Cuña Diferencial Lk Rove

La cua de medicin de caudal marca KROVE modelo NICD , incluye un cuerpo bridado y una

restriccin tipo V , esta restriccin desarrolla una presin diferencial , en la cual , la raiz cuadrada

de esta afectada por el factor Kd ( Coeficiente de Caudal ) y Fa ( Factor de Expansion ) da como

resultasdo el caudal Volumtrico.

La conexin de los transmisores de presion son con dos sellos remotos para las conexiones de

presin . De acuerdo a las condiciones del producto , densidad y viscosidad del producto , se

utilizan conexiones bridadas con membrana expuesta

de 11/2 , 3 y 4 .

Este sistema de medicion se recomienda especialmente para la medicin de lquidos viscosos que

contengan slidos en suspensin, los cuales tienden a tapar las tomas de los equipos de medicin

de flujo ms convencionales .

Este sistema de medicion no requiere tramos rectos de entrada y salida por otro lado no posee

superficie crtica bordes abruptos , lo cual no afectar la exactitud de la medicin en el uso normal y

esperado. Por otro lado no existen partes moviles , por lo cual no requiere mantenimiento y

recalibracion .

Esto se ajustar a la relacin entre el ndice de flujo y la presin diferencial sobre el total de los

rangos en nmeros Reynolds de modo tal que los elementos de la cua conducen a si mismos a la

medicin de fluidos viscosos o de fluidos con viscosidad variable.

Cua de Medicin de Caudal

NKCD

Medicin en bajos Numeros de Reynolds(entre 500 y 1.000.000)

Alta Exactitud: +/- 0.5%

Medicin de Flujo Bidireccional.

Baja Prdida de Carga.

Alta Rangueabilidad de hasta 10 a 1.

Excelente prestacin en Emulsiones de Agua + Petroleo.

Especificaciones:

Exactitud : +/- 0.5% del valor leido dentro del rango calibrado.

Repetibilidad : +/- 0.2%.

Elementos Estndar del Puente H/D Ratios

H/D = 0.2 , 0.3 , 0.4 , 0.5.

Para determinar el Ratio H/D y la presin diferencial referir al software de seleccin .

Esto sera funcion de las condiciones de proceso , perdida de carga admisible y rangueabilidad

requerida .

Conexin Bridada a Proceso:

ANSI Class 150 Raised Face.



Perforacin (bore) Interna:

El peso Standard de la caera es el mismo que el

Schedule 40 en 0.5 hasta 10 de tamao, entre tamao

0.375 in y 12 in, hasta 24 in, de tamao de la caera.

Alta Presion , la pared de la caera es la misma que el

Schedule 80 en 0.5 in hasta 8, tamao y 0.5 sobre 10.

hasta 24 , de tamao de la caera.

Materiales de Construccin:

Los materiales Standard son SST316 y acero al carbono,

Hastelloy 276 y Monel.

Contctenos en caso de necesitar otros materiales.

Aclaracin: el acero al carbono no se pinta cuando la temperatura mxima de

proceso es superior a 400 F (204 C).

Sellos remotos especiales para aplicaciones en alta temperatura (240 C).

Pipe Dimensions, Inches (mm) Weight Class, lbs (kg)

Size A B C D E 150 300 600

1-1/2 28.00 (711.20) 14.00 (355.60) 04.63 (117.60) 09.26 (235.20) 06.95 (176.53) 43 (19.50) 49 (22.22) 51 (23.13)

2 28.00 (711.20) 14.00 (355.60) 04.93 (125.22) 09.26 (235.20) 07.19 (182.63) 51 (23.13) 55 (24.95) 59 (26.76)

3 34.00 (863.60) 17.00 (431.80) 07.56 (192.02) 15.12 (384.05) 07.75 (196.85) 69 (31.29) 79 (35.83) 84 (38.10)

4 36.00 (914.40) 18.00 (457.20) 07.50 (190.50) 15.00 (381.00) 08.25 (209.55) 91 (41.27) 109 (49.43) 135 (61.22)

6 40.00 (1016.00) 20.00 (508.00) 09.00 (228.60) 18.00 (457.20) 09.31 (236.47) 115 (52.15) 155 (70.29) 219 (99.32)

8 42.00 (1066.80) 21.00 (533.40) 10.25 (260.35) 20.50 (520.70) 10.31 (261.87) 140 (63.49) 198 (89.79) 294 (133.33)

10 45.00 (1143.00) 22.50 (571.50) 11.75 (298.45) 23.50 (596.90) 11.38 (289.05) 206 (93.42) 286 (129.70) 462 (209.52)

12 47.00 (1193.80) 23.50 (596.90) 13.25 (336.55) 26.50 (673.10) 12.38 (314.45) 280 (126.98) 394 (178.68)

14 49.00 (1244.60) 24.50 (622.30) 14.00 (355.60) 28.00 (711.20) 13.00 (330.20) 347 (157.36) 517 (234.46)

Flanged Wedge Flow Element with Chemical Tee Connection

Pipe Dimensions, Inches (mm) Weight Class, lbs (kg)

Size A B C D E 150 300 600

1/2 18.00 (457.20) 09.00 (228.60) 03.25 (82.55) 06.50 (165.10) 01.00 (25.40) 23 (10.43) 23 (10.43) 23 (10.43)

1 19.00 (482.60) 09.50 (241.30) 03.56 (90.42) 07.12 (180.85) 01.50 (38.10) 26 (11.79) 29 (13.15) 30 (13.64)

1-1/2 20.00 (508.00) 10.00 (254.00) 04.00 (101.60) 08.00 (203.20) 01.86 (47.24) 43 (19.50) 49 (22.22) 51 (23.13)

2 21.00 (533.40) 10.50 (266.70) 04.19 (106.43) 08.38 (212.85) 02.25 (57.15) 51 (23.13) 55 (24.94) 59 (26.76)

3 24.00 (609.60) 12.00 (304.80) 05.19 (131.83) 10.38 (263.65) 02.75 (69.85) 69 (31.29) 79 (35.83) 84 (38.09)

4 30.00 (762.00) 15.00 (381.00) 07.50 (190.50) 15.00 (381.00) 03.06 (77.72) 91 (41.27) 109 (49.43) 135 (61.22)

6 34.00 (863.60) 17.00 (431.80) 09.00 (228.60) 18.00 (457.20) 04.12 (104.65) 115 (52.17) 155 (70.29) 219 (99.32)

8 36.00 (914.40) 18.00 (457.20) 10.25 (260.35) 20.50 (520.70) 05.12 (130.05) 140 (63.49) 198 (89.79) 294 (133.33)

10 40.00 (1016.00) 20.00 (508.00) 11.75 (298.45) 23.50 (596.90) 06.19 (157.23) 206 (93.42) 286 (129.70) 462 (209.52)

12 42.00 (1066.80) 21.00 (533.40) 13.25 (336.55) 26.50 (673.10) 07.19 (182.63) 290 (131.52) 394 (178.68)

14 43.00 (1092.20) 21.50 (546.10) 14.00 (355.60) 28.00 (711.20) 07.81 (198.37) 347 (157.36) 517 (234.46)

Notes:

1. Flange bolt holes are equidistant from center line of pipe.

2. Use preformed gasket and SAE Grade 5 mounting screw provided with chemical tee. Do Not Subsitute.

3. Transmitter flange and flow element have the same rating.

CODIFICACION PARA CAUDALIMETROS CUA DIFERENCIAL

NKCD: CUA DIFERENCIAL CON CONEXIONES DE SELLOS REMOTOS.-

CONEXIONES A PROCESO

F Bridas

X Otras

DIAMETRO NOMINAL DE LA CUA DIFERENCIAL

A DN15

B 1 -DN 25

C 1 1/2 -DN 40

D 2 -DN 50

E 3 -DN 80

F 4 -DN 100

G 6 -DN 150

H 8 -DN 200

I 10 -DN 250

J: 12 -DN 300

K: 14 -DN 350

RELACION H/D EN LA CUA DIFERENCIAL

02 H/D = 0,2

03 H/D = 0,3

04 H/D = 0,4

05 H/D = 0,5

06 H/D = 0,6

99 Otra

MATERIAL CONSTRUCTIVO

CS Acero al carbono.-

SS Acero inoxidable.-

HS Hastelloy C.-

MN Monel.-

OT Otro.-

NIVEL DE DISEO

A Modelo A

BRIDAS DE CONEXIN A PROCESO

A15 Segn normas ANSI # 150



D10 Segn normas DIN PN10

D40 Segn normas DIN PN40

OTR Otras.-

ESPESOR DE PARED DEL TUBO

1 Espesor normal (Sch40)

2 Espesor reforzado (Sch80)

9 Otro.-

CONEXIONES AL TRANSMISOR (SELLOS)

1 Bridas normalizadas tamao 1 .-

2 Bridas normalizadas tamao 3.-

3 Bridas normalizadas tamao 4.-

9 Otros tamaos.-

- GUION de separacin

MAXIMA TEMPERATURA DE PROCESO

1 Hasta 204C

2 Ms de 204C

CALIBRACION EN BANCO DE ENSAYO

A con agua (unidireccional).-

B bidireccional con agua.-

C otras.-

- GUION de separacin

XXXXXX: nmero clave de fabricacin

EJEMPLO: NKCDFD04CSAA1511-1A-070530

SPECIFICATIONS

DATA SHEET FKD...4

REMOTE SEAL TYPEDIFFERENTIAL PRESSURE TRANSMITTER

The FCX A2 differential pressure transmitter accuratelymeasures differential pressure, liquid level or gauge pressureand transmits a proportional 4 to 20mA signal. The trans-mitter utilizes a unique micromachined capacitance siliconsensor with state-of-the-art microprocessor technology toprovide exceptional performance and functionality. Totallywelded construction of the seals assures excellent reliabilityin high temperature and highly corrosive process conditions.

1. High accuracy0.2% accuracy for all calibrated spans is a standardfeature for all DP models covering 0.32kPa{3.2mbar}range to 500kPa{5bar} high differential pressure range.0.1% accuracy is available as option. Fuji's micro-capacitance silicon sensor assures this accuracy for allelevated or suppressed calibration ranges withoutadditional adjustment.

2. Minimum environmental influenceThe "Advanced Floating Cell" design which protects thepressure sensor against changes in temperature, staticpressure, and overpressure substantially reduces totalmeasurement error in actual field applications.

3. Fuji/HART bilingual communications protocol andFOUNDATION fieldbus and Profibus compatibil-ityFCXA2 series transmitter offers bilingual communi-cations to speak both Fuji proprietary protocol andHART. Any HART compatible devices can commu-nicate with FCXA2. Further, by upgrading electron-ics FOUNDATION fieldbus and Profibus are alsoavailable.

4. Application flexibilityVarious options that render the FCX A2 suitable foralmost any process applications include: Analog indicator at either the electronics side or

terminal side Full range of hazardous area approvals Built-in RFI filter and lightning arrester 5-digit LCD meter with engineering unit Stainless steel electronics housing Wide selection of materials High temperature, high vacuum seals

5. Programmable output Linearization FunctionIn addition to Linear and Square Root, output signalcan be freely programmable.(Up to 14 compensated points at approximation.)

6. Burnout current flexibility (Under Scale: 3.2 to 3.8mA,Over Scale: 20.8 to 21.6mA)Burnout signal level is adjustable using Model FXWHand Held Communicator (HHC) to comply withNAMUR NE43.

7. Dry calibration without reference pressureThanks to the best combination of unique constructionof mechanical parts (Sensor unit) and high performanceelectronics circuit (Electronics unit), reliability of drycalibration without reference pressure is at equal levelas wet calibration.

Remark : To minimize environmental influence, span should be greaterthan 1/40 of the max. span in most applications.

Lower limit of static pressure (vacuum limit),Silicone fill sensor: See Fig. 1Fluorinated fill sensor: Atmospheric pressure

The maximum span of each sensor can be convertedto different units using factors as below.

1MPa =103kPa=10bar=10.19716kgf/cm2

=145.0377psi1kPa=10mbar=101.976mmH2O=4.01463H2O

Overrange limit: To maximum static pressure limitOutput signal: 4 to 20mA DC (linear or square root) with

digital signal superimposed on the 4 to20mA signal

Power supply: Transmitter operates on 10.5V to 45V DCat transmitter terminals.10.5V to 32V DC for the units with optionalarrester.

FEATURES

Functional specifications

Service: Liquid, gas, or vapourStatic pressure, span, and range limit:

} Up to flange ratingFKD 3FKD 5FKD 6+/ 32

{+/ 320}+/ 130

{+/ 1300}+/ 500

{+/ 5000}

0.32 { 3.2 }

1.3 { 13 }

5 { 50 }

32{ 320 }

130{ 1300 }

500 { 5000}

Min.Type

Range limit[kPa] {m bar}

Span limit [kPa](m bar}

Max.Static pressure

DateEDSX6-117g

Oct. 15, 2003

FKD...4

2

Loop-check output:Transmitter can be configured to provideconstant signal 3.8mA through 21.6mA byHHC(1).

Temperature limit:Ambient: 40 to + 85C

( 20 to + 80C for LCD indicator)( 40 to + 60C for arrester option)( 10 to + 60C for fluorinated oil fill transmitter)( 10 to + 85C for silicone oil "H", "S", "K")(+ 20 to + 85C for silicone oil "J", "T")For explosionproof units (flameproof or intrinsic safety),ambient temperature must be within the limits speci-fied in each standard.

Process:

Zero/span adjustment:Zero and span are adjustable from theHHC(1). Zero and span are also adjustableexternally from the adjustment screw(span odjustment is not available with 9thdigit code "L, P, M, Q, S, N").

Damping: Adjustable from HHC or local adjustmentunit with LCD display.The time constant is adjustable between0.12 to 32 seconds.

Zero elevation/suppression:100% to +100% of URL

Normal/reverse action:Selectable from HHC(1)

Indication: Analog indicator or 5-digit LCD meter, asspecified.

Burnout direction: Selectable from HHC(1)

If self-diagnostic detect transmitter fail-ure, the analog signal will be driven to ei-ther Output Hold, Output Overscaleor Output Underscale modes.

Output Hold:Output signal is hold as the value just be-fore failure happens.

Output Overscale:Adjustable within the range 20.8mA to21.6mA from HHC(1)

Output Underscale:Adjustable within the range 3.2mA to3.8mA from HHC(1)

3.83.2 4 20 20.8 21.6 [mA]

Over scale Burnout

Probable over rangeProbable under range

Normal operating rangeUnder scale Burnout

Load limitations: see figure below

Note: For communication with HHC(1) (Model: FXW), min. of 250 isrequired.

Hazardous locations:

Lower limitof

static press.

Processtemperature

Atmosphericpressure

Fill fluidCode in the13th digit of

"Code symbols"

20 to 120C

15 to 250C

85 to 300C

40 to 120C

15 to 250C

85 to 300C

15 to 200C

W, A and D

H

J

Y and G

S

T

K

Fluorinated oil

Silicone oil

2.7kPa abs{20mmHgabs}

0.13kPa abs{1mmHg abs}or more

Storage: 40 to +90CHumidity limit: 0 to 100% RHCommunication: With HHC(1) (Model FXW, consult Data

Sheet No. EDS8-47), following informa-tion can be remotely displayed or recon-figured.Note: HHC's version must be more than

6.0 (or FXW 1 3), for FCX-A2.

2000

[]

1500

1000

Load

res

ista

nce

500

250

1533

600Operatingarea

24V 45V

10 16.1 50 [ V ]10.5V

Power voltage

Programmable output linearization function:Output signal can be characterized with14 points linear approximation functionfrom HHC(1).

(Note) (1) HHC: Hand Held Communicator

v v

v v

v

v v

v

v v

v v

v v

v v

v v

v v

v

v

v

v v

v v

v v

v v

Items Display Set

Tag No.

Model No.

Serial No.

Engineering unit

Range limit

Measuring range

Damping

Linear

Square root

Burnout direction

Calibration

Output adjust

Data

Self diagnoses

Printer

External switch lock

Transmitter display

Linearize

Rerange

Output mode

ATEX Ex II 2 GD Ex II 1 GD Ex II 3 GD - EExd IIC T5/T6 - EExia IIC T4/T5 - EExn IIC T4/T5

Factory Class I II III Class I II III Class I II III Mutual Div. 1 Div. 1 Div. 2

Groups B thru. G Groups A thru. F Groups A thru. GCSA Class I II III Class I II III Class I II III

Div. 1 Div. 1 Div. 2Groups C thru. G Groups A thru. G Groups A thru. G

TIIS Ex do IIB+H2 T4 Ex ia II C T4 (*)

(*) Approval pending

Type nNonincendiveAuthorities Flameproof Intrinsic safety

3Dielectric strength:500V AC, 50/60Hz 1 min., between circuitand earth.

Insulation resistance:More than 100M at 500V DC.

Turn-on time: 4 sec.Internal resistance for external field indicator:

12 or less

Physical specifications

Electrical connections:G1/2, 1/2-14 NPT, Pg13.5, or M20 1.5 con-duit, as specified.And 1-conduit or 2-conduit, as specified.

Process connections:JIS, ANSI, or DIN raised face flanges.JIS: 10K80A, 10K100A, 30K80A, or

30K100AANSI: 150LB 3", 150LB 4", 300LB 3", or

300LB 4"DIN: PN40 DN80 or PN16 DN100See OUTLINE DIAGRAM for detailed di-mensions.

Diaphragm extension:0, 50, 100, 150, or 200mm as specified.(See model code. Extended diaphragm isavailable only with 316L stainless steel orHastelloy-C diaphragm)

Process-wetted parts material:Diaphragm: 316L stainless steel, Hastelloy-

C,Monel, Tantalum, Titanium orZirconium

Flange face:316 stainless steel, Hastelloy-C liningMonel lining, or Tantalum lin-ing

Extension: 316 s t a i n l ess s tee l o rHastelloy-C

Non-wetted parts material:Electronics housing: Low copper die-cast

aluminum alloy finished with epoxy/polyurethane double coating (stan-dard), or 316 stainless steel (SCS14 perJIS G5121), as specified.

Capillary: In case of 11th code "D, E, F, L,M, N, P", PVC armored stainless steel.In case of 13th code "Q, R, S, T, V, W,X", stainless steel armored stainlesssteel.

Mounting flange: 304 stainless steel orcarbon steel

Fill fluid: Silicone oil (standard) or fluori-nated oil

Mounting bracket: 304 stainless steelEnvironmental protection:

IEC IP67 and NEMA 6/6PMounting: On 60.5mm (JIS 50A) pipe using mount-

ing bracket, direct wall mountingMass {weight}: Transmitter approximately 15kg without

options.Add; 0.5kg for mounting bracket

0.8kg for indicator option4.5kg for stainless steel housing

option1.5kg per 50mm extension of diaphragm

Performance specifications

Reference conditions, silicone oil fill, 316SS isolating diaphragms,4 to 20mA analog output in linear mode.Accuracy rating: (including linearity, hysteresis, and re-

peatability)(Standard)For spans greater than 1/10 of URL: 0.2% of spanFor spans below 1/10 of URL:

(Option) (Code; 21th digit H,K)For spans greater than 1/10 of URL: 0.1% of spanFor spans below 1/10 of URL:

Stability: 0.2% of upper range limit (URL) for 3years.

Temperature effect (*):Effects per 28C change between the lim-its of 40C and +85C

(Standard) Zero shift: 0.35% of URLTotal effect: 0.5% of URL

(Option) (Code; 21th digit J,K)Zero shift: 0.3% of URLTotal effect: 0.4% of URLNote: * Excluding effect by temperature difference

between the seals.Static pressure effect:

Zero shift; 0.2% of URL for flange ratingpressure

Span shift: 0.2% of calibrated span forflange rating pressure

Overrange effect: Zero shift; 0.1% of URL for flange ratingpressure

Supply voltage effect:Less than 0.005% fo calibrated span per1V

RFI effect: Less than 0.2% of URL for the frequen-cies of 20 to 1000MHz and field strength30 V/m when electronics covers on.(Classification: 2-abc: 0.2% span per

SAMA PMC 33.1)Step response: (without electrical damping)

0.1+0.1 % of span0.1 URL

Span( )

0.05+0.05 % of span0.1 URL

Span( )

Range code

"3"

"5"

"6"

Time constant (*)

2 s

1.7 s

1.7 s

Dead time (*)

0.2 s

*) Faster response is available as option (maximumupdate rate: 25 times per second).

FKD...4

4

Optional features

Indicator: A plug-in analog indicator (1.5% accuracy)can be housed in the electronics compart-ment or in the terminal box of the hous-ing.An optional 5-digit LCD meter with engi-neering unit is also available.

Local adjustment unit with LCD display:An optional 5-digit LCD meter with Zero/Span adjustment function, loop-checkfunction and damping adjustment func-tion, is available.

Arrester: A built-in arrester protects the electronicsfrom lightning surges.Lightning surge immunity:4kV (1.2 50s)

Oxygen service: Special cleaning procedures are followedthroughout the process to maintain all pro-cess wetted parts oil-free.The fill fluid is fluorinated oil.

Chlorine service: Oil-free procedures as above. Includesfluorinated oil for fill.

Degreasing: Process-wetted parts are cleaned, but thefill fluid is standard silicone oil. Not for useon oxygen or chlorine measurement.

Vacuum service: Special silicone oil and filling procedureare applied.See Fig. 1, Fig. 2.

Optional tag plate:An extra stainless steel tag for customertag data is wired to the transmitter.

Coating of cell: Cell's surface is finished with epoxy/poly-urethane double coating. Specify if envi-ronment is extremely corrosive.

ACCESSORIES

Hand-held communicator:(Model FXW, refer to Data Sheet No. EDS8-47)

Z/S board: Parts No.=ZZPFCX4-A070When Z/S board is mounted on the FCXA2 amplifier unit, external adjustmentscrew will be available for zero and spanadjustment.

Fig. 2 Relation between process temperature andoperating pressure

Silicone (Code Y,G)

Silicone (Code S)

Operating area

Silicone (Code T)

101{1010}

53.3 {533}

13.3 {133}

2.7 {27}

[kPa abs]{mbar abs}

Ope

ratin

g p

ress

ure

40 15 60 85 120 200 230 250 300Process temperature[C ]

Sealing liquid:Silicone (Code K)

Operating area

Non-operatingarea

101{1010}

0.27 {2.7}0.13 {1.3}

[kPa abs]{mbar abs}

Ope

ratin

g p

ress

ure

20015 100Process temperature[C ]

Fig. 1 Relation between process temperature andoperating pressure

5CODE SYMBOLS

G 1/2 (1)1/2-14NPT (1)Pg13.5 (1)M20 1.5 (1)G 1/2 (2)1/2-14NPT (2)Pg13.5 (2)M20 1.5 (2)

Mounting flange304 stainless steel

Carbon steel

316 stainless steel

None(wafer type)

0.32.... 32{3.2..... 320}1.3...... 130{13...... 1300}5......... 500{50...... 5000}

Diaphragm316L stainlesssteel

Hastelloy-C

316L stainless+Au coatingMonelTantalumTitaniumZirconium

Description Note

Note 2

Note 3

Note 1

Digit4

5

7

6

4 5 6 71 2 3

F 04K D8 9 10 11 12 13 14 15 21 Digit No.

of code

ABCDSTVW

0123456789MRABCDEFGHJKSTUVWXPQ

3

5

6

VABCDHFGKLJ

MTPR

Flange size and ratingJIS 10K 80AJIS 10K 100AJIS 30K 80AJIS 30K 100AANSI/JPI 150LB 3"ANSI/JPI 150LB 4"ANSI/JPI 300LB 3"ANSI/JPI 300LB 4"DIN PN16/40 DN80DIN PN16 DN100JIS 20K 80AANSI/JPI 600LB 3BJIS 10K 80AJIS 10K 100AJIS 30K 80AJIS 30K 100AANSI/JPI 150LB 3"ANSI/JPI 150LB 4"ANSI/JPI 300LB 3"ANSI/JPI 300LB 4"DIN PN16/40 DN80DIN PN16 DN100JIS 10K 80AANSI/JPI 150LB 3BANSI/JPI 150LB 4BANSI/JPI 300LB 3BANSI/JPI 300LB 4BANSI/JPI 600LB 3B3 inch wafer4 inch wafer

Flange face316 stainlesssteel

Hastelloy-C

316 stainless stell

MonelTantalumTitaniumZirconium

Diaph. extension [mm] 0

50 100 150 200

0 50

100 150 200

0

0 0 00

(*2)

(*3)

Note 1: (*1) 100: 1 turn down is possible, but should be used at a span greater than 1/40 of the maximum span for better performance.

Note 2: (*2) Available for 13th digit code "S", "T", "K" and 5th digit code "1", "3", "5", "7", "B", "D", "F", "H", "K", "Q", "U", "W".

Note 3: (*3) Available for 6th code "2", "3" and 5th code "0", "2", "4", "6", "8", "A", "C", "E", "G", "J", "P", "M", "R", "S", "T", "W".

Combination with 12th digit code "C, E, P, Q" are notavailable.

FKD...4

6

None (for ordinary locations)TIIS, Flameproof (Conduit seal) (Available for 4th digit code "A", "S")TIIS, Flameproof (Cable gland seal) (Available for 4th digit code "A", "S")FM, Flameproof (or explosionproof) (Available for 4th digit code "B", "T")CSA, Flameproof (or explosionproof) (Available for 4th digit code "B", "T")ATEX, FlameproofTIIS, Intrinsic safety (Approval pending)FM, Intrinsic safety and nonincendiveCSA, Intrinsic safety and nonincendiveATEX, Intrinsic safetyATEX, Type n

Capillary Mounting bracket armor of capilary 1.5 m 304 Stainless steel PVC (*4)3 304 Stainless steel PVC (*4)5 304 Stainless steel PVC (*4)6 304 Stainless steel PVC (*4)7 304 Stainless steel PVC (*4)8 304 Stainless steel PVC (*4)10 304 Stainless steel PVC (*4)1.5 304 Stainless steel Stainless steel (*5)3 304 Stainless steel Stainless steel (*5)5 304 Stainless steel Stainless steel (*5)6 304 Stainless steel Stainless steel (*5)7 304 Stainless steel Stainless steel (*4)8 304 Stainless steel Stainless steel (*4)10 304 Stainless steel Stainless steel (*4)

Extra SS tag plate Stainless steel elec. housing Coating of cell None None None Yes None None None Yes None Yes Yes None None None Yes Yes None Yes None Yes Yes Yes Yes Yes

Note 4: (*4) Available for 13th digit code "Y, W, G, A, D". Inquire about in case of 13th other code.Note 5: (*5) Available for all 13th digit code.Note 6: (*6) Customer tag number can be engraved on standard stainless steel

name plate. If extra tag plate is required, select "Yes".

Description Note

Note 4Note 4Note 4Note 4Note 4Note 4Note 4Note 5Note 5Note 5Note 5Note 4Note 4Note 4

Note 6

Digit

10

11

12

4 5 6 71 2 3

F 04K D8 9 10 11 12 13 14 15 21 Digit No.

of code

ABCDEXGHJKP

YBCEMNPQ

DELFMNPQRSTVWX

(*6)

Indicator ArresterNone NoneAnalog, 0 to 100% linear scale NoneAnalog, 0 to 100% sq. root scale NoneAnalog, custom scale NoneAnalog, double scale (linear and sq. root) NoneNone YesAnalog, 0 to 100% linear scale YesAnalog, 0 to 100% sq. root scale YesAnalog, custom scale YesAnalog, double scale (linear and sq. root) YesDigital, 0 to 100% NoneDigital, custom scale NoneDigital, 0 to 100% square root NoneDigital, 0 to 100% YesDigital, custom scale YesDigital, 0 to 100% square root YesDigital, 0 to 100%(Local adjustment unit with LCD display) NoneDigital, custom scale(Local adjustment unit with LCD display) NoneDigital, 0 to 100% square root(Local adjustment unit with LCD display) NoneDigital, 0 to 100%(Local adjustment unit with LCD display) YesDigital, custom scale(Local adjustment unit with LCD display) YesDigital, 0 to 100% square root(Local adjustment unit with LCD display) Yes

9

ABCDJEFGHKLPMQSN1

2

3

4

5

6

Z/S board attached.Approval pendingfor 10th digit code"G, H, J, K, P"

Approval pendingfor 10th digit code"D, E, G, H, J, K, P"

Construccin.

Calibracin en Proveer propio.

Distribucin.

Pgina 1Pgina 2Pgina 3Pgina 4Pgina 5KROVE_cua_diferencial_fuji.pdfSpecificationsOrderingDataFiles

cuadros.pdfPgina 1Pgina 2

codificacion.pdfPgina 1

Cuña Diferencial Lk Rove

Documents

Transcript of Cuña Diferencial Lk Rove