. The procedure will causehigh pressure air, hydraulic, or some other media tobe released in order to lower the equipment. Wearappropriate personal protective equipment andfollow the established procedure in the Operationand Maintenance Manual, “Equipment Loweringwith Engine Stopped” in the Operation Section ofthe manual.

i01162688

Sound Information andVibration Information

SMCS Code: 7000

Sound Performance for MachinesOffered in European UnionCountries and in Countries that

Adopt the EU DirectivesThe operator sound pressure level is 75.4 dB(A)measured according to the static test proceduresand conditions specified in “ISO 6394”.

Vibration Level

The hands and arms are exposed to a weighted rootmean square acceleration that is less than 2.5 m/s 2.

The whole body is exposed to a weighted root meansquare acceleration that is less than 0.572 m/s 2.

8/10/2019 KEBU6860-10 S Rodillo


16Safety SectionOperator Station

Measurements are obtained on a representativemachine using the procedures in the followingstandards:

• “ISO 2631/1”

• “ISO 5349”

• “SAE J1166”

i01649970

Operator Station

SMCS Code: 7000; 7300; 7301; 7325

Any modifications to the inside of the operatorstation should not project into the operator space.The addition of a radio, fire extinguisher, and otherequipment must be installed so that the defined

operator space is maintained. Any item that isbrought into the cab should not project into thedefined operator space. A lunch box or other looseitems must be secured. Objects must not pose animpact hazard in rough terrain or in the event of arollover.

KEBU6860-10 S Rodillo

Documents

Transcript of KEBU6860-10 S Rodillo