AE-966 / AE-967 manual · Los analizadores de espectros AE-966/967 cubren la banda de frecuencias...
Transcript of AE-966 / AE-967 manual · Los analizadores de espectros AE-966/967 cubren la banda de frecuencias...
AE-966 / AE-967
ANALIZADOR DE ESPECTROS DE 3,0 GHz
3.0 GHz SPECTRUM ANALYSER
- 0 MI1486 -
NOTAS SOBRE SEGURIDAD Antes de manipular el equipo leer el manual de instrucciones y muy especialmente el apartado PRESCRIPCIONES DE SEGURIDAD.
El símbolo sobre el equipo significa "CONSULTAR EL MANUAL DE INSTRUCCIONES". En este manual puede aparecer también como símbolo de advertencia o precaución.
Recuadros de ADVERTENCIAS Y PRECAUCIONES pueden aparecer a lo largo de este manual para evitar riesgos de accidentes a personas o daños al equipo u otras propiedades.
SAFETY NOTES Read the user’s manual before using the equipment, mainly " SAFETY RULES " paragraph.
The symbol on the equipment means "SEE USER’S MANUAL". In this manual may also appear as a Caution or Warning symbol.
Warning and Caution statements may appear in this manual to avoid injury hazard or damage to this product or other property.
SUMARIO CONTENTS
Manual español.............................................................
English manual .............................................................
Eng
lish
MANUAL DE INSTRUCCIONES AE-966 / 967
Í N D I C E
1 GENERALIDADES ................................................................................................... 1
1.1 Descripción ........................................................................................................ 1 1.2 Especificaciones .............................................................................................. 3
2 PRESCRIPCIONES DE SEGURIDAD ................................................................... 7
2.1 Generales .......................................................................................................... 7 2.2 Ejemplos descriptivos de las Categorías de Sobretensión ............................... 8
3 INSTALACIÓN.......................................................................................................... 9
3.1 Alimentación ...................................................................................................... 9 3.2 Ajuste de los pies de soporte............................................................................. 9
4 GUÍA RÁPIDA DE USO.......................................................................................... 11
4.1 Descripción general ......................................................................................... 11 4.2 Guía rápida ...................................................................................................... 11
4.2.1 Frecuencia y Span................................................................................... 11 4.2.2 Amplitud................................................................................................... 12 4.2.3 Autoset..................................................................................................... 12 4.2.4 Marcadores.............................................................................................. 13 4.2.5 Búsqueda de Picos.................................................................................. 13 4.2.6 Trazo........................................................................................................ 14 4.2.7 Medidas de Potencia ............................................................................... 14 4.2.8 Línea Límite ............................................................................................. 15 4.2.9 Ancho de banda....................................................................................... 16 4.2.10 Disparo (Trigger)...................................................................................... 16 4.2.11 Pantalla.................................................................................................... 16 4.2.12 Archivo..................................................................................................... 17 4.2.13 Preset ...................................................................................................... 18 4.2.14 Sistema.................................................................................................... 18 4.2.15 Opciones.................................................................................................. 18 4.2.16 Secuencia ................................................................................................ 19
5 ESTRUCTURA DE LOS MENÚS ........................................................................... 21
5.1 Frecuencia, Span, Autoset, Amplitud (1 de 2). ................................................ 21 5.2 Amplitud (2 de 2), Marcador ............................................................................ 22 5.3 Búsqueda de Picos, Trazo............................................................................... 23 5.4 Medidas, Línea Límite ..................................................................................... 25 5.5 BW, Disparo, Pantalla...................................................................................... 27 5.6 Archivo............................................................................................................. 28 5.7 Sistema............................................................................................................ 29 5.8 Opciones, Secuencia....................................................................................... 30
MANUAL DE INSTRUCCIONES AE-966 / 967
6 INSTRUCCIONES DE MANEJO ............................................................................ 31
6.1 Descripción de mandos y elementos............................................................... 31 6.1.1 Panel frontal............................................................................................. 31 6.1.2 Panel Posterior ........................................................................................ 33
6.3 Funciones principales ...................................................................................... 35 6.3.1 Funciones de frecuencia y span. ............................................................. 35 6.3.2 Amplitud................................................................................................... 42 6.3.3 Autoset..................................................................................................... 53 6.3.4 Marcadores.............................................................................................. 56 6.3.5 Búsqueda de picos .................................................................................. 64 6.3.6 Trazo........................................................................................................ 70 6.3.7 Medidas de potencia................................................................................ 81 6.3.8 Línea de límite ......................................................................................... 90 6.3.9 Ancho de banda....................................................................................... 96 6.3.10 Disparo(trigger) ...................................................................................... 104 6.3.11 Pantalla.................................................................................................. 107 6.3.12 Archivo/Impresión .................................................................................. 113 6.3.13 Función Preset....................................................................................... 123 6.3.14 Sistema (system) ................................................................................... 124 6.3.15 Secuencia (seq)..................................................................................... 135 6.3.16 Generador de Tracking.......................................................................... 141 6.3.17 Demodulador (opcional) ........................................................................ 143 6.3.18 Filtro EMI (opcional)............................................................................... 146 6.3.19 Software de Ordenador ......................................................................... 148 6.3.20 Comunicación Remota .......................................................................... 158
7 SINTAXIS DE LOS COMANDOS ......................................................................... 161
7.1 Comandos ..................................................................................................... 162 8 MANTENIMIENTO................................................................................................ 185
8.1 Funcionamiento con Batería (opcional)/ Corriente Continua......................... 185 8.1.1 Funcionamiento con Batería.................................................................. 185 8.1.2 Funcionamiento con corriente continua................................................. 186
8.2 Sustitución del fusible de red......................................................................... 187 8.3 Recomendaciones de limpieza...................................................................... 188
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 1
ANALIZADOR DE ESPECTROS AE-966 y AE-967
1 GENERALIDADES 1.1 Descripción
Los analizadores de espectros AE-966/967 cubren la banda de frecuencias de 9 KHz a 3 GHz y permiten una operación estable con un span de 2 KHz a 3 GHz.
El AE-966 es el modelo básico, mientras que el AE-967 incorpora un Generador de seguimiento (Tracking Generator) lo que le convierte en un instrumento ideal para la medida de respuesta de filtros, amplificadores, atenuadores, cables y en general cualquier sistema de radiofrecuencia ya sea en cadenas de producción, centros de investigación o verificación de campo gracias a su funcionamiento a baterías (opcional).
Presenta una amplia gama de funciones como los marcadores, trazas, medidas
de potencia, líneas de límite, división de ventanas en pantalla y sincronismo que permiten realizar las medidas de una forma más fácil y rápida. La salida directa VGA es ideal para realizar presentaciones.
El generador de seguimiento que incorpora el AE-966-967 permite obtener
respuestas en frecuencia dentro de la misma banda de trabajo. El interfaz RS-232 y USB hacen posible su interconexión con un PC para que los usuarios puedan desarrollar sus propias aplicaciones. La alimentación a 12 V DC permite al usuario el transporte del equipo durante los desplazamientos con vehículo entre puntos de medida distantes. Los filtros EMI ( Opcional) de 9 kHz y 120 kHz y el detector de cuasi-picos facilitan las pruebas EMC.
Caracteristicas:
- Bajo nivel de ruido:-117 dBm a 600 MHz, 3k RBW.
- Barrido rápido: 50ms ~ 25.6s.
- Generador de Tracking (sólo AE-967).
- Auto-ajuste.
- 5 marcadores con Marcador Delta (relativo) y funciones de Pico.
- 3 trazas.
- Medidas de potencia: ACPR, OCBW, N-dB, Oscilaciones de Fase..
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 2 02/2007
- Test Pasa-No Pasa con edición de la línea del límite.
- Ventanas separadas con ajustes individuales.
- Programación secuencial (macro definido por usuario).
- Pantalla TFT en color de 6.4 ”, con resolución 640 x 480.
- Salida de auriculares (disponible en el Demodulador opcional).
- Funcionamiento con AC / DC / Baterías (Opcional).
- Tamaño compacto: 330 x 170 x 340 mm.
- Peso ligero: 6 kg (sin opciones).
Interfaz
- Entrada USB para conexión de dispositivos de almacenaje y para impresión directa de imágenes de pantalla.
- USB (esclavo)/RS232/GPIB (opcional) para conexión al ordenador.
- Salida directa de la imagen de pantalla VGA para conexión y visualización en monitores externos.
- Entrada/salida de la señal de referencia para sincronización.
- Entrada de señal de disparo externo.
Extras Opcionales
- Filtro EMI con 9kHz/120kHz RBW y 6dB de ancho de banda.
- Pack de baterías.
- Demodulador AM/FM.
- 300Hz/10kHz/100kHz RBW.
- Interfaz GPIB.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 3
1.2 Especificaciones FRECUENCIA Margen De 9 kHz a 3,0 GHz Precisión ver base de tiempos. Precisión Span ver base de tiempos. Escala Span 2 kHz a 3,0 GHz en secuencia 1-2-5, span
completo, span cero Ruido de fase -80 dBc/Hz típico para 1 GHz, Offset 20 KHz. Base de tiempos ±10 ppm, de 0 a 50 °C, 5 ppm/año ANCHO DE BANDA Selección RBW 3 kHz, 30 kHz, 300 kHz, 4 MHz Precisión RBW ± 15% Ancho de banda de vídeo 10 Hz a 1 MHz en pasos 1-3 Tiempo de barrido 50 ms a 25,6 s AMPLITUD Escalas entrada 1 MHz a 15 MHz 15 MHz a 600 MHz 600 MHz a 2,3 GHz 2,3 GHz a 3,0 GHz Escala nivel de referencia -30 dBm a + 20 dBm, protección sobrecarga. Precisión ±1 dB para 100 MHz Planitud frecuencial (Flatness) ±1 dB Linealidad del nivel de amplitud ±1 dB sobre 70 dB Protección sobrecargas +30 dBm, ±25 VDC Promedio del nivel base de ruido -135 dBm/Hz: 1 MHz a 15 MHz -152 ± 1dBm/Hz: 15 MHz a 600 MHz -149 ± 1dBm/Hz: 600 MHz a 2,3 GHz -147 ± 1dBm/Hz: 2,3 GHz a 3,0 GHz Distorsión armónica <-60 dBc para entrada de <—40 dBm Respuesta espúreos no- armónicos <-110 dBm a 3kHz RBW Intermodulación (3er orden) <-70 dBc para entrada de -40 dBm Detección de trazas Promedio (Average), Retención Máximo (Max.
hold), Congelado (freeze), Traza Matemática (Trace Math).
ENTRADA Entrada RF Protección de sobrecarga +30 dBm Continua Impedancia Nominal 50 Ω Pérdidas de retorno <2:1, Nivel ref. 0 dBm Conector Tipo N hembra
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 4 02/2007
Frecuencia entrada reloj ref. ext. 1 MHz, 1,544 MHz, 2,048 MHz, 5 MHz, 10
MHz, 10,24 MHz, 13 MHz, 15,36 MHz, 15,4 MHz, 19,2 MHz
OTRAS FUNCIONES Memoria interna 10 Trazos, 10 Información de sistema, 10
Líneas de límite, 5 Correcciones, 10 Secuencias.
Medida de Potencia ACPR, OCBW, potencia canal, N dB BW y Oscilación de fase.
Salida Reloj de Referencia 10 MHz CONECTORES Puerto RS-232 Para el volcado de la pantalla a un PC
(software gratuito). Entrada de disparo externo BNC, señal TTL +5V. Conector USB Panel delantero: Tipo A. Panel trasero: Tipo B mini. Salida de Voltaje de DC Macho SMB, salida máxima de +9V/100mA. GENERADOR DE SEGUIMIENTO o TRACKING (sólo AE-967) Margen de frecuencia 9 kHz a 3,0 GHz Amplitud -50 dBm a 0 dBm Precisión de amplitud ±1 dB (0 dBm, 100 MHz) Planitud de amplitud ±1 dB (0 dBm). Armónicos <-30 dBc típico. Máxima potencia de retorno +30 dBm Impedancia de entrada Nominal 50 Ω Pérdidas de retorno < 2:1 INTERFAZ GPIB (opcional) FILTRO EMI (opcional) Filtro RBW de 9 kHz a 120 kHz Precisión 15 % DEMODULADOR AM/FM Y RBW DE 10kHz Y DE 100kHz (opcional). Demodulador AM, FM. Salida Altavoz Interno, conector estéreo de 3,5 mm
preprado para funcionamiento en modo mono. Selección de RBW 10 kHz y 100 kHz, ancho de banda de 3dB. Precisión de RBW 15 %.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 5
GENERAL Pantalla Pantalla TFT-LCD en color de alta resolución
640 x 480. Marcadores 10 marcadores para picos: 5 pares de
marcadores normal-delta. Funciones: Delta, Pico, Rastreo de marcador.
Función Autoset El autoset ajusta las medidas en la pantalla. Secuencia Prueba automatizada, basada en macros
definidos por el usuario.
ALIMENTACIÓN Tensión de red 100 a 240 V AC, 50-60 Hz. Consumo 90 W Interna Batería (opcional) Pack de baterías Li-Ion con cargador integrado. Externa DC 12 V Consumo 40 W
CONDICIONES AMBIENTALES DE UTILIZACIÓN Uso en interiores Altitud Hasta 2000 m Temper. óptima de utilización De 18 a 28 °C Humedad Relativa De 0 a 90 %
CONDICIONES AMBIENTALES DE ALMACENAMIENTO Margen de temperaturas De 0 a 40 °C Humedad relativa < 85% CARACTERÍSTICAS MECÁNICAS Dimensiones 330 A x 170 Al x 340 Pr. mm Peso 6 kg sin opciones
ACCESORIOS INCLUIDOS Cable de red CA-05 CD — Software 0 DK0742 Adaptadores N-BNC 2x AD059
OPCIONES Interfaz GPIB OP-966-A Pack de baterias OP-966-CU (2 x baterías Li-Ión modelo 202S). Filtro de resolución 300Hz RBW OP-966-E (*) Filtro de resolución 9KHz y 120KHz RBW OP-966-D (*) Demodulación AM/FM y filtros de 10kHz y 100kHz RBW OP-966-M (*) Adap. Alimentación Automóvil AA-12
(*) Solo una de estas opciones puede estar instalada. Instalación en fabrica al hacer el pedido del equipo. No se puede realizar la instalación posteriormente.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 6 02/2007
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 7
2 PRESCRIPCIONES DE SEGURIDAD
2.1 Generales
* La seguridad puede verse comprometida si no se aplican las instrucciones dadas en este Manual.
* Utilizar el equipo solamente en sistemas o aparatos con el negativo de medida conectado al potencial de tierra.
* Este es un equipo de clase I, por razones de seguridad debe conectarse a líneas de suministro con la correspondiente toma de tierra.
* Este equipo puede ser utilizado en instalaciones con Categoría de Sobretensión II y ambientes con Grado de Polución 2 (Ver 2.2).
* Al emplear cualquiera de los siguientes accesorios debe hacerse sólo con los tipos especificados a fin de preservar la seguridad.
Cable de red Batería (opcional)
* Tener siempre en cuenta los márgenes especificados tanto para la alimentación como para la medida.
* Recuerde que las tensiones superiores a 70 V DC o 33 V AC rms son potencialmente peligrosas.
* Observar en todo momento las condiciones ambientales máximas especificadas para el aparato.
* El operador sólo está autorizado a intervenir en:
Sustitución del fusible de red, que deberá ser del tipo y valor indicados. Cambio de batería.
En el apartado de Mantenimiento se dan instrucciones específicas para estas intervenciones.
Cualquier otro cambio en el equipo deberá ser efectuado exclusivamente por personal especializado.
* El negativo de medida se halla al potencial de tierra.
* No obstruir el sistema de ventilación del equipo.
* Utilizar para las entradas/salidas de señal, especialmente al manejar niveles altos, cables apropiados de bajo nivel de radiación.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 8 02/2007
* Seguir estrictamente las recomendaciones de limpieza que se describen en el apartado Mantenimiento.
* Símbolos relacionados con la seguridad:
CORRIENTE CONTINUA
CORRIENTE ALTERNA
TERMINAL A CARCASA
MARCHA
PARO
DOBLE AISLAMIENTO
(Protección CLASE II)
PRECAUCIÓN
(Riesgo de choque eléctrico)
PRECAUCIÓN VER MANUAL
FUSIBLE
TERMINAL DE TIERRA
TERMINAL DE PROTECCIÓN
2.2 Ejemplos descriptivos de las Categorías de Sobretensión
Cat I Instalaciones de baja tensión separadas de la red Cat II Instalaciones domésticas móviles Cat III Instalaciones domésticas fijas Cat IV Instalaciones industriales
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 9
3 INSTALACIÓN
3.1 Alimentación
Los analizadores de espectros AE-966 y AE-967 están preparados para ser alimentados con tensiones de red de 100 a 240V AC 50-60 Hz ± 10 %. También permiten ser alimentados a 12 V DC o baterías recargables utilizando el cargador integrado.
3.2 Ajuste de los pies de soporte
Los analizadores de espectros AE-866 y AE-867 poseen cuatro pies de soporte así como un asa de transporte. Los pies permiten orientar el analizador de espectros bajo un ángulo de visualización óptimo, para ello se deben seguir los siguientes pasos:
Pies con extremidad
Pies sin extremidad
Empujar haciaadelante la extremidad
Tirar hacia atrás de laextremidad
Girar la extremidad hasta el finalpara un mayor ángulo de elevación
Girar la extremidad hasta el finalpara un menor ángulo de elevación
Figura 1.- Pies de soporte del analizador de espectros
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 10 02/2007
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 11
4 GUÍA RÁPIDA DE USO
4.1 Descripción general
Este capítulo contiene todas las secuencias de teclas para las distintas operaciones que se pueden realizar con el equipo; los contenidos de los menús de pantalla; y los ajustes de fábrica, que se pueden recuperar con la tecla Preset. Use este capítulo como una referencia rápida cuando necesite acceso rápido a la operación que desea realizar, y cuando necesite una vista general de las funciones del equipo.
4.2 Guía rápida
4.2.1 Frecuencia y Span
Teclas función Descripción
Frequency → F1 Span → F1
Ajustar la Frecuencia Central y el Span.
Frequency → F2, F3 Ajustar de Frecuencia de Inicio y de Final.
Frequency → F4 Ajustar el Paso de la Frecuencia
Span → F2 Activar Span Completo (3.0GHz)
Span → F3 Activar Span Cero (Dominio Temporal)
Span → F4 Recuperar el Último Span
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 12 02/2007
4.2.2 Amplitud
Teclas función Descripción
Amplitude → F1 Ajustar Nivel de Referencia.
Amplitude → F2 Seleccionar Escala Vertical.
Amplitude → F3 →F1∼F3 Seleccionar Unidad (dBm/dBmV/dBuV)
Amplitude → F4 Ajustar Compensación Externa.
Amplitude →F5→F2 Activar Corrección de Amplitud.
Amplitude →F5→F1→F1 Seleccionar Ajustes de Corrección de Amplitud
Amplitude →F5→F1→F2 Eliminar un Elemento de Corrección de Amplitud
Amplitude →F5→F1→F3→F2 Eliminar un Ajustes de Corrección de Amplitud
Amplitude →F5→F1→F4 Deshacer Corrección de Elemento o Eliminación de Ajustes
Amplitude →F5→F1→F5 Guardar Ajustes de Corrección de Amplitud
Amplitude →F6→F1 Seleccione la Impedancia de Entrada (50 Ω /75 Ω)
Amplitude →F6→F2 Ajustar Compensación de Impedancia de Entrada
4.2.3 Autoset
Teclas función Descripción
Autoset → F1 Ejecutar Autoset.
Autoset → F2 Ajustar Nivel Mínimo de Amplitud
Autoset → F3 Ajustar Span de Visualización de Frecuencia
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 13
4.2.4 Marcadores
Teclas función Descripción
Marker → F1, F2 Activar Marcador Normal
Marker →F1, F2, F3 Activar Marcador Delta (relativo)
Marker →F6→F3 Activar Todos los Marcadores Normales
Marker →F4 o Peak Search→F1 Mover Marcador a Pico
Marker →F4,F5 o Peak Search→F5 Centrar Marcador y Pico
Peak Search→F6→F4 Rastrear Marcador a Pico
Marker →F6→F4→F1∼F5 Mover Marcador a Varias Posiciones
Marker →F6→F2 Mostrar Tabla de Marcadores
Marker →F6→F1 Fijar Marcador a Trazo
4.2.5 Búsqueda de Picos
Teclas función Descripción Peak Search→F1 o Marker→F4 Buscar Señal de Pico.
Peak Search→F2, F3 (derecha), F4 (izquierda) Buscar Siguiente Pico.
Peak Search→F5 o Marker→F4, F5 Buscar y Centrar Pico.
Peak Search→F6→F4 Rastrear Marcador en Pico.
Peak Search→F6→F5 Buscar Amplitud Mínima.
Peak Search→F6→F1 Mostrar Tabla de Picos.
Peak Search→F6→F2 Organizar Picos en Tabla de Picos.
Peak Search→F6→F3 Ajustar Umbral de Pico.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 14 02/2007
4.2.6 Trazo
Teclas función Descripción
Trace→F1 Activar Trazo
Trace→F2 Actualizar Trazo en Tiempo real (Por defecto)
Trace→F3 Visualizar Trazo de Pico Fijado
Trace→F4 Congelar Trazo
Trace→F5 Ocultar Trazo
Trace→F6→F1 o BW→F4 Visualizar Trazo Promedio
Trace→F6→F2→F1~F5 Ejecutar Matemáticas de Trazo
Trace→F6→F3→F1~F5 Seleccionar Modo de Detección de Señal
4.2.7 Medidas de Potencia
Teclas función Descripción
Meas→F2 Activar ACPR
Meas→F1→F1 Ajustar Ancho de Banda del Canal ACPR Principal
Meas→F1→F2 Ajustar Espacio del Canal ACPR
Meas→F1→F4→F2, F4 Ajustar Compensación del Canal Adyacente
Meas→F1→F4→F1, F3 Ajustar Ancho de banda del Canal Adyacente
Meas→F4 Mover el Canal ACPR hacia Arriba
Meas→F5 Mover el Canal ACPR hacia Abajo
Meas→F3 Activar OCBW
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 15
Teclas función Descripción
Meas→F1→F1 Ajustar Ancho de banda del Canal OCBW
Meas→F1→F2 Ajustar Espacio del Canal OCBW
Meas→F1→F3 Ajustar % de OCBW
Meas→F4 Mover el Canal OCBW hacia Arriba
Meas→F5 Mover el Canal OCBW hacia Abajo
Meas→F6→F1 Activar N dB
Meas→F6→F2 Ajustar el Valor de N dB
Meas→F6→F3 Activar Oscilaciones de Fase
Meas→F6→F4→F1 (Inicio), F2 (Final) Ajustar Compensación de Oscilaciones de Fase
4.2.8 Línea Límite
Teclas función Descripción Limit Line→F1 (Alto), F2 (Bajo) Activar Línea Límite
Limit Line→F3→F1 Seleccionar Línea Límite para Editar
Limit Line→F3→F2 Activar la Tabla de Edición de la Línea Límite
Limit Line→F3→F3 (Eliminar) Eliminar un Elemento de la Tabla de la Línea Límite
Limit Line→F3→F4→F1, F2 Eliminar Todos los Elementos de la Tabla
Limit Line→F3→F5 Deshacer la Última Eliminación
Limit Line→F4 Ejecutar Test Pasa-No Pasa
Limit Line→F5 Seleccionar Condición Pasa-No Pasa
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 16 02/2007
4.2.9 Ancho de banda
Teclas función Descripción
BW→F1 Seleccionar RBW
BW→F2 Seleccionar VBW
BW→F3 Ajustar Tiempo de Barrido
BW→F4 o Trace→F6→F1 Ajustar Número Promedio Trazo
BW→F5 Reiniciar RBW/VBW/Barrido a Auto
4.2.10 Disparo (Trigger)
Teclas función Descripción
Trigger→F1 Seleccionar Disparo Automático (Predeterminado)
Trigger→F2 Seleccionar Disparo de Vídeo/Externo
Trigger→F3 Seleccionar Modo de Disparo
Trigger→F4 Ajustar Retraso de Disparo
Trigger→F5 Ajustar Frecuencia de Disparo
Trigger→F6 Ejecutar Disparo (Único/Continuo)
4.2.11 Pantalla
Teclas función Descripción
Display→F1 Cambiar Nivel de Brillo
Display→F2 Mostrar Línea de Pantalla
Display→F3→F1 Eliminar Título
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 17
Teclas función Descripción
Display→F3→F2~F4 Introducir Título
Display→F3→F5 Mostrar Título
Display→F4→F1 (Superior), F2 (Inferior)
Activar División de Pantalla
Display→F4→F3 Alternar Barrido Superior/Inferior
Display→F4→F4 Cambiar Pantalla Dividida a Pantalla Completa
4.2.12 Archivo
Teclas función Descripción
File→F1→F1→F1~F5 Seleccionar Archivo a Copiar
File→F1→F2→F1~F5 Seleccionar Destino de Copia
File→F1→F3 Editar Nombre de Archivo Copiado
File→F1→F4 Copiar Archivo Seleccionado
File→F2→F1→F1~F5 Seleccionar Archivo para Eliminar
File→F2→F2 Eliminar Archivo Seleccionado
File→F3→F1 Renombrar Archivo
File→F3→F2 Confirmar Nuevo Nombre de Archivo
File→F4→F1 Imprimir Imagen de Pantalla
File→F4→F2→F2 Guardar Imagen de Pantalla a Dispositivo USB
File→F4→F2→F1 Renombrar Archivo en Dispositivo USB
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 18 02/2007
4.2.13 Preset
Teclas función Descripción
Preset Recuperar Ajustes Predeterminados
4.2.14 Sistema
Teclas función Descripción System→F1→F1~F2 (Seleccionar), F3 (Guardar)
Guardar Ajustes
System→F1→F1~F2 (Seleccionar), F4 (Recuperar)
Recuperar Ajustes
System→2 Ajustar Dirección de GPIB
System→F3→F1~F4 Mostrar Configuración RS-232C
System→F4 Activar Señal Auxiliar
System→F6→F1→F1→F1~F4 Ajustar Fecha
System→F6→F1→F2→F1~F3 Ajustar Hora
System→F6→F1→F3 Activar Reloj de Pantalla
System→F6→F2→F1~F4 Visualizar Resultados de Auto-test
System→F6→F4 Visualizar Configuración del Sistema
System→F6→F5→F1 Seleccionar Idioma
4.2.15 Opciones
Teclas función Descripción
Option→F1→F1 Activar Generador de Seguimiento (TG)
Option→F1→F2 Ajustar Amplitud del Generador de Seguimiento
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 19
Teclas función Descripción Option→F1→F3→F1 (No), F2 (Sí)
Normalizar Generador de Seguimiento (TG)
Option→F1→F4 Activar normalizado del Generador de Seguimiento.
Option→F1→F5 Ajustar Nivel de Referencia para Normalización de TG
Option→F2→F1 Activar Demodulador FM
Option→F2→F2 Activar Demodulador AM
Option→F2→F3 Activar Salida audio (conector auriculares)
Option→F2→F4 Ajustar Volumen de Salida de Audio.
Option→F2→F5 Ajustar Nivel de Ruido
Option→F3 Visualizar Nivel de Batería
Option→F4 Ajustar Frecuencia de Señal de Referencia Externa
4.2.16 Secuencia
Teclas función Descripción
Sequence→F1, F2 Seleccionar Ajustes de Secuencia
Sequence→F3→F1 Iniciar Edición de Secuencia
Sequence→F3→F2 Introducir Retraso de 100ms
Sequence→F3→F3 Introducir Pausa en la Secuencia
Sequence→F3→F4→F1~F2 Introducir Otro Ajuste de Secuencia
Sequence→F3→F5 Detener Edición de Secuencia
Sequence→F3→F6→F1 Introducir Elemento en los Ajustes de Secuencia
Sequence→F3→F6→F2 Guardar Ajustes de Secuencia
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 20 02/2007
Teclas función Descripción
Sequence→F3→F6→F3 Eliminar Elemento de Secuencia
Sequence→F3→F6→F4→F1, F2
Eliminar Ajustes de Secuencia
Sequence→F3→F6→F5 Deshacer Eliminación de Ajustes o Elementos de Secuencia
Sequence→F4→F1 Seleccionar Modo de Ejecución de Secuencia
Sequence→F4→F2 Ejecutar Secuencia
Sequence→F5→F1 (No), F2 (Sí)
Suprimir Todos los Ajustes de Secuencia
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 21
5 ESTRUCTURA DE LOS MENÚS
La estructura de los menús de opciones proporciona una visión general de la estructura del interfaz de usuario. Este capítulo 5 ofrece las explicaciones más detalladas de cada tecla de función.
5.1 Frecuencia, Span, Autoset, Amplitud (1 de 2).
Center1.5 GHz F 1
Start0 kHz F 2
Stop3 GHz F 3
Step0 kHz F 4
Frequency
Span3 GHz F 1
Full Span F 2
Zero Span F 3
Last Span F 4
Span
SpanAuto Man F 3
Autoset F 1
Autoset
Amp.FloorAuto Man F 2
Ref.Level-30.0dBm F 1
Scale dB/Div10 5 2 1 F 2
Units... F 3
Ext.Gain0dB F 4
Corrections.. F 5
More F 6
dBm F 1
dBmV F 2
dBuV F 3
Return F 6
Amplitude
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 22 02/2007
5.2 Amplitud (2 de 2), Marcador
Scale dB/Div10 5 2 1 F 2
Units... F 3
Corrections.. F 5
More F 6
InputZ50Ω 75Ω
F 1
Input Z Cal5.9dB F 2
Return F 6
Select1 2 3 4 5 F 1
Delete F 2
Delete All.. F 3
Undelete F 4
Return F 6
Edit... F 1
CorrectionOn Off F 2
Return F 6
No F 1
Yes F 2
Return F 6
Ref.Level-30.0dBm F 1
Ext.Gain0dB F 4
Amplitude
Save Now F 5
Marker1 2 3 4 5 F 1
On Off F 2
To Peak F 4
Mkr Center F 5
More F 6
Marker TraceAuto A B C F 1
Mkr to... F 4
Return F 6
Mkr Center F 1
Mkr Start F 2
Mkr Stop F 3
Mkr CFStep F 4
Return F 6
Mkr Ref Lvl F 5
Marker
ModeNormal ∆Mkr F 3
Marker TableOn Off F 2
All MkrsOn Off F 3
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 23
5.3 Búsqueda de Picos, Trazo
Pk Search F 1
Next Peak F 2
Next PkRight F 3
Next Pk Left F 4
More F 6
Peak TableOn Off F 1
Pk ThresholdOn Off F 3
TrackOn Off F 4
Return F 6
Mkr Center F 5 Min Search F 5
Peak Search
Peak SortFreq Amp F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 24 02/2007
Clear F 2
Peak Hold F 3
View F 4
Blank F 5
More F 6
AVGOn Off
20F 1
Trace Math.. F 2
Detection.. F 3
Return F 6
Normal F 1
Sample F 2
Peak+ F 3
AVG F 4
Return F 6
A B F 1
A+B A F 2
Return F 6
QPeak F 5
A-B A F 3
A+const A F 4
Trace
TraceA B C F 1
A-const A F 5
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 25
5.4 Medidas, Línea Límite
CH Up F 4
CH Down F 5
More F 6
ChannelSetup... F 1
N dB F 2
CH BW F 1
CH SPC F 2
OCBW % F 3
ADJ CHOffset... F 4
Return F 6
Adj CH BW1 F 1
Adj CH Offs1 F 2
Return F 6
Adj CH BW2 F 3
Adj CH Offs2 F 4
Phase JitterOn Off F 3
Phase JitterSetup F 4
Return F 6
StartOffset F 1
StopOffset F 2
Return F 6
Meas
ACPROn Off F 2
OCBWOn Off F 3
N dB BWOn Off F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 26 02/2007
Edit... F 3
Edit TableOn Off F 2
Delete F 3
Return F 6
No F 1
Yes F 2
Return F 6
Delete All.. F 4
Undelete F 5
Limit Line
H LimitOn Off F 1
L LimitOn Off F 2
Pass/FailOn Off F 4
Pass/Fail___ F 5
LimitLow High F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 27
5.5 BW, Disparo, Pantalla
RBWAuto Manu F 1
VBWAuto Manu F 2
All Auto F 5
BW
Swp TmAuto Manu F 3
AVGOn Off 20 F 4
Free Run F 1
Trigger ModeNorm. Sgl. Cont. F 3
Trigger Freq1.5GHz F 5
Trigger
TriggerCondition
Video Ext.F 2
Trigger Delay50ms F 4
Run Now F 6
LCD Dimmer F 1
(Capital Letter) F 2
Title... F 3
Split Window... F 4
Return F 6
Clear Title F 1
Show Title F 5
Upper F 1
Lower F 2
Return F 6
(Small Letter) F 3
(Symbol) F 4
AlternateSweep F 3
Full Screen F 4
Display
Display LineOn Off F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 28 02/2007
5.6 Archivo
Copy... F 1
Source.. F 1
Destination.. F 2
Return F 6
Delete... F 2
Rename... F 3
Print Screen.. F 4
Return F 6
Edit File Name F 3
Copy Now F 4
Return F 6
Type... F 1
Delete Now F 2
Return F 6
Edit File Name F 1
Return F 6
To Printer F 1
Return F 6
Edit File Name F 1
Print Now F 2To Ext.Memory... F 2
File Type
FileType
FileType
FileType
File
TraceInt. Ext. F 1
LimitInt. Ext. F 2
CorrectionInt. Ext. F 3
Seq.Int. Ext. F 4
SetupInt. Ext. F 5
Confirm F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 29
5.7 Sistema
Serial Port.. F 3
Service... F 5
RF Diagno... F 3
Return F 6
SystemClock... F 1
Self Test... F 2
Return F 6
Date... F 1
Time... F 2
(English) F 1
Return F 6 Return F 6
GPIBPass Fail F 1
FlashPass Fail F 2
Year F 1
Month F 2
Day F 3
Return F 6
Hour F 1
Minute F 2
Second F 3
Return F 6
Language F 5
System ConfigOn Off F 4
GPIB Add8 F 2
More... F 6
ClockOn Off F 3
SDRAMPass Fail F 3
RTCPass Fail F 4
Return F 6
Setup6 7 8 9 10 F 2
Save/RecallSetup.. F 1
Save Now F 3
Recall Now F 4
Stop1 F 3
Return F 6
Baud115200 F 1
ParityNone F 2
Data8 F 4
*
System
*
Setup1 2 3 4 5 F 1
Day of Week F 4
Aux SigOn Off F 4
* Submenú sólo para personal de mantenimiento
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 30 02/2007
5.8 Opciones, Secuencia
TG... F 1
Demod... F 2
Battery F 3
TGOn Off F 1
TG Level F 2
ExecuteNormalization..
F 3
Ref Value F 5
Return F 6
FMOn Off F 1
AMOn Off F 2
Volume F 4
Squelch F 5
Return F 6
Option
No F 1
Yes F 2
Return F 6
Norm CorrOn Off F 4
SPKOn Off F 3
Ext Ref Freq10MHz F 4
Start Edit F 1
Delay ms100 X F 2
Wait to go F 3
Do Seq... F 4
Seq.Index6 7 8 9 10 F 2
Return F 6
Stop Edit F 5
More F 6
No F 1
Yes F 2
Return F 6
Insert F 1
Save F 2
Undelete F 5
Return F 6
Select Seq6 7 8 9 10 F 2
Edit... F 3
Run... F 4
DeleteSeq All... F 5
Delete F 3
Delete All.. F 4
Run Now F 2
Return F 6
No F 1
Yes F 2
Return F 6
Seq
Select Seq1 2 3 4 5 F 1 Seq.Index
1 2 3 4 5 F 1
Run ModeRept. Sngl. F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 31
6 INSTRUCCIONES DE MANEJO
6.1 DESCRIPCIÓN DE MANDOS Y ELEMENTOS 6.1.1 Panel frontal
F 1
F 2
F 3
F 4
F 5
F 6
Frequency
Span
Amplitude
Autoset
BW
1 2 3 4 5 6 7 8
910111214 13 Figura 2.- Panel frontal.
[1] Monitor Monitor LCD Color de 640 x 480 de resolución. [2] F1-F6. Teclas que vinculan otras teclas de función del
panel. [3] Funciones principales. Incluyen las funciones más usuales: Frecuencia, Span,
Amplitud y Autoset.. [4] Teclas de medidas. Grupos de medidas que incluyen: Marcador,
Búsqueda de picos, Trazas, Medida de Potencia y Línea límite.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 32 02/2007
[5] Teclas de control. Grupos de funciones de control que incluyen
BW, Disparo, Pantalla y Guardar/Recuperar, el BW presenta RBW, VBW y Tiempo de barrido.
[6] Teclas de estado . Grupos de funciones de estado que incluyen
Preset, Sistema, Opciones y Secuencias. La función Opciones define el estado de todas las opciones.
[7] Tecla ON/STBY. La tecla de ON/STBY selecciona el estado de
funcionamiento del equipo: apagado en modo “Espera” (indicador rojo encendido), encendido (indicador verde encendido). Para activar/desactivar la alimentación general del equipo, utilice el interruptor situado en el panel posterior.
[8] Cursores. Teclas direccionales para seleccionar y
modificar parámetros. [9] Mando rotativo. Permite modificar la opción seleccionada
mediante incrementos finos. [10] Entrada RF. Conector tipo N para entrada de medidas RF. [11] Alimentación del Preamplificador Terminal de alimentación para preamplificador. [12] Teclas de edición. Incluye número, unidades, signo menos, retroceso
y tecla de entrada. [13] TG Output. Conector tipo N para la salida sincronizada del
TG. [14] Salida USB Conector macho USB, tipo A, guarda/recupera
datos e imprime la imagen de la pantalla
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 33
6.1.2 Panel Posterior
RS-232
PHONE
GPIB
VGA
FREQADJUST
REF INPUT
10 MhzREF OUTPUT
EXT TRIG.INPUT
DC 12V INPUT
40 W MAX.
15 16 17 18 19 20 21 22
232425262728
Figura 3.- Panel posterior.
[15] FREC. ADJUST. Ajuste de la frecuencia de referencia interna, la cual permite alinear la frecuencia con otros equipos.
[16] GBIP Terminal GPIB (opcional). [17] Conector USB Miniconector de tipo B para conexión al
ordenador. [18] RS232 Terminal RS232. [19] Headphone Salida de auriculares para la demodulación
AM/FM (opcional). [20] Compartimento Pack Baterías Compartimento para instalar el pack de baterías
(opcional). Girar el tornillo de la tapa en sentido antihorario para retirarla. La instalación se realiza fácilmente sustituyendo las baterías del interior y colocando de nuevo la tapa del compartimento.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 34 02/2007
[21] Interruptor de Red Interruptor de alimentación a la red eléctrica. [22] Portafusible Contiene fusible de red. [23] Entrada AC Entrada alimentación de red. [24] DC Input Entrada 12 V DC. [25] Salida VGA Conector VGA hembra de 15 pins. Muestra en
un monitor externo una imagen de resolución 640 x 480.
[26] Trigger Input Entrada de disparo externo. Ver
Trigger>>función External [27] 10 MHz Ref Output Salida de 10 MHz que permite la sincronización
con otros equipos [28] REF INPUT Entrada de la señal de referencia externa.
Cuando este terminal es alimentado con una señal de referencia externa, la frecuencia del sistema se sincroniza con ella. Ver opción >> función ExtRefFreq.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 35
6.3 Funciones principales
6.3.1 Funciones de Frecuencia y Span.
La tecla Frequency, junto con la tecla Span, ajusta la escala de frecuencia. Existen dos métodos disponibles. El método Centro-Span define el punto de central y el rango de frecuencia circundante. El método Inicio-Final define el principio y el final del rango de frecuencia. Los ajustes especiales de Span están disponibles para Span Completo/Cero. También se puede recuperar el último ajuste de Span.
6.3.1.1 Visualización de Señal (Centro-Span).
El método Centro-Span define la frecuencia central y el ancho de banda izquierda/derecha (Span) para localizar la señal.
• Definir el paso de ajuste de frecuencia.
Información general
El paso de ajuste de frecuencia define la resolución de las teclas Direccionales para la frecuencia de Centro, Inicio y Final.
1.- Pulse la tecla Frecuency.
Frequency
2.- Pulse F4 (Step). Step0 kHz F 4
Pasos a realizar
3.- Introduzca el valor utilizando las teclas numéricas, las teclas Direccionales y el Selector rotativo.
µ
Rango 0.0kHz ~ 3.0GHz * Resolución de las teclas Direccionales y el Selector rotativo: 1/10 del Span.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 36 02/2007
• Ajustar Frecuencia Central.
1.- Pulse la tecla Frecuency. Frequency
2.- Pulse F1 (Center). Center
1.5 GHz F 1
Pasos a realizar
3.- Introduzca el valor utilizando las teclas numéricas, las teclas Direccionales y el Selector rotativo.
µ
Rango 0,0kHz ~ 3,0GHz * Resolución de las teclas Direccionales y el Selector rotativo: Valor del paso.
Nota La Frecuencia Central y el Span cambian automáticamente según los ajustes de frecuencia de Inicio/Final, y viceversa.
Pantalla
• Ajustar el Span de Frecuencia
1.- Pulse la tecla Span. Span
2.- Pulse F1 (Span). Span
3 GHz F 1
Pasos a realizar
3.- Introduzca el valor utilizando las teclas numéricas, las teclas Direccionales y el Selector rotativo.
µ
Rango 2 kHz ~ 3 GHz * Resolución de las teclas Direccionales y el Selector rotativo: Secuencia 1-2-5 (0 [Cero Span], 2 kHz, 5 kHz, 10 kHz, 20 kHz, 50 kHz..... 1GHz, 2GHz, 3GHz)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 37
Nota La Frecuencia Central y el Span cambian automáticamente según los
ajustes de frecuencia de Inicio/Final, y viceversa. Pantalla
6.3.1.2 VisualizarSeñal (Inicio-Final)
El método Inicio-Final define el Inicio y el Final del rango de frecuencia. • Definir el paso de ajuste de frecuencia. Información general
El paso de ajuste de frecuencia define la resolución de las teclas Direccionales para la frecuencia de Centro, Inicio y Final.
1.- Pulse la tecla Frecuency.
Frequency
2.- Pulse F4 (Step). Step0 kHz F 4
Pasos a realizar
3.- Introduzca el valor utilizando las teclas numéricas, las teclas Direccionales y el Selector rotativo.
µ
Rango 0.0kHz ~ 3.0GHz * Resolución de las teclas Direccionales y el Selector rotativo: 1/10 del Span.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 38 02/2007
• Ajustar Frecuencia Inicial.
1.- Pulse la tecla Frecuency. Frequency
2.- Pulse F2 (Start). Start
0 kHz F 2
Pasos a realizar
3.- Introduzca el valor utilizando las teclas numéricas, las teclas Direccionales y el Selector rotativo.
µ
Rango 0,0kHz ~ 3,0GHz (Frecuencia Inicial ≤ Frecuencia Final) * Resolución de las teclas Direccionales y el Selector rotativo: Valor del paso.
Nota La Frecuencia Central y el Span cambian automáticamente según los ajustes de frecuencia de Inicio/Final, y viceversa
Pantalla
• Ajustar Frecuencia Final
1.- Pulse la tecla Frecuency. Frequency
2.- Pulse F3 (Stop). Stop
3 GHz F 3
Pasos a realizar
3.- Introduzca el valor utilizando las teclas numéricas, las teclas Direccionales y el Selector rotativo.
µ
Rango 0,0kHz ~ 3,0GHz (Frecuencia Inicial ≤ Frecuencia Final) * Resolución de las teclas Direccionales y el Selector rotativo: Valor del paso. * Resolución del Selector rotativo: 1/500 del Span
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 39
Nota La Frecuencia Central y el Span cambian automáticamente según los
ajustes de frecuencia de Inicio/Final, y viceversa Pantalla
6.3.1.3 Span Completo/Cero
El Span Completo/Cero ajusta el Span a valores extremos: 3.0GHz (completo) o 0kHz (cero). Estos valores proporcionan modos más rápidos para visualizar señales en algunas situaciones como dominio temporal (Span Cero) para visualizar la modulación, o Span Completo para visualizar señales de frecuencia desconocida. • Visualizar Span de Frecuencia Completa (3.0GHz)
1.- Pulse la tecla Span. Span
Pasos a realizar
2.- Pulse F2 (Full Span). Full Span F 2
Rango 3,0 GHz (Fijo).
Span Completo también ajusta los siguientes parámetros a valores fijos.
- Frecuencia Central: 1.5GHz - Frecuencia Inicial: 0.0kHz - Frecuencia Final: 3.0GHz
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 40 02/2007
Rango 3,0 GHz (Fijo).
Span Completo también ajusta los siguientes parámetros a valores
fijos.
- Frecuencia Central: 1.5GHz - Frecuencia Inicial: 0.0kHz - Frecuencia Final: 3.0GHz
Pantalla
• Visualizar Span de Frecuencia Completa (3,0GHz)
1.- Pulse la tecla Span. Span
Pasos a realizar
2.- Pulse F3 (Zero Span). Zero Span F 3
Rango Frecuencia central (Fija).
El Span Cero también ajusta los siguientes parámetros a valores fijos:
- Frecuencia Inicial: igual que la frecuencia Central. - Frecuencia Final: que la frecuencia Central
Nota Asegúrese que el ajuste de RBW es lo suficientemente grande al usar
el Span Cero para visualizar la modulación de amplitud.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 41
Pantalla Este diagrama muestra un ejemplo de la modulación de amplitud de
la señal de entrada.
• Recuperar el Último Ajuste de Span
1.- Pulse la tecla Span. Span
2.- Pulse F4 (Last Span).
Last Span F 4
Pasos a realizar
3.- El ajuste de Span vuelve a su estado anterior. Niveles recuperables
1 nivel
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 42 02/2007
6.3.2 AMPLITUD
La tecla Amplitude ajusta la escala vertical de la pantalla, incluyendo el límite superior (Nivel de Referencia), Rango/Unidad vertical (Escala de Amplitud y Unidad), y compensación por ganancia o pérdida externas (Compensación Externa). La Corrección de Amplitud ajusta la distorsión de respuesta de la frecuencia causada por redes externas. También se puede ajustar el nivel de impedancia de entrada según las necesidades de la aplicación.
6.3.2.1 Ajustar Escala Vertical.
La escala vertical de la pantalla es definida por el nivel de amplitud de referencia, Rango de amplitud vertical, Unidad de medida y Ajuste de ganancia/pérdida externas. • Ajustar el Nivel de Amplitud de Referencia
El nivel de referencia define el nivel de pantalla más alto.
1.- Pulse la tecla Amplitude. Amplitude
2.- Pulse F2 (Start). Ref.Level
-30.0dBm F 1
Pasos a realizar
3.- Introduzca el valor utilizando las teclas numéricas, las teclas Direccionales y el Selector rotativo.
µ
Rango dBm -110 ~ +20 dBm, resolución de 0.1dB
dBmV -63.01 ~ +66.99 dBmV, resolución de 0.01dB.
dBµV -3.01 ~ +126.99 dBuV, resolución de 0.01dB
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 43
Pantalla
• Seleccionar Escala de Amplitud
1.- Pulse la tecla Amplitude. Amplitude
Pasos a realizar
2.- Pulse F2 (Scale dB/Div) repetidamente para seleccionar la escala.
Scale dB/Div10 5 2 1 F 2
Rango 10, 5, 2, 1 dB/Div
Pantalla
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 44 02/2007
• Seleccionar Unidad de Amplitud
1.- Pulse la tecla Amplitude. Amplitude
2.- Pulse F3 (Units).
Units... F 3
3.-Seleccione la unidad deseada entre: F1 (dBm), F2 (dBmV) y F3 (dBuV). dBm F 1
dBmV F 2
dBuV F 3
Pasos a realizar
4.- Pulse F6 (Return) para volver al menú anterior. Return F 6
Rango dBm -110 ~ +20 dBm
dBmV -63.01 ~ +26.99 dBmV
dBµV -3.01 ~ +126.99 dBµV • Ajustar Nivel de Compensación Externo
La compensación externa compensa la ganancia o pérdida de amplitud causada por un dispositivo o red externa.
1.- Pulse la tecla Amplitude. Amplitude
2.- Pulse F4 (Ext.Gain). Ext.Gain
0dB F 4
Pasos a realizar
3.- Introduzca el valor utilizando las teclas numéricas.
µ
Rango -20.0dB ~ +20.0dB, resolución de 0.1dB
Icono
El icono de amplitud aparece en la parte inferior de
la pantalla cuando el nivel de compensación externo
cambia.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 45
Ejemplo 1.-Antes (Compensación: 0dB)
2.-Después (Compensación: -3dB)
6.3.2.2 Corrección de Amplitud
La corrección de amplitud ajusta la respuesta de frecuencia del equipo cambiando la amplitud para frecuencias específicas.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 46 02/2007
Árbol de menú
Corrections.. F 5
Select1 2 3 4 5 F 1
Delete F 2
Delete All.. F 3
Undelete F 4
Return F 6
Edit... F 1
CorrectionOn Off F 2
Return F 6
No F 1
Yes F 2
Return F 6
Amplitude
Save Now F 5
Correcciones
disponibles
5 grupos, con 30 puntos de correcciones por grupo
Amplitud -40 ~ +40dB por punto de corrección, resolución de 0.1dB
Rango
Frecuencia 9 kHz ~ 3.0GHz, resolución de 1 kHz
Icono
El icono de Amplitud aparece en la parte inferior de la pantalla
cuando la corrección de amplitud está activada.
• Corregir la amplitud, paso a paso Descripción del ejemplo
En este ejemplo, la red entre el equipo y el Dispositivo Bajo Test (DBT)
distorsiona la forma de onda y baja el nivel a alrededor de 2.4GHz. La
corrección de amplitud puede fijar el nivel.
En este ejemplo la amplitud de alrededor de 2.4GHz se incrementa por
+1 ~ +3dB.
Nivel de corrección
2.2GHz +2.5dB
2.3GHz +1.3dB
2.4GHz +2.8dB
2.5GHz +2.5dB
2.6GHz +1.2dB
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 47
Diagrama
Forma de onda (antes de la corrección)
1.- Pulse la tecla Amplitude. Amplitude
2.- Pulse F5 (Corrections). Corrections.. F 5
1. Entrar en modo Edición de Correcciones
3.- Pulse F1 (Edit). La pantalla muestra los
ajustes de corrección. Edit... F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 48 02/2007
1. Entrar en modo Edición de Correcciones
Pulse F1 (Select) repetidamente para
seleccionar Ajustes de Correcciones. Hay
disponibles 5 grupos, con 30 puntos de
correcciones por grupo.
Select1 2 3 4 5 F 1
2. Seleccionar Ajustes de Correcciones
Ejemplo: Ajuste de Correcciones 3
seleccionado
Select1 2 3 4 5 F 1
1.- Asegúrese de que el cursor señala el
primer punto de frecuencia vacío.
Pt. Freq. (MHz) Gain12345
2.- Si es necesario, mueva el cursor
usando las teclas Direccionales
Arriba/Abajo. 3.- Introduzca la frecuencia en MHz
utilizando las teclas numéricas.
9.0 kHz ~ 3.0GHz.
µ
3a. Añadir Punto de Corrección
4.- El cursor se traslada automáticamente
a la casilla Gain (Ganancia). Introduzca la
ganancia en dB utilizando las teclas
numéricas.
-40dB ~ +40dB.
Pt. Freq. (MHz) Gain12345
2200
µ
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 49
5.- Repite el procedimiento anterior para cualquier corrección de
datos. Los puntos se clasifican automáticamente según la frecuencia
(baja → alta).
3b. Modificar
Punto de
Corrección
1. Mueva el cursor utilizando las
teclas Direccionales. 2. Introduzca la nueva
frecuencia o ganancia
utilizando las teclas
numéricas.
Pt. Freq. (MHz) Gain12345
23002.5
240025002600
22001.32.81.81.2
µ
1. Mueva el cursor al objetivo
utilizando las teclas
Direccionales. 2. Pulse F2 (Delete). La
frecuencia y la ganancia se
eliminan a la vez.
Delete F 2
3. Para deshacer la última
eliminación, pulse F4
(Undelete).
Undelete F 4
3c. Eliminar
Punto de
Corrección
Ejemplo: Eliminación del punto 3 Pt. Freq. (MHz) Gain
12345
23002.5
240025002600
22001.32.81.81.2
Pt. Freq. (MHz) Gain12345
23002.5
25002600
22001.31.81.2
1. Pulse F5 (Save Now). Los
datos editados se guardan
internamente.
Save Now F 5
4. Guardar
Ajustes de
Correcciones
2. Pulse F6 (Return) para volver
al menú anterior. Return F 6
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 50 02/2007
5. Activar
Corrección
1. Pulse F2 (Correction ON) para
activar la corrección.
CorrectionOn Off F 2
2. El icono de amplitud aparece
en la zona inferior de la
pantalla.
Después de
la corrección
La respuesta de frecuencia se vuelve lineal (original), y la ganancia se
compensa en +2 ~ +3dB.
• Eliminar todos los datos de Ajustes de Corrección
1.- Pulse la tecla Amplitude. Amplitude
2.- Pulse F5 (Corrections).
Corrections.. F 5
3.- Pulse F1 (Edit). La pantalla muestra los Ajustes de corrección. Edit... F 1
4.- Pulse F1 (Select) repetidamente para
seleccionar el grupo de correcciones. Select
1 2 3 4 5 F 1
Pasos a realizar
5.- Pulse F3 (Delete All). Delete All.. F 3
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 51
6.- Seleccione F1 (No) o F2 (Yes) para
confirmar. Todos los datos en el grupo de correcciones especificado son suprimidos.
No F 1
Yes F 2
7. Pulse F6 (Return) repetidamente para volver al menú anterior.
Return F 6
• Recuperar Ajustes de Corrección Guardados
1.- Pulse la tecla Amplitude. Amplitude
2.- Pulse F5 (Corrections).
Corrections.. F 5
3.- Pulse F1 (Edit). La pantalla muestra los Ajustes de corrección. Edit... F 1
4.- Pulse F1 (Select) repetidamente para
seleccionar el grupo de correcciones. Select
1 2 3 4 5 F 1
5.- Pulse F6 (Return) repetidamente para volver al menú anterior. Return F 6
Pasos a realizar
6.- Pulse F2 (Correction ON) para activar la corrección.
CorrectionOn Off F 2
• Guardar / Copiar / Eliminar / Renombrar archivos de
corrección Información general
Los archivos de corrección pueden ser guardados, copiados, eliminados o renombrados utilizando las funciones de archivo. Pulse la tecla File para acceder a cada función.
File
Guardar /Copiar
Pulse F1 (Copy). Copy... F 1
Eliminar Pulse F2 (Delete).
Delete... F 2
Renombrar Pulse F3 (Rename). Rename... F 3
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 52 02/2007
6.3.2.3 Ajustar Impedancia de Entrada • Seleccionar la impedancia de entrada (50 Ω / 75 Ω) Información general
En la mayoría de casos, la resistencia de entrada más adecuada es de 50 Ω (predeterminada). Use 75 Ω sólo cuando se requiera expresamente, como en señales de Televisión por cable.
1.- Pulse la tecla Amplitude. Amplitude
2.- Pulse F6 (More).
More F 6
3.- Pulse F1 (InputZ 50 Ω / 75 Ω) para seleccionar la impedancia.
InputZ50Ω 75Ω F 1
Pasos a realizar
4.- Cuando se selecciona 75 Ω, el icono de amplitud aparece en la parte inferior de la pantalla.
• Ajustar la compensación de impedancia (sólo 75 Ω) Información general
La transformación de impedancia a 75 Ω también está disponible a través de dispositivos externos como el módulo conversor de impedancia). En estos casos se inducirá una pérdida externa. La compensación de impedancia puede compensar este efecto.
1.- Pulse la tecla Amplitude. Amplitude
2.- Pulse F6 (More).
More F 6
3.- Asegúrese de seleccionar 75 Ω con la tecla F1 (Input Z)..
InputZ50Ω 75Ω F 1
4.- Pulse la tecla F2 (Input Z Cal). Input Z Cal
5.9dB F 2
Pasos a realizar
5.- Introduzca la compensación utilizando las teclas numéricas.
µ
Rango - 10dB ~ + 10dB, resolución de 0,1dB
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 53
6.3.3 AUTOSET
La función de Autoajuste verifica la configuración de la señal de entrada y ajusta automáticamente las escalas horizontal y vertical más adecuadas. El nivel mínimo de amplitud para limitar el rango de búsqueda, y el span de observación de frecuencia para limitar el rango de visualización son customizables según las necesidades de la aplicación.
6.3.3.1 Ejecutar Autoset (buscar el rango de amplitud completa)
1.- Pulse la tecla Autoset. Autoset
Pasos a realizar
2.- Pulse F1 (Autoset). Autoset F 1
Rango de búsqueda
Amplitud dBm -80 ~ +20 dBm
dBmV -33.01 ~ + 66.99 dBmV
dBµV +26.99 ~ + 126.99 dBµV
Frecuencia 0kHz ~ 3.0GHz
* Estos rangos son aplicables cuando tanto el Nivel mínimo de Amplitud
(F2) como el límite de Span (F3) están ajustados a Auto. Ejemplo: antes de Autoajuste
Frecuencia inicial: 0kHz Frecuencia final: 3GHz
Span: 3GHz Pico de señal: 100MHz
Frecuencia central: 1.5GHz Nivel de referencia: -10dBm
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 54 02/2007
Frecuencia inicial: 97.5MHz Frecuencia final: 102.5MHz
Span: 5MHz Pico de señal: 100MHz
Frecuencia central: 100MHz Nivel de referencia: -30dBm
Ejemplo:
después de
Autoajuste
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 55
6.3.3.2 Ajustes RBW / VBW / Barrido después de Autoajuste
Los parámetros RBW, VBW y Barrido se pondrán en modo Automático
después de usar el Autoajuste, sin tener en cuenta sus ajustes anteriores.
• Limitar el rango de búsqueda de la escala vertical Información general
Se puede ajustar el nivel mínimo de amplitud, de modo que las señales más bajas que las ajustadas sean ignoradas por la búsqueda de Autoajuste.
1.- Pulse la tecla Autoset. Autoset
2.- Pulse F2 (Amp.Floor) para cambiar el
rango de Auto (rango total) a manual (rango limitado).
Amp.FloorAuto Man F 2
Pasos a realizar
3.- Introduzca la amplitud en dB, usando las teclas numéricas. La ventana de comandos muestra el ajuste.
µ
Amp. : -30dBm
Rango dBm -80 ~ +20dBm, resolución de 0.1dB
dBmV -33.01 ~ +66.99dBmV, resolución de 0.01dB
dBµV +26.99 ~ +126.99dBµV, resolución de 0.01dB
• Limitar el rango de visualización de la escala horizontal Información general
Se puede cambiar el límite de Span de frecuencia en la pantalla para conseguir una mejor visualización del resultado del Autoajuste. Por defecto, el Span de frecuencia se ajusta a 5MHz (Auto) después del Autoajuste. 1.- Pulse la tecla Autoset.
Autoset
2.- Pulse F3 (Span) para cambiar el rango de Auto (límite fijado en 5MHz) a Manual.
SpanAuto Man F 3
Pasos a realizar
3.- Introduzca la Frecuencia usando las teclas numéricas. La ventana de comandos muestra el ajuste.
µ
Span : 10MHz
Rango Span cero, 2 kHz ~ 3GHz (Manual) Fijado a 5MHz (Auto)
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 56 02/2007
6.3.4 MARCADORES
Un Marcador muestra la frecuencia y la amplitud de un punto de la forma de onda. El equipo puede activar hasta 5 Marcadores o pares de Marcadores simultáneamente. La Tabla de Marcadores ayuda a editar y visualizar múltiples Marcadores en la misma pantalla. También se pueden habilitar/deshabilitar todos los Marcadores a la vez. El Marcador Delta o Relativo (indicado con el símbolo ∆)muestra la diferencia de frecuencia y amplitud con respecto al Marcador de referencia. El equipo puede mover automáticamente el Marcador a varias posiciones, como señal de pico, frecuencia central y frecuencia inicial / final. Hay más operaciones de Marcadores relacionadas con los picos de señal disponibles en la función Búsqueda de Pico.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 57
6.3.4.1 Activar / Desactivar Marcadores Árbol de menú
Las funciones de las teclas F3 ~ F5 están disponibles sólo cuando el Marcador está activado (ON).
More F 6
Marker1 2 3 4 5 F 1
On Off F 2
ModeNormal ∆Mkr F 3
To Peak F 4
Mkr Center F 5
All MkrsOn Off F 3
Marker
Rango Marcador normal: 5
Marcador Delta: 5 pares
Amplitud: -120 ~ +20dBm, resolución de 0.1dB
-73.01 ~ + 66.99dBmV, resolución de 0.01dB
-13.01 ~ + 126.99dBuV, resolución de 0.01dB
Frecuencia: 0kHz ~ 3,0GHz
• Activar Marcadores normales
1.- Pulse la tecla Marker. Marker
2.- Pulse F1 (Marker) repetidamente para
seleccionar un Marcador de 1 a 5. Marker
1 2 3 4 5 F 1
3.- Pulse F2 (ON) para activar el Marcador seleccionado. On Off F 2
4.- Asegúrese de seleccionar Normal en F3.
Si es necesario, pulse y seleccione Normal.
ModeNormal ∆Mkr F 3
Pasos a realizar
5.- Repita los pasos anteriores para el número de marcadores requeridos.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 58 02/2007
Pantalla La esquina superior derecha de la pantalla muestra el Marcador activo.
Número de Marcador , Frecuencia , Amplitud
• Activar 5 marcadores normales a la vez
1.- Pulse la tecla Marker. Marker
2.- Pulse F6 (More)
More F 6
3.- Pulse F3 (All Mkrs On) para activar los 5 marcadores normales.
All MkrsOn Off F 3
Pasos a realizar
4.- Para visualizar el estado de todos los marcadores, pulse F2 (Marker Table On). La frecuencia y la amplitud de los marcadores aparecen en la lista de marcadores.
ModeNormal ∆Mkr F
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 59
Pantalla La esquina superior derecha de la pantalla muestra el estado del marcador activo.
• Activar Marcadores Relativos (Delta)
1.- Pulse la tecla Marker. Marker
2.- Pulse F1 (Marker) repetidamente para
seleccionar un Marcador de 1 a 5. Marker
1 2 3 4 5 F 1
3.- Pulse F2 (ON) para activar el Marcador seleccionado. On Off F 2
4.- Asegúrese de seleccionar ∆ (delta) en F3.
Si es necesario, pulse y seleccione ∆ Mkr. Mode
Normal ∆MkrF 3
Pasos a realizar
5.- Repita los pasos anteriores para el número de marcadores requerido.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 60 02/2007
Pantalla La esquina superior derecha de la pantalla muestra el par de Marcadores delta activo.
6.3.4.2 Mover marcadores
Esta sección da por supuesto que al menos un marcador está activado . Las posiciones de frecuencia de los marcadores se pueden ajustar manualmente, o se pueden colocar en posiciones específicas usando los accesos directos del menú.
• Mover manualmente un marcador
1.- Compruebe el Marcador activo en la esquina superior derecha de la pantalla.
Pasos a realizar
2.- Mueva el Marcador usando las teclas Izquierda/Derecha y Selector rotativo, o introduzca la frecuencia directamente utilizando las teclas numéricas.
µ
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 61
• Mover un marcador al pico más alto
1.- Compruebe el Marcador activo en la esquina superior derecha de la pantalla.
2.- Pulse la tecla Marker. Marker
Método 1
3.- Pulse F4 (To Peak). To Peak F 4
1.- Otro método (con el mismo efecto) es
pulsar la tecla Peak Search. Peak Search Método 2
2.- Pulse F1 (Pk Search). Pk Search F 1
1.- Este método lleva el marcador al pico y
también lo rastrea. Pulse la tecla Peak Search.
Peak Search 2.- Pulse F6 (More).
More F 6
3.- Pulse F4 y active el Track (On). TrackOn Off F 4
Método 3
4.- El icono de rastreo de picos aparece en la parte inferior de la pantalla.
• Mover un marcador y el pico más alto al centro
1.- Compruebe el Marcador activo en la esquina superior derecha de la pantalla.
2.- Pulse la tecla Marker. Marker
3.- Pulse F4 (To Peak). El Marcador se
desplaza al pico de la señal. To Peak F 4
Método 1
4.- Pulse F5 (Mkr→Center). El pico de la señal se desplaza al centro. Mkr Center F 5
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 62 02/2007
1.- Otro método (con el mismo efecto) es
pulsar la tecla Peak Search. Peak Search Método 2
2.- Pulse F5 (Mkr→Center) para localizar el pico de la señal y moverlo al centro. Mkr Center F 5
• Mover un marcador a varias posiciones
1.- Compruebe el Marcador activo en la esquina superior derecha de la pantalla.
2.- Pulse la tecla Marker. Marker
3.- Pulse F6 (More).
More F 6
4.- Pulse F4 (Mkr to ...) Mkr to... F 4
5.- Seleccione el destino y Pulse F1 (Center) ~
F5 (Ref Lvl). Center: frecuencia central Start: frecuencia inicial Stop: frecuencia final CF Step: ajusta la frecuencia del marcador
sumándole el valor de paso de frecuencia Ref Lvl: nivel de amplitud de referencia
Mkr Center F 1
Mkr Start F 2
Mkr Stop F 3
Mkr CFStep F 4
Mkr Ref Lvl F 5
Pasos a realizar
6.- Pulse F6 (Return) para volver al menú anterior. Return F 6
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 63
• Mover un marcador a un trazo
1.- Compruebe el Marcador activo en la esquina superior derecha de la pantalla.
2.- Pulse la tecla Marker. Marker
3.- Pulse F6 (More).
More F 6
Pasos a realizar
4.- Pulse F1 (Marker Trace). Marker TraceAuto A B C F 1
Rango Auto El Marcador se desplaza a la señal/trazo activo.
Trazo A El Marcador se desplaza a Trazo A.
Trazo B El Marcador se desplaza a Trazo B.
Trazo C El Marcador se desplaza a Trazo C. 6.3.4.3 Mostrar Marcadores en Tabla
1.- Compruebe el Marcador activo en la esquina superior derecha de la pantalla.
2.- Pulse la tecla Marker. Marker
3.- Pulse F6 (More).
More F 6
4.- Pulse F2 (Marker Table On). Marker TableOn Off F 2
Pasos a realizar
5.- La tabla de los números de Marcador, la frecuencia y amplitud
aparece en la mitad inferior de la pantalla, actualizada en tiempo real. Pantalla
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 64 02/2007
6.3.5 BÚSQUEDA DE PICOS
La Búsqueda de Picos (Peak Search) encuentra automáticamente los picos de señal en varias condiciones, como siguiente pico máximo y siguiente pico mínimo. La búsqueda de picos se solapa parcialmente con las características de la función Marcador, y es mejor usar las dos funciones juntas. Todos los picos pueden ser visualizados a la vez en la tabla de picos, con umbral de amplitud y ordenación configurables.
6.3.5.1 Buscar Picos de Señal
La función Búsqueda de Picos (Peak Search) pone un Marcador sobre el pico de señal deseado. Si no hay ningún marcador activado, el equipo activa automáticamente el marcador 1. La frecuencia y la amplitud de señal de pico aparecen en la esquina superior derecha de la pantalla.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 65
• Buscar Pico de Señal
1.- Pulse la tecla Peak Search Peak Search
Método 1
2.- Pulse F1 (Pk Search). Pk Search F 1
1.- Otro método consiste en utilizar la tecla Marker. Asegúrese que los
marcadores ya están activados 2.- Pulse la tecla Marker.
Marker
Método 2
3.- Pulse F4 (To Peak). To Peak F 4
1.- Método consiste en un rastreo continuo de
la señal de pico. Pulse la tecla Peak Search. Peak Search 2.- Pulse F6 (More). More F 6
3.- Pulse F4 (Track On). TrackOn Off F 4
Método 3 (Marcador rastreado hasta el pico)
4.- El icono de rastreo de picos aparece en la
parte inferior de la pantalla.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 66 02/2007
• Buscar el siguiente pico más alto
El marcador sigue desplazándose hasta el siguiente pico más alto, en orden descendiente.
1.- Pulse la tecla Peak Search. Peak Search
Pasos a realizar
2.- Pulse F2 ~ F4 repetidamente. Next Peak: mueve el Marcador al siguiente
pico más alto. Next Pk Right: mueve el Marcador al siguiente
pico más alto a la derecha (frecuencia más alta).
Next Pk Left: mueve el Marcador al siguiente pico más alto a la izquierda (frecuencia más baja)
Next Peak F 2
Next PkRight F 3
Next Pk Left F 4
Pantalla
• Buscar el pico más alto y moverlo al centro
1.- Pulse la tecla Peak Search Peak Search
Método 1
2.- Pulse F1 (Pk Search). Pk Search F 1
Método 2 1.- Otro método consiste en utilizar la tecla Marker. Asegúrese que los
marcadores ya están activados
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 67
2.- Pulse la tecla Marker.
Marker
3.- Pulse F4 (To Peak). To Peak F 4
Método 2
4.- Pulse F5 (Mkr→Center). Mkr Center F 5
• Buscar la amplitud mínima
1.- Pulse la tecla Peak Search. Peak Search
2.- Pulse F6 (More). More F 6
Pasos a realizar
3.- Pulse F5 (Min Search). El marcador activo
se desplaza al nivel más bajo del trazo. Min Search F 5
Pantalla
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 68 02/2007
6.3.5.2 Mostrar Tabla de Picos
• Activar la Tabla de Picos
1.- Pulse la tecla Peak Search. Peak Search
2.- Pulse F6 (More). More F 6
Pasos a realizar
3.- Pulse F1 (Peak Table On). Peak TableOn Off F 1
Pantalla
Rango Máximo 10 picos
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 69
• Ajustar umbral de picos
Sólo los picos que se encuentran por debajo del umbral de amplitud se
mostrarán en esta lista.
1.- Pulse la tecla Peak Search. Peak Search
2.- Pulse F6 (More). More F 6
3.- Pulse F1 (Peak Table On). Peak Table
On Off F 1
4.- Pulse F3 (Peak Threshold On). Pk ThresholdOn Off F 3
5.- Una línea horizontal aparece en la pantalla. El equipo busca y
presenta una lista de picos que están debajo del umbral de amplitud.
Pasos a realizar
6.- Use las Teclas direccionales o el Selector
rotativo para mover la línea del umbral.
6.3.5.3 Ordenar picos
Los picos se clasifican por orden de frecuencia ascendente/ amplitud descendente.
1.- Pulse la tecla Peak Search. Peak Search
2.- Pulse F6 (More). More F 6
Pasos a realizar
3.- Pulse F2 (Peak Sort) para cambiar entre
clasificación por amplitud y por frecuencia.
Peak SortFreq Amp F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 70 02/2007
Ejemplo: clasificación por amplitud
6.3.6 TRAZO
El trazo rastrea las variantes de forma de onda. Tres trazos, A, B, y C, están disponibles para acumular el nivel de pico, congelando la forma de onda actual, y promediándola. Las operaciones matemáticas de trazo están disponibles usando los trazos A y B.
Los modos de detección configuran el modo en que el equipo muestrea la señal analógica de entrada para su posterior digitalización.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 71
6.3.6.1 Visualizar forma de onda trazada • Seleccionar (activar) trazo
1.- Pulse la tecla Trace.
Trace Pasos a realizar
2.- Pulse F1 (Trace) repetidamente para seleccionar el trazo.
TraceA B C F 1
Rango A (verde) Trazo predeterminado que está siempre activado.
Junto con el trazo B, ejecuta operaciones matemáticas
de trazo
B (ámbar) Junto con el trazo A, ejecuta operaciones matemáticas
de trazo.
C (amarillo)
• Visualizar trazo actualizado en tiempo real (predeterminado) Información general
El trazo se actualiza en cada barrido. El trazo antiguo se elimina y un
nuevo trazo de acuerdo con los datos de la última medida aparece en
pantalla. 1.- Pulse la tecla Trace.
Trace Pasos a realizar
2.- Pulse F2 (Clear). Clear F 2
Rango El siguiente icono aparecerá en la parte
inferior de la pantalla:
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 72 02/2007
• Visualizar trazo de pico congelado Información general
En el modo congelación de picos, la amplitud del nuevo trazo se
compara con la anterior en cada barrido. Sólo la amplitud más alta
sustituye puntos de trazo anteriores, y así congela el valor de pico más
alto. 1.- Pulse la tecla Trace.
Trace Pasos a realizar
2.- Pulse F3 (Peak Hold). Peak Hold F 3
El siguiente icono aparecerá en la parte
inferior de la pantalla: Rango
El siguiente icono aparecerá en la parte inferior de la pantalla:
Pantalla
Eliminar (Predeterminado)
• Congelar trazo
1.- Pulse la tecla Trace. Trace
2.- Pulse F4 (View). View F 4
Pasos a realizar
3.- El siguiente icono aparecerá en la parte inferior de la pantalla:
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 73
• Ocultar Trazo
1.- Pulse la tecla Trace. Trace
2.- Pulse F5 (Blank). Blank F 5
Pasos a realizar
3.- El trazo desaparece de la pantalla. Para recuperarlo pulse F2 (Clear). Clear F 2
• Visualizar trazo promediado
1.- Pulse la tecla Trace. Trace
2.- Pulse F6 (More). More F 6
3.- Pulse F1 (AVG On) para activar el modo
de Promedio. AVG
On Off 20
F 1 4.- El siguiente icono aparecerá en la parte
inferior de la pantalla:
Pasos a realizar (Método 1)
5.- Introduzca el número de promediados utilizando las teclas numéricas.
µ
1.- Pulse la tecla BW.
BW
2.- Pulse F4 (AVG On) para activar el modo de Promedio.
AVGOn Off
20 F 4
Método 2
3.- Introduzca el tiempo promedio utilizando las teclas numéricas.
µ
Rango 1 ~ 100
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 74 02/2007
Ejemplo: después de promediado
Promediado 20 veces
6.3.6.2 Desplazar Marcador a Trazo
1.- Compruebe el Marcador activo en la esquina superior derecha de la pantalla.
2.- Pulse la tecla Marker. Marker
3.- Pulse F6 (More)
More F 6
Pasos a realizar
4.- Pulse F1 (Marker Trace). Marker TraceAuto A B C F 1
Rango Auto El Marcador se desplaza a la señal o trazo activo.
Trazo A El Marcador se desplaza para Trazo A.
Trazo B El Marcador se desplaza para Trazo B.
Trazo C El Marcador se desplaza para Trazo C.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 75
Pantalla Marcador en Trazo C
• Guardar/Copiar/Eliminar/Renombrar archivo de trazo Información general
Los archivos de trazo se pueden guardar, copiar, eliminar o renombrar utilizando las herramientas de archivo. Pulse la tecla de File para tener acceso a cada función.
File
Guardar/ Copiar
Pulse F1 (Copy). Copy... F 1
Eliminar Pulse F2 (Delete).
Delete... F 2 Renombrar Pulse F3 (Rename).
Rename... F 3
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 76 02/2007
6.3.6.3 Utilizar funciones Matemáticas con Trazos Información general
Se pueden realizar varias operaciones matemáticas entre Trazo A y
Trazo B. Ambos trazos deben ser activados previamente. Después de
la operación matemática, el modo de trazos cambia a visualización. 1.- Pulse la tecla Trace.
Trace 2.- Pulse F6 (More).
More F 6 3.- Pulse F2 (Trace Math).
Trace Math.. F 2
4.- Seleccione el tipo de la operación matemáticas de F1 ~ F5.
A↔B: intercambia trazo A y trazo B. A+B→A: Suma trazo A y trazo B. A-B→A: Resta trazo B de trazo A. A+const→A: Añade un valor constante a
trazo A. A-const→A: Resta un valor constante de
trazo A.
A B F 1
A+B A F 2
A-B A F 3
A+const A F 4
A-const A F 5 5.- Cuando seleccione A+const / A- const
introduzca el valor constante utilizando las teclas numéricas.Rango: -40 ~ +40dB
µ
Pasos a realizar
6.- El siguiente icono aparecerá en la parte inferior de la pantalla:
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 77
Ejemplo:
A↔B
Ejemplo:
A+B→A
Ejemplo:
A-B→A
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 78 02/2007
Ejemplo:
A+Constante → A (5 dB)
Ejemplo:
A-Constante → A (5 dB)
6.3.6.4 Seleccionar Modo de Detección de Señal Información general
Para mostrar la señal entrante en pantalla, el equipo convierte primero
la señal de entrada a una señal de vídeo, la digitaliza, luego utiliza un
detector para recoger las muestras. Configurando el modo de
detección, algunas señales se visualizarán con más nitidez. 1.- Pulse la tecla Trace. Trace
Pasos a realizar
2.- Pulse F6 (More). More F 6
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 79
3.- Pulse F3 (Detection). Detection.. F 3
4.- Seleccione el tipo de detección de señal
de F1 ~ F5. Vea abajo la descripción de cada
tipo..
Normal F 1
Sample F 2
Peak+ F 3
AVG F 4
QPeak F 5
4.- Pulse F6 (Return) para volver al menú
anterior. Return F 6
Parámetro Normal Modo predeterminado. Cuando el nivel de señal
aumenta o disminuye constantemente, detecta los
picos positivos. De no ser así, el modo de
detección cambia de picos positivos a picos
negativos. Útil para recoger fenómeno de ráfaga
evitando ruido excesivo.
Muestra Detecta señales al azar. Útil para detectar
parecidas a un ruido, pero tiende a no detectar
fenómenos de ráfaga.
Pico + Detecta señales de pico positivas. Útil para
(pico positivo) detectar señales sinusoidales, pero tiende a
detectar más ruido que otros modos.
AVG (promedio) Disponible cuando el filtro EMI (opcional) está
instalado. Detecta el nivel de energía promedio de
las muestras, utilizando un filtro de paso bajo. Útil
para reducir el nivel del ruido. Para más detalles
de filtro EMI.
Qpeak
(cuasi pico) Disponible cuando el filtro EMI (opcional) está
instalado. Detecta el nivel de energía del cuasi-
pico máximo de las muestras. Útil para visualizar
en Span cero sin perder variaciones de señal.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 80 02/2007
Ejemplo Modo de detección Normal
Modo de detección de Muestra
Modo de detección de Pico +
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 81
6.3.7 MEDIDAS DE POTENCIA
La función de Medidas de potencia incluye cuatro tipos de medidas complejas utilizadas con frecuencia: ACPR, OCBW, N dB y Oscilaciones de Fase. Cada medida es configurable y se actualiza en tiempo real.
6.3.7.1 Medida ACPR
• Descripción
Información general
El ACPR (Nivel de Potencia de Canal Adyacente), también llamado
ACLR (Nivel de Fugas de Canal Adyacente), se refiere a la cantidad de
potencia perdida, que proviene del canal de radio principal que afecta a
los canales adyacentes como distorsión de señal. Árbol de menú
ACPROn Off F 2
CH Up F 4
CH Down F 5
ChannelSetup... F 1 CH BW F 1
CH SPC F 2
ADJ CHOffset... F 4
Adj CH BW1 F 1
Adj CH Offs1 F 2
Return F 6
Adj CH BW2 F 3
Adj CH Offs2 F 4
Meas
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 82 02/2007
Parámetro Ancho de banda de canal: Ancho de banda de frecuencia ocupado
canal a medir. 1 kHz ~ 3.0GHz
Espacio de canal Distancia de frecuencia entre los canales
principales. 1 kHz ~ 3.0GHz
Ancho de banda de canal adyacente 1 y 2 Ancho de banda de
frecuencia que los canales adyacentes 1 y 2 ocupan. 1 kHz ~ 3.0GHz
Compensación de canales adyacentes 1 y 2 La distancia de
frecuencia entre los canales adyacente 1 y 2 y el canal principal. 1 kHz
~ 3.0GHz 6.3.7.2 Procedimiento para medidas ACPR
1.- Pulse la tecla Meas. Meas 2.- Pulse F2 (ACPR On). ACPR
On Off F 2 3.- La pantalla cambia a modo ACPR, mostrando y actualizando el
resultado de ACPR en la mitad inferior.
1. Activar ACPR
InferiorACPR 1
SuperiorACPR 1
ACPR 2 Inferior
ACPR 2 Superior
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 83
1.- Pulse F1 (Channel Setup). ChannelSetup... F 1
2.- Pulse F1 (CH BW). CH BW F 1 3.- Introduzca el ancho de banda del canal
(en MHz) utilizando las teclas numéricas.
Rango: 1 kHz ~ 3.0GHz
µ
2. Ajustar el BW (ancho de banda) del canal
4.-El valor se actualiza en la columna de
ancho de banda del canal.
1.- Pulse F2 (CH SPC). CH SPC F 2
2.- Introduzca el espacio del canal (en MHz)
utilizando las teclas numéricas.
Rango: 1 kHz ~ 3.0GHz
µ
3. Ajustar el espacio del canal
3.- El valor se actualiza en la columna de
Espacio del canal. 1.- Pulse F4 (ADJ CH Offset). ADJ CH
Offset... F 4
2.- Pulse F1 (Adj CH BW1). Adj CH BW1 F 1 3.- Introduzca el ancho de banda del canal
(en MHz) utilizando las teclas numéricas.
Rango: 1 kHz ~ 3.0GHz
µ
4. Ajustar Ancho de banda del canal 1 adyacente
4.- El valor se actualiza en la columna Adj
CH BW1.
1.- Pulse F2 (Adj CH Offs1) Adj CH Offs1 F 2
2.- Introduzca la compensación del canal 1
adyacente, utilizando las teclas numéricas.
Rango: 1 kHz ~ 3.0GHz
µ
5. Ajustar compensación del canal 1 adyacente
3.- El valor se actualiza en la columna Adj
CH Offset1.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 84 02/2007
1.- Pulse F3 (Adj CH BW2). Adj CH BW2 F 3
2.- Introduzca el ancho de banda del canal 2
adyacente, utilizando las teclas numéricas.
Rango: 1 kHz ~ 3.0GHz
µ
6. Ajustar Ancho de banda del canal 2 adyacente
3.- El valor se actualiza en la columna Adj
CH BW2 1.- Pulse F4 (Adj CH Offs2). Adj CH Offs2 F 4
2.- Introduzca la compensación del canal 2
adyacente, utilizando las teclas numéricas.
Rango: 1 kHz ~ 3.0GHz
µ
7. Ajustar compensación del canal 2 adyacente
3.- El valor se actualiza en la columna Adj
CH Offset2. 1.- Pulse F6 (Return) dos veces Return F 6
x2
8. Mover canal arriba / abajo
2.- Pulse F4 (CH Up) o F5 (CH Down) para
cambiar la medida al siguiente canal. CH Up F 4
CH Down F 5
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 85
6.3.7.3 Medida OCBW
• Descripción Información general
El OCBW (Ancho de banda Ocupada) es el ancho de banda del canal
que consume (ocupa) la cantidad especificada de potencia. Árbol de menú
CH BW F 1
CH SPC F 2
CH Up F 4
CH Down F 5
ChannelSetup...
F 1
Return F 6
OCBWOn Off F 3 OCBW % F 3
Meas
Parámetro Ancho de banda de canal: El ancho de banda de frecuencia que el
canal ocupa.
1 kHz ~ 3.0GHz, resolución de 1 kHz.
Espacio de canal La distancia de frecuencia entre los canales
principales.
1 kHz ~ 3.0GHz, resolución de 1 kHz.
% de OCBW La proporción de ancho de banda ocupada respecto a la
cantidad de potencia consumida.
0.0 % ~ el 100.0 %, resolución del 0.1 %
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 86 02/2007
• Procedimiento para medidas OCBW
1.- Pulse la tecla Meas. Meas 2.- Pulse F3 (OCBW On). OCBW
On Off F 3 3.- La pantalla cambia a modo OCBW, mostrando y actualizando el
resultado de OCBW en la mitad inferior.
1. Activar OCBW
OCBW
Potencia de Canal
1.- Pulse F1 (Channel Setup). ChannelSetup... F 1
2.- Pulse F1 (CH BW). CH BW F 1 3.- Introduzca el ancho de banda del canal
(en MHz) utilizando las teclas numéricas.
Rango: 1 kHz ~ 3.0GHz
µ
2. Ajustar Ancho de banda del canal
4.-El valor se actualiza en la columna de
ancho de banda del canal.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 87
1.- Pulse F2 (CH SPC). CH SPC F 2
2.- Introduzca el espacio del canal (en MHz)
utilizando las teclas numéricas.
Rango: 1 kHz ~ 3.0GHz
µ
3. Ajustar el espacio del canal
3.- El valor se actualiza en la columna de
Espacio del canal. 1.- Pulse F3 (OCBW %). OCBW % F 3
2.- Introduzca el % OCBW utilizando las
teclas numéricas y la tecla Enter.
Rango: 0,0 % ~ 100 %
µ
4. Ajustar el % de OCBW
3.- El valor se actualiza en la columna OCBW
%.
1.- Pulse F6 (Return) dos veces. Return F 6
5. Mover canal arriba / abajo
2.- Pulse F4 (CH Up) o F5 (CH Down) para
cambiar la medida al siguiente canal. CH Up F 4
CH Down F 5 6.3.7.4 Medida N dB Información general
N dB es el ancho de banda de frecuencia de un canal que cubre la
amplitud especificada. Parámetro N dB : 0,1dB ~ 80,0dB, resolución de 0,1dB
1.- Pulse la tecla Meas. Meas 2.- Pulse F6 (More). More F 6 3.- Pulse F1 (N dB BW On). N dB BW
On Off F 1
1. Activar N dB
4.- La pantalla cambia a modo N dB, mostrando y actualizando el
resultado de N dB en la mitad inferior.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 88 02/2007
Ancho de banda 3 dB
1.- Pulse F2 (NdB) para ajustar la amplitud
cubierta por el ancho de banda. N dB F 2
2.- Introduzca la amplitud utilizando las teclas
numéricas.
Rango: 0.1dB ~ 70.0dB
µ
2. Ajustar amplitud
3.- Pulse F1 (N dB BW On). N dB BWOn Off F 1
6.3.7.5 Medida de Oscilación de Fase (Phase Jitter) Información general
La Oscilación de Fase es la cantidad de fluctuación de fase que
acortan o alargan la frecuencia central. Parámetro Compensación inicial: Compensación de frecuencia inicial en
referencia a la frecuencia central.
0.0MHz ~ ½ de Span, resolución de 0.1MHz.
Compensación final: Compensación de frecuencia final en referencia
a la frecuencia central.
0.0MHz ~ ½ de Span, resolución de 0.1MHz. 1.- Pulse la tecla Meas. Meas
1. Activar Oscilación de Fase
2.- Pulse F6 (More). More F 6
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 89
3.- Pulse F3 (Phase Jitter On). Phase JitterOn Off F 3
4.- La pantalla cambia a modo de oscilación de fase, mostrando y
actualizando el resultado de oscilación de fase en la mitad inferior.
Fluctuación de fase
Fluctuación de tiempo
1.- Pulse F4 (Phase Jitter Setup) Phase JitterSetup F 4
2.- Pulse F1 (Start Offset) y F2 (Stop Offset)
para ajustar el valor de la compensación
inicial /final.
StartOffset F 1
StopOffset F 2
2. Ajustar compensación inicial /final
3.- Introduzca la compensación utilizando las
teclas numéricas.
Rango: 0,0MHz ~ ½ de Span
µ
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 90 02/2007
6.3.8 LÍNEA DE LÍMITE
La Línea de Límite ajusta el límite de amplitud superior e inferior sobre el rango de frecuencia total. Las líneas de límite se pueden usar para detectar si el nivel de señal de entrada está por encima, por debajo, o dentro de la amplitud deseada. El resultado, Pasa o No pasa, se muestra en la parte inferior de la pantalla en tiempo real.
6.3.8.1 Editar la Línea de Límite Parámetro Editar punto: Se puede editar un máximo de 10 puntos para cada
línea de límite Alta y Baja.
Frecuencia: 9 kHz ~ 3.0GHz por punto editado.
Amplitud: Por edición de punto:
-130 ~ +20dBm
-83.01dBmV ~ +66.99dBmV
-23.01dBuV ~ +126.99dBuV 1. Activar Línea de Límite
1.- Pulse la tecla Limit Line.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 91
2.- Pulse F1 (H Limit On) y/o F2 (L Limit On)
para activar la línea de límite Alta / Baja.
H LimitOn Off F 1
L LimitOn Off F 2
3.- La línea de límite aparece en pantalla.
Azul: —— línea de límite Alta (A)
Amarillo: —— línea de límite Baja (B)
Línea de límite A (editada)
Línea de límite B
1.- Pulse F3 (Edit). Edit... F 3
2.- Pulse F1 (Limit) para seleccionar la línea
de límite a editar.
LimitLow High F 1
2. Activar la Tabla de edición de líneas de límite
3.- Pulse F2 (Edit Table On). La Tabla de
edición aparece en la mitad inferior de la
pantalla.
Edit TableOn Off F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 92 02/2007
1.- Asegúrese que el cursor señala al primer
punto de frecuencia vacío. Utilice las teclas
Arriba / Abajo para mover el cursor, si es
necesario.
Hay 10 puntos disponibles para cada línea de
límite Alta y Baja.
No. MHz dBm12345
2.- Si es necesario, mueva el cursor a
distintos puntos de frecuencia utilizando las
teclas Direccionales.
3.- Introduzca la frecuencia en MHz utilizando
las teclas numéricas.
9.0 kHz ~ 3.0GHz.
µ
4.- El cursor se mueve automáticamente al
lado de Ganancia. Introduzca la ganancia en
dB utilizando las teclas numéricas.
Rango: -130dB ~ +20dBm
No. MHz dBm12345
98
3a. Añadir un punto de línea de límite
5.- Repita los pasos anteriores para los
puntos que necesite.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 93
1.- Sitúe el cursor en el punto a eliminar
utilizando las teclas Direccionales
2.- Pulse la tecla F3 (Delete) para suprimir el
punto (frecuencia y amplitud a la vez). Delete F 3
No. MHz dBm12345
100-40
102
98-30-40
No. MHz dBm12345
-4010298
-40
3b. Eliminar un punto de línea de límite
3.- Para deshacer la eliminación, pulse F5
(Undelete). Undelete F 5
1.- Pulse F4 (Delete All). Delete All.. F 4
2.- Pulse F1 (No) o F2 (Yes) para confirmar
la eliminación. Los 10 puntos de línea de
límite serán eliminados.
No F 1
Yes F 2
3.- Pulse F6 (Return) para volver al menú
anterior. Return F 6
3c. Eliminar todos los parámetros de línea de límite
4.- Para deshacer la eliminación, pulse F5
(Undelete). Undelete F 5
4. Cambiar entre Línea de límite Alta / Baja
Si es necesario, pulse F1 (Limit) para
comenzar a editar la otra línea de límite.
Repita los pasos anteriores.
LimitLow High F 1
Ejemplo Parámetros de Línea de límite (Alta)
Punto No. Frecuencia (MHz) Amplitud (dBm)
1 98MHz -40dBm
2 100MHz -30dBm
3 102MHz -40dBm
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 94 02/2007
Línea resultante
6.3.8.2 Ejecutar Test Pasa-No Pasa
Esta sección asume que la línea de límite ya está definida.
Comprueba si la amplitud de toda la forma de onda
está entre la línea de límite Alta y la línea de límite
Baja.
Comprueba si la amplitud de pico de la forma de onda
está entre la línea de límite Alta y la línea de límite
Baja.
Condiciones Pasa-No Pasa
Comprueba si la amplitud mínima de la forma de onda
está entre la línea de límite Alta y la línea de límite
Baja.
1.- Seleccionar condiciones Limit Line 1. Seleccionar condiciones
2.- Pulse F5 (Pass/Fail) repetidamente
para seleccionar la condición.
Pass/Fail F 5
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 95
1.- Pulse F4 (Pass/Fail On) para activar el
test.
Pass/FailOn Off F 4
2. Ejecutar Test Pasa-No Pasa
2.- El resultado del test aparece en la parte
inferior de la pantalla. Pantalla Resultado: No Pasa
Nota: Si la línea de límite Alta o Baja no está definida, el test Pasa-No Pasa usa el
nivel de pantalla más alto o más bajo como línea de límite.
6.3.8.3 Guardar/Copiar/Eliminar/Renombrar archivo de línea de
límite Información general
Los archivos de línea de límite se pueden
guardar, copiar, eliminar o renombrar
utilizando las herramientas de archivo. Pulse
la tecla File para tener acceso a cada
función.
File
Copiar Pulse F1 (Copy). Copy... F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 96 02/2007
Eliminar Pulse F2 (Delete). Delete... F 2
Renombrar Pulse F3 (Rename). Rename... F 3
6.3.9 ANCHO DE BANDA
El Ancho de Banda (BW) determina cómo el equipo clasifica los distintos picos estrechos de señal (resolución) y la velocidad de actualización de la pantalla (tiempo de barrido). Se puede promediar la forma de onda para suavizar el nivel del ruido. La resolución y el tiempo de barrido se compensan uno al otro de modo que hay que configurarlos con mucho cuidado.
6.3.9.1 Seleccionar RBW (Resolución de Ancho de banda) Información general
El RBW (Resolución de Ancho de Banda) define la anchura del filtro FI
(frecuencia intermedia) que se usa para separar picos de señal los
unos de los otros. Cuanto más estrecha la RBW, mayor será la
capacidad de separar señales en frecuencias cercanas, pero también
aumenta el tiempo de barrido bajo un Span de frecuencia determinado;
la pantalla se actualizada con menos frecuencia.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 97
1.- Pulse la tecla BW. BW
2.- Pulse F1 (RBW) para seleccionar Auto o
Manual.
RBWAuto Manu F 1
3.- Cuando Manu (manual) está
seleccionado, utilice las teclas Direccionales
o el Selector rotativo para cambiarlo.
Pasos a realizar
4.- La RBW seleccionada aparece en la
ventana de comandos.
RBW: 30kHz
Modo Auto La RBW se ajusta automáticamente.
Manual La RBW se ajusta manualmente. El icono BW aparece
en la parte inferior de la pantalla.
Rango RBW Span recomendado Estándar / Opcional
300 Hz Span <30 kHz Opcional (RBW de 300 Hz)
3 kHz Span <300 kHz Estándar
9 kHz 300kHz≤Span <600 kHz Opcional (Filtro EMI)
10 kHz 300kHz≤Span <1MHz Opcional (10k/RBW de 100
kHz)
30 kHz 300kHz≤Span <6MHz Estándar
100 kHz 6MHz≤Span <20MHz Opcional (10k/100kHz RBW)
120 kHz 6MHz≤Span <19MHz Opcional (Filtro EMI )
300 kHz 6MHz≤Span <60MHz Estándar
4MHz 60MHz≤Span Estándar 1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
Comprobar estado de instalación de la RBW
3.- Pulse F4 (System Config On) para
activar la ventana de configuración de
sistema.
System ConfigOn Off F 4
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 98 02/2007
Elementos Opcionales
4.- Compruebe la zona de elementos opcionales para ver el estado de
la instalación de la RBW (Marcado: instalado, En blanco: no instalado).
Instalado No instalado
5.- Pulse F4 (System Config Off) para cerrar la
ventana de configuración de sistema. System ConfigOn Off F 4
Nota: Los 9k/120kHz RBW (Filtro EMI) y los 10k/100kHz RBW son
exclusivos; no pueden ser instalados juntos. Para instalar una nueva
opción RBW, póngase en contacto con personal cualificado. 6.3.9.2 Seleccionar VBW (Ancho de banda de Vídeo) Información general
El VBW (Ancho de Banda de Vídeo) define la suavidad del trazo en la
pantalla. Combinado con RBW, el Ancho de Banda de Vídeo define la
capacidad de distinguir la señal del ruido circundante o picos los
adyacentes. 1.- Pulse la tecla BW. BW
2.- Pulse F2 (VBW) para seleccionar Auto o
Manual.
VBWAuto Manu F 2
Pasos a realizar
3.- Cuando Manu (manual) está
seleccionado, utilice las teclas Direccionales
o el Selector rotativo para cambiarlo.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 99
4.- El VBW seleccionado aparece en la
ventana de comandos.
VBW: 1kHz
Modo Auto: El VBW se ajusta automáticamente.
Manual: El VBW se ajusta manualmente. El icono BW aparece
en la parte inferior de la pantalla.
Rango 10 Hz, 1 kHz, 10 kHz, 100 kHz, 300 kHz
VBW se selecciona automáticamente según la RBW en modo
Automático. Nota El equipo cambia automáticamente el VBW según la selección de la
RBW. 6.3.9.3 Contenidos del Modo de Auto de RBW/VBW Información general
* Utilice la siguiente información para seleccionar manualmente los
ajustes de VBW y RBW.
* El rango de RBW/VBW cambia según la configuración del sistema,
especialmente en casos de instalación de elementos opcionales.
1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
Comprobar estado de instalación de la RBW
3.- Pulse F4 (System Config On) para
activar la ventana de configuración de
sistema.
System ConfigOn Off F 4
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 100 02/2007
Elementos Opcionales
4.- Pulse F4 (System Config Off) para
cerrar la ventana de configuración de
sistema.
System ConfigOn Off F 4
Configuración estándar
Elemento opcional Instalar Configuración
Filtro EMI (9k/120k RBW) No RBW de 300 Hz No 10k/100kHz RBW No
Span
RBWVBW
3k10k
30k 4M10k 300k
300k 6M 60M 3G0
300k100k
(Logarithmic scale, unit in Hz)
Configuración Estándar + 9k/120kHz RBW
Elemento opcional Instalar Configuración
Filtro EMI (9k/120k RBW) Si RBW de 300 Hz No 10k/100kHz RBW No
30k3k10k
9k 4M10k 300k
300k 600k 6M 60M 3G0 19M
120k 300k10k 100k 100k
(Logarithmic scale, unit in Hz)
Span
RBWVBW
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 101
Configuración Estándar + 300/9k/120kHz RBW
Elemento opcional Instalar Configuración
Filtro EMI (9k/120k RBW) Si RBW de 300 Hz Si 10k/100kHz RBW No
30k3001k
3k 9k 4M10k 10k 300k
300k 600k 6M 60M0 19M
120k 300k10k 100k 100k
(Logarithmic scale, unit in Hz)
3G30kSpan
RBWVBW
Configuración Estándar + 10k/100kHz RBW
Elemento opcional Instalar Configuración
Filtro EMI (9k/120k RBW) No RBW de 300 Hz No 10k/100kHz RBW Si
30k3k10k
10k 4M10k 300k
300k 1M 6M 60M0 20M
100k 300k10k 100k 100k
(Logarithmic scale, unit in Hz)
3GSpan
RBWVBW
Configuración Estándar + 300/10k/100kHz RBW
Elemento opcional Instalar Configuración
Filtro EMI (9k/120k RBW) No RBW de 300 Hz Si 10k/100kHz RBW Si
30k
30k3001k
10k 4M10k 300k
300k 1M 6M 60M0 20M
100k 300k10k 100k 100k
(Logarithmic scale, unit in Hz)
3G
3k10k
Span
RBWVBW
6.3.9.4 Ajustar Tiempo de Barrido Información general
El Tiempo de Barrido define la tasa de actualización de la pantalla.
Tenga en cuenta que el tiempo de barrido y RBW/VBW se compensan
mutuamente. Un tiempo de barrido más rápido actualiza la pantalla con
más frecuencia, pero hace más anchos la RBW y el VBW, reduciendo
la capacidad de separar señales en frecuencias cercanas.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 102 02/2007
1.- Pulse la tecla BW. BW
2.- Pulse F3 (Swp tm) para cambiar entre
ajustes Auto y Manual.
Swp tmAuto Manu F 3
En modo Manual, el Icono de Tiempo de Barrido Manual aparece
en pantalla.
Pasos a realizar
3.- Cuando seleccione el modo Manual,
introduzca el tiempo de barrido utilizando las
teclas numéricas.
µ
Modo Auto: El tiempo de barrido está ajustado automáticamente.
Manual: El tiempo de barrido está ajustado manualmente. Rango 50ms ~ 12.8s, resolución de 1us
Nota En el modo Automático, el equipo está optimizado para un tiempo de barrido rápido. Para ajustes RBW más estrechos, como 300 Hz y 3 kHz, esta optimización causará un ligero aumento del ruido de fase. Para reducir el nivel de ruido de fase, por favor ralentice el tiempo de barrido utilizando el ajuste manual.
6.3.9.5 Forma de onda Promediada Información general
El equipo hace un promedio de la forma de onda según el número configurado y luego lo muestra en la pantalla. Esta función suaviza mucho el nivel de ruido, pero ralentiza la tasa de actualización de la pantalla.
1.- Pulse la tecla BW. BW
2.- Pulse F4 (AVG On) para activar el modo
de Promedio.
AVGOn Off
20 F 4
Pasos a realizar (Método 1)
3.- Introduzca el tiempo promedio utilizando
las teclas numéricas.
µ
1.- Pulse la tecla Trace. Trace 2.- Pulse F6 (More). More F 6
Pasos a realizar (Método 2)
3.- Pulse F1 (AVG On) para activar el modo
de Promedio.
AVGOn Off
20F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 103
4.- El icono de modo de promedio aparece en
la parte inferior de la pantalla.
5.- Introduzca el tiempo promedio utilizando
las teclas numéricas.
µ
Parámetro 1 ~ 200: Sólo disponible cuando el Promedio está activado.
• Reiniciar RBW/VBW/Tiempo de Barrido a Auto
1.- Pulse la tecla BW. BW
Pasos a realizar
2.- Pulse F5 (All Auto). Los ajustes de RBW,
VBW y Tiempo de barrido cambian a Auto. All Auto F 5
Ajustar
RBW/VBW/
Tiempo de
Barrido
después de
Autoset
Los tres parámetros BW (RBW, VBW y Tiempo de Barrido) serán
reiniciados a modo Auto cuando se use Autoset, sin tener en cuenta
sus ajustes anteriores.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 104 02/2007
6.3.10 DISPARO(Trigger)
La función de Disparo (Trigger) ajusta las condiciones de señal que usa el equipo para realizar un disparo y capturar formas de onda con sus respectivas frecuencias, amplitudes y retrasos. Se pueden utilizar señales externas si se requieren condiciones especiales.
6.3.10.1 Ejecución Libre (Predeterminada)
En Ejecución Libre, el equipo captura todas las señales entrantes (sin
condiciones de disparo).
1.- Pulse la tecla Trigger. Trigger
Pasos a realizar
2.- Pulse F1 (Free Run). Free Run F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 105
6.3.10.2 Activar disparo por vídeo
1.- Pulse la tecla Trigger. Trigger
2.- Pulse F2 (Trigger Condition). Seleccione
Video.
TriggerCondition
Video Ext.F 2
3.- El icono de disparo por vídeo aparece en
la parte inferior de la pantalla.
4.- Introduzca el nivel de disparo (amplitud)
utilizando las teclas numéricas. El valor
aparece en la ventana de comandos.
µ
Video: -20dBm
5.- Pulse F5 (Trigger Freq) para ajustar la
frecuencia con la cual el equipo comprueba
las condiciones de disparo.
Trigger Freq1.5GHz F 5
6.- Introduzca la frecuencia de disparo
utilizando las teclas numéricas.
µ
Pasos a realizar
7.- Para desactivar el disparo, pulse F1 (Free
Run). Free Run F 1
Rango de nivel de disparo
dBm -130 ~ +20dBm
dBmV -83.01 ~ +66.99dBmV
dBµV -23.01 ~ +126.99dBµV Rango de frecuencia de disparo
0 ~ 3.0GHz
6.3.10.3 Activar el disparo externo
1.- Pulse la tecla Trigger. Trigger
Pasos a realizar
2.- Pulse F2 (Trigger Condition). Seleccione
Ext.
TriggerCondition
Video Ext.F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 106 02/2007
3.- El icono de disparo externo aparece en la
parte inferior de la pantalla.
4.- Conecte la señal de disparo externa al
terminal del panel trasero. El flanco positivo
entre 0V y 5V provoca el disparo.
Rango de nivel de entrada
0 ~ 5V, disparo de flanco positivo
6.3.10.4 Seleccionar el modo de disparo
1.- Pulse la tecla Trigger. Trigger
2.- Pulse F3 (Trigger Mode) repetidamente
para elegir entre los modos de disparo.
Trigger ModeNorm. Sgl. Cont. F 3
Pasos a realizar
3.- Cuando seleccione Sgl (único) o Cont.
(continuo), puede usar F6 (Run Now) para
ejecutar manualmente el disparo.
Run Now F 6
Modos Normal: El equipo captura la señal cada vez que hay condiciones de
disparo
Único: El equipo captura la señal cuando la primera condición de
disparo ocurre, luego deja de capturar.
Continuo: El equipo captura la señal cuando la primera condición de
disparo ocurre, entonces cambia al modo de Ejecución Libre; sigue
capturando todas las señales de entrada sin tener en cuenta sus
condiciones.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 107
6.3.10.5 Ajustar retraso de disparo Información general
El retraso de disparo ajusta la cantidad de tiempo entre el momento de
la condición de disparo y el momento en que el equipo empieza a
capturar la señal.
1.- Pulse la tecla Trigger. Trigger
2.- Pulse F4 (Trigger Delay). Trigger Delay1000ms F 4
Pasos a realizar
3.- Introduzca el tiempo de retraso utilizando
las teclas numéricas.
µ
Rango de retraso
0, 10µs ~ 100s, resolución de 1µs
6.3.11 PANTALLA
El ajuste de pantalla configura el nivel de brillo de la pantalla LCD y la distribución de la información de la pantalla, incluyendo la línea de pantalla, el título y división de ventana. La línea de pantalla proporciona una línea de referencia adecuada para medir la amplitud. La división de ventana permite que dos formas de onda se muestren en pantalla de forma simultánea. El terminal VGA en el panel trasero permite extraer el contenido de la pantalla LCD con una resolución de 640x480.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 108 02/2007
6.3.11.1 Cambiar el Brillo de la Pantalla
1.- Pulse la tecla Display. Display
2.- Pulse F1 (LCD Dimmer). LCD Dimmer F 1
Pasos a realizar
3.- Ajuste el brillo utilizando las teclas
Izquierda/Derecha o el Selector rotativo.
Rango 0 (más oscuros) ~ 5 (más brillante)
6.3.11.2 Activar Línea de Pantalla
1.- Pulse la tecla Display. Display
2.- Pulse F2 (Display Line On). Display LineOn Off F 2
3.- La línea aparece en la pantalla.
Línea de pantalla
Pasos a realizar
4.- El nivel de línea de pantalla aparece en la
ventana de comandos.
Display Line:-50dB
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 109
5.- Puede mover la línea utilizando las teclas
Direccionales o el Selector rotativo.
La línea de pantalla no está disponible cuando la pantalla está dividida. Nota
División de ventana Editar Línea de límite
Medidas de potencia 6.3.11.3 Introducir Título de Pantalla
1.- Pulse la tecla Display. Display
2.- Pulse F2 (Title). Title... F 3
3.- Seleccione el tipo de caracteres de F2 ~
F4.
(Capital Letter)
F 2
(Small Letter)
F 3
(Symbol) F 4
4.- Para introducir la letra “S” en mayúsculas,
pulse F2 (Capital Letter) repetidamente
hasta que el cursor alcance la “S”.
(Capital Letter)
F 2
Q R S T U
5.- Prensa la tecla Enter. La “S” aparece en
la ventana de comandos. TL S
6.- Siga los pasos anteriores hasta introducir
todos los caracteres.
TL SATEST
(SATEST)
7.- Pulse F5 (Show Title). Show Title F 5
8.- El título introducido aparece en la esquina
superior izquierda de la pantalla.
Pasos a realizar
9.- Para borrar el título, pulse F1 (Clear
Title). Clear Title F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 110 02/2007
Parámetro Mayúsculas: Alfabeto en mayúsculas, de A a Z.
Minúsculas: Alfabeto en minúsculas, de a a z.
Símbolos: Los 14 símbolos más utilizados se muestran a continuación.
\ # / _ - . * : ( ) < > %
6.3.11.4 División de Pantalla
1.- Pulse la tecla Display. Display
2.- Pulse F4 (Split Window). Split Window...
F 4
Pasos a realizar
3.- La ventana se divide en ventana superior e inferior. La ventana
inferior retiene la escala vertical y horizontal originales. La ventana
superior muestra la escala completa.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 111
4.- Seleccione la ventana activa (la forma de
onda se actualiza) pulsando F1 (Upper) o F2
(Lower). Pulsando F3 (Alternate Sweep) se
actualizan ambas ventanas alternativamente.
Upper F 1
Lower F 2
AlternateSweep
F 3
5.- Para volver al modo de una sola ventana,
pulse F4 (Full Screen). La ventana que se
encuentra activa en este momento se amplía.
Full Screen F 4
* La conmutación a Pantalla Completa (Full Screen) del modo de
Barrido Alternativo (Alternate Sweep) no es recomendable, ya que no
se puede predecir qué ventana, si la superior o la inferior, será
seleccionada. 6.3.11.5 Utilizar la Salida VGA Pasos a realizar
Conecte un monitor externo al terminal VGA
del panel trasero. La salida está siempre
activada.
Parámetro Tipo de conector: VGA 15 pins, hembra
Resolución: 640 x 480 6.3.11.6 Imprimir Imagen de Pantalla
La forma de onda visualizada en la pantalla se imprimirá en una impresora
externa.ç
1.- Conecte la impresora al terminal USB del
panel delantero.
Pasos a realizar
Compatibilidad: USB 1.1/2.0
Conector: Tipo A, hembra
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 112 02/2007
1.- Pulse la tecla File. File
2.- Pulse F4 (Print screen). Print Screen.. F 4
3.- Pulse F1 (To Printer). La pantalla se
imprimirá como una imagen de mapa de bits. To Printer F 1
6.3.11.7 Guardar la Imagen de la Pantalla en una memoria USB
1.- Conecte la impresora al terminal USB del
panel delantero.
Compatibilidad: USB 1.1/2.0
Conector: Tipo A, hembra 2.- Pulse la tecla File. File
3.- Pulse F4 (Print screen). Print Screen.. F 4
4.- Pulse F2 (To Ext. Memory) To Ext.Memory... F 2
5.- El contenido de la memoria USB aparece en la pantalla.
MyResultAMyPrintB
File Function: Print toFile
Item Name
Type: Memory External
RemarkMyPrintA
Pasos a realizar
6.- Para guardar la imagen de la pantalla,
pulse F2 (Print Now). Un nuevo archivo
*.bmp se creará en la memoria USB.
Print Now F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 113
7.- Si desea corregir el nombre del archivo,
pulse F1 (Edit File Name). Edit File Name F 1
8.- Una tabla que contiene todos los
caracteres aparece en la parte inferior de la
pantalla. Desplace el cursor por la tabla
utilizando la tecla Izquierda/Derecha y el
Selector rotativo. Pulse la tecla Enter para
confirmar el caracter.
Char TableABCDEFGHIJKLMNOPQRSTUVWXYZabcde f
g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
9.- Cuando acabe, pulse F1 (Edit File Name)
otra vez. De este modo confirmará el nombre
del archivo.
Edit File Name F 1
6.3.12 ARCHIVO/IMPRESIÓN
La función de archivo (File) gestiona las operaciones que pueden realizarse con un archivo: copiar, eliminar y renombrar. El archivo puede contener la forma de onda, la línea límite, la corrección de amplitud, la secuencia (macro definido por el usuario) y la configuración del sistema. La fuente de archivo y el destino pueden ser interno o externo (memoria USB). La función de impresión (Print) permite la impresión directa o la grabación de una imagen mediante el conector USB.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 114 02/2007
6.3.12.1 Localización y Tipo de Archivos.
Interno En la memoria interna del equipo. El número de archivos está fijado (ver abajo).
En una memoria USB conectada al terminal del panel
delantero. En este caso no hay ningún límite en el número
de archivos que pueden ser guardados.
Localización de archivo
Externo
El icono USB se enciende cuando se detecta una memoria USB.
Compatibilidad: USB 1.1/2.0
Conector: Tipo A, hembra
Trazo Datos del trazo de la forma de onda. Formato de archivo: *.tra Hay 13 archivos disponibles internamente: Trazo A/B/C (trazo actual), Trazo 1~10 (trazos guardados).
Límite Datos de Línea de límite. Formato de archivo: *.lmt 12 archivos están disponibles internamente: LimitHL (línea de límite alta actual), LimitHL1~5 (línea de límite alta guardada), LimitLL (línea de límite baja actual), LimitLL1~5 (línea de límite baja guardada).
Corrección Datos de corrección de amplitud. Formato de archivo: *.cor Hay 5 archivos disponibles: Corrección 1 ~ 5.
Seq Datos de secuencia. Formato de archivo: *.seq Hay 10 archivos disponibles: Secuencia 1 ~ 10.
Tipo de archivo
Sistema Datos de configuración de sistema. Formato de archivo: *.set Hay 10 archivos disponibles: Sistema 1 ~ 10.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 115
6.3.12.2 Copiar Archivo
1.- Para utilizar la memoria USB (para archivos externos) como origen o destino, conecte la memoria USB al terminal del panel frontal.
1. Conectar la memoria USB (para archivos externos)
El icono USB se enciende cuando se detecta una memoria USB. 1.- Pulse la tecla File.
File
2.- Pulse F1 (Copy). Copy... F 1
3.- Pulse F1 (Source). Aparece la ventana de copiar archivo de origen. Source.. F 1
Source
File Function: CopyItem Name
Type: MemoryRemark
4.- Seleccione el tipo de archivo de F1 ~ F5. Seleccione después Int (interno) o Ext (externo). La pantalla se actualiza en consecuencia. El ejemplo que viene a continuación muestra cómo trabajar con el archivo de Trazo (interno).
TraceInt. Ext.
F 1
LimitInt. Ext.
F 2
CorrectionInt. Ext.
F 3
Seq.Int. Ext.
F 4
SetupInt. Ext.
F 5
2. Seleccionar el archivo de origen
TraceCTraceB
SourceFile Function: CopyItem Name
Type: MemoryRemark
TraceA
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 116 02/2007
5.- Utilice las teclas Arriba/Abajo para mover el cursor a la posición de archivo de origen que desea copiar. (Ejemplo: TraceC seleccionado)
TraceCTraceB
SourceFile Function: CopyItem Name
Type: MemoryRemark
TraceA
6.- Pulse F6 (Return). La información del archivo de origen será guardada en la memoria.
Return F 6
7.- Pulse F2 (Destination). La ventana de copiar archivo de destino se activará (mitad inferior de la pantalla). El tipo de archivo se selecciona automáticamente según la selección de tipo de archivo de origen anterior.
Destination.. F 2
TraceCTraceB
SourceFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
TraceCTraceB
DestinationFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
Trace1Trace2Trace3
Trace1Trace2Trace3
3. Seleccionar el archivo de destino
8.- Utilice las teclas Arriba/Abajo para mover el cursor a la posición de archivo de destino que desea copiar. (Ejemplo: Trace1 seleccionado)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 117
TraceCTraceB
DestinationFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
Trace1 9.- Pulse F6 (Return). La información del archivo de destino será guardada en la memoria.
Return F 6
10.- Los archivos de origen y destino quedaran remarcados (Ejemplo: origen — TraceC, destino — Trace1)
TraceCTraceB
SourceFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
TraceCTraceB
DestinationFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
Trace1Trace2Trace3
Trace1Trace2Trace3
11.- Pulse F4 (Copy Now). Copy Now F 4
4.- Archivo de copia
12.- Si el atributo de archivo de destino (Remark) está vacío (empty), cambia a lleno (full).
TraceC emptyTraceB empty
DestinationFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA empty
Trace1 full
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 118 02/2007
13.- Sitúe el cursor encima del archivo utilizando las teclas Arriba/Abajo.
14.- Pulse F3 (Edit File Name).
Edit File Name F 3
15.- Una tabla que contiene todos los caracteres aparece en la parte inferior de la pantalla. Desplace el cursor por la tabla utilizando la tecla Izquierda/Derecha y el Selector rotativo. Pulse la tecla Enter para confirmar el caracter.
Char TableABCDEFGHIJKLMNOPQRSTUVWXYZabcde f
g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
Corregir el nombre de archivo (archivo externo, si es necesario)
16.- Cuando acabe, pulse F1 (Edit File Name) otra vez. De este modo confirmará el nombre del archivo.
Edit File Name F 3
6.3.12.3 Eliminar Archivo
1.- Para utilizar la memoria USB (para archivos externos) como origen o destino, conecte la memoria USB al terminal del panel frontal.
1.- Conectar la memoria USB (para archivos externos)
El icono USB se enciende cuando se detecta una memoria USB. 2.- Pulse la tecla File.
File
3.- Pulse F2 (Delete). Delete... F 2
4.- Pulse F1 (Type). Aparece la ventana de eliminación de archivo. Type... F 1
2. Seleccionar el archivo de origen
SourceFile Function: DeleteItem Name
Type: MemoryRemark
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 119
5.- Seleccione el tipo de archivo de F1 ~ F5.Seleccione entonces Int (interno) o Ext (externo). La pantalla se actualizada en consecuencia. El ejemplo que viene a continuación muestra cómo trabajar con el archivo de Trazo (interno).
TraceInt. Ext.
F 1
LimitInt. Ext.
F 2
CorrectionInt. Ext.
F 3
Seq.Int. Ext.
F 4
SetupInt. Ext.
F 5
TraceCTraceB
SourceFile Function: DeleteItem Name
Type: Memory InternalRemark
TraceA
Trace16.- Utilice las teclas Arriba/Abajo para mover el cursor a la posición de archivo. (Ejemplo: Trace1 seleccionado)
TraceCTraceB
SourceFile Function: DeleteItem Name
Type: Memory InternalRemark
TraceA
Trace1
7.- Pulse F6 (Return). La posición de archivo será guardada en la memoria Return F 6
8.- Pulse F2 (Delete Now). Delete Now F 2
3. Suprimir archivo
9.- Archivo interno: el atributo de archivo (Remark) cambia a vacío (empty). En caso del archivo externo, el archivo será eliminado.
TraceC fullTraceB full
SourceFile Function: DeleteItem Name
Type: Memory InternalRemark
TraceA full
Trace1 empty
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 120 02/2007
6.3.12.4 Renombrar Archivo Información general
La función de renombrar archivos se permite sólo para archivos externos (memoria USB). La función de renombrar está también disponible durante la copia de archivo y al guardar imagen de pantalla .
1.- Conectar la memoria USB (para archivos externos
Para utilizar la memoria USB (para archivos externos) como origen o destino, conecte la memoria USB al terminal del panel frontal.
El icono USB se enciende cuando se detecta una memoria USB. 1.- Pulse la tecla File.
File
2.- Pulse F3 (Rename). El contenido de la memoria USB aparece en la pantalla. Rename... F 3
3.- Sitúe el cursor sobre el archivo utilizando las teclas Arriba/Abajo.
4.- Pulse F3 (Edit File Name).
Edit File Name F 3
5.- Una tabla que contiene todos los caracteres aparece en la parte inferior de la pantalla. Desplace el cursor por la tabla utilizando la tecla Izquierda/Derecha y el Selector rotativo. Pulse la tecla Enter para confirmar el caracter.
Char TableABCDEFGHIJKLMNOPQRSTUVWXYZabcde f
g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
2. Seleccionar el archivo
6.- Cuando acabe, pulse F1 (Edit File Name) otra vez. De este modo confirmará el nombre del archivo.
Confirm F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 121
6.3.12.5 Imprimir Imagen de Pantalla
La forma de onda visualizada en la pantalla se imprime en una impresora
externa.
1.- Conecte la impresora al terminal USB del panel frontal.
El icono USB se enciende cuando se detecta una impresora USB.
2.- Pulse la tecla File. File
3.- Pulse F4 (Print Screen).
Print Screen.. F 4
Pasos a realizar
4.- Pulse F1 (To Printer). La pantalla se imprimirá como una imagen de mapa de bits.
To Printer F 1
6.3.12.6 Guardar Imagen de Pantalla en memoria USB
1.- Conecte una memoria USB al terminal USB del panel frontal.
El icono USB se enciende cuando se detecta una impresora USB.
2.- Pulse la tecla File. File
3.- Pulse F4 (Print Screen).
Print Screen.. F 4
Pasos a realizar
4.- Pulse F2 (To Ext. Memory). To Ext.Memory... F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 122 02/2007
5.- El contenido de la memoria USB aparece en la pantalla.
MyResultAMyPrintB
File Function: Print toFile
Item Name
Type: Memory External
RemarkMyPrintA
6.- Para guardar la imagen de pantalla, pulse F2 (Print Now). Se creará un nuevo archivo *.bmp en la memoria USB.
Print Now F 2
MyResultAMyPrintB
File Function: Print toFile
Item Name
Type: Memory External
RemarkMyPrintA
MyFigure7.- Si quiere corregir el nombre del archivo, pulse F1 (Edit File Name). Edit File Name F 1
8.- Una tabla que contiene todos los caracteres aparece en la parte inferior de la pantalla. Desplace el cursor por la tabla utilizando la tecla Izquierda/Derecha y el Selector rotativo. Pulse la tecla Enter para confirmar el caracter.
Char TableABCDEFGHIJKLMNOPQRSTUVWXYZabcde f
g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
9.- Cuando acabe, pulse F1 (Edit File Name) otra vez. De este modo confirmará el nombre del archivo.
Edit File Name F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 123
6.3.13 FUNCIÓN PRESET
Pulsando la tecla Preset, se devuelve el equipo al estado de configuración por defecto.
Frecuencia Centro: 1.5GHz
Inicio: 0Hz Final: 3GHz Paso: 1MHz
Span 3GHz Amplitud Nivel de Ref.: 0dBm
Unidad: dBm Corrección: OFF
Escala: 10dB/ Ganancia Externa: 0dB Entrada Z: 50 Ω
Autoset Nivel Min. Amplitud: Auto Span: Auto Marcador Marcador: OFF
Tabla de Marcadores: OFF Trazo de Marcador: Auto Todos los Marcadores: OFF
Búsqueda de Picos
Tabla de Picos: OFF Umbral de Pico: OFF
Ordenar Picos por: Frecuencia Rastrear Picos: OFF
Trazo Trazo: A Promedio: OFF
Modo: Eliminar Detección: Normal
Medidas ACPR: OFF CH SPC: 0 CH BW: 600MHz % de OCBW: 0 N dB: OFF
OCBW: OFF Adj CH Offs1: 600MHz Adj CH Offs2: 1200MHz Adj CH BW1&2:600MHz Oscilaciones de Fase: OFF
Línea Límite Límite A y B: OFF Pasa-No Pasa: OFF BW RBW: Auto
Tiempo de Barrido: Auto VBW: Auto Promedio: OFF
Disparo Retraso de disparo: 50ms Modo de disparo: Normal
Frecuencia de disparo: 1.5GHz
Pantalla Intensidad de LCD: 5 Ventana Dividida Inferior: OFF
Línea de Pantalla: OFF Ventana Dividida Superior: OFF
Archivo Copiar Tipo: Trazo Int. Renombrar Tipo: Trazo Ext.
Eliminar Tipo: Trazo Int.
Sistema GPIB: 2 Señal Auxiliar: OFF
Config. del Sistema: OFF Idioma: Inglés
Opciones Frecuencia de Referencia
Externa: 10MHz
Corr Norm TG: OFF Demodulador AM: OFF
Salida de TG: OFF
Valor de Referencia de TG: 0dBm Demodulador FM : OFF
Secuencia Secuencia: 1 Modo de Ejecución: Único
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 124 02/2007
6.3.14 SISTEMA (System)
La tecla System configura y muestra en pantalla los ajustes de sistema, incluyendo el resultado del Autotest, ajustes de fecha/hora y sincronización con otros dispositivos. El ajuste de sistema se puede guardar en un archivo y recuperar más tarde, incluso en otro equipo.
6.3.14.1 Guardar/Recuperar Ajustes del Sistema
1.- Pulse la tecla System. System
2.- Pulse F1 (Save/Recall Setup). Save/Recall
Setup.. F 1
3.- Pulse F1 o F2 repetidamente para seleccionar el archivo de sistema.
Setup1 2 3 4 5 F 1
Setup6 7 8 9 10 F 2
Pasos a realizar
4.- Pulse F3 (Save Now) o F4 (Recall Now) para guardar o recuperar el archivo con ajustes del sistema.
Save Now F 3
Recall Now F 4
Contenido de archivo
El archivo de sistema contiene la siguiente información. - Nivel de amplitud de referencia - Unidad de amplitud, escala - Frecuencias inicial/final - Frecuencia central y frecuencia de Span - VBW, RBW y Tiempo de barrido - Nivel de Generador de Seguimiento - Datos de normalización del Generador de Seguimiento
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 125
• Guardar/Copiar/Eliminar/Renombrar archivo de sistema Información general
Los archivos de sistema se pueden guardar, copiar, eliminar o renombrar utilizando las herramientas de archivo. Pulse la tecla File para tener acceso a cada función.
File
Copiar Pulse F1 (Copy). Copy... F 1
Eliminar Pulse F2 (Delete). Delete... F 2
Renombrar Pulse F3 (Rename). Rename... F 3
6.3.14.2 Configurar Interfaz de Comunicación Información general
El interfaz de comunicación se usa en las siguientes ocasiones. La configuración del interfaz se detalla en el capítulo correspondiente.
Software de ordenador: USB (esclavo), RS-232C Mando a distancia: USB (esclavo), RS-232C, GPIB
(opcional) Tipo de interfaz USB (esclavo): USB 1.1 o 2.0, Conector hembra Tipo B,
mini. Se usa en conexión con ordenador para control remoto.
RS-232C: Conector hembra, D-sub 9 pins. Se usa en conexión con ordenador para control remoto.
GPIB (opcional): Conector hembra de 24 pins. Se usa para control remoto.
Configuración de puerto USB (esclavo)
No se necesita ninguna configuración del sistema: solo conecte un cable USB al panel trasero. Conector hembra Tipo B, mini, USB1.1/2.0
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 126 02/2007
1.- La configuración de RS-232C se puede comprobar desde el menú del sistema. Pulse la tecla System.
System
2.- Pulse F3 (Serial Port). Serial Port.. F 3
3.- La configuración del puerto RS-232C aparece. Configure el ordenador según este ajuste. Baud: 115200 Parity: Ninguno Stop: 1 Data: 8
Stop1 F 3
Baud115200 F 1
ParityNone F 2
Data8 F 4
Configuración de RS-232C
4.- Conecte el cable RS-232C al terminal del panel trasero. (9 pins, hembra)
El interfaz GPIB es un elemento opcional preinstalado. Póngase en contacto con el personal de mantenimiento para una nueva instalación. 1.- Pulse la tecla System.
System
2.- Pulse F2 (GPIB Add). GPIB Add8 F 2
3.- Seleccione la dirección de GPIB usando las teclas Direccionales o el Selector rotativo. Configure el ordenador personal según este ajuste.
Configuración de GPIB (opcional)
4.- Conecte el cable GPIB al terminal del panel trasero.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 127
1.- Para comprobar el estado de instalación del GPIB, pulse la tecla System.
System
2.- Pulse F6 (More). More... F 6
3.- Pulse F4 (System Config On). System ConfigOn Off F 4
Comprobar estado de instalación del GPIB
4.- La ventana de configuración de sistema aparece. Cuando el módulo GPIB está instalado correctamente, la casilla de verificación está marcada.
Instalado
No instalado
1.- Para comprobar el resultado de la funcionalidad del GPIB interno, pulse la tecla System.
System
2.- Pulse F6 (More). More... F 6
3.- Pulse F2 (Self Test). Self Test... F 2
Comprobar el resultado del Autotest del GPIB
4.- El resultado de GPIB aparece en F1. Si el resultado es Fail (fallido), póngase en contacto con el personal de mantenimiento.
GPIBPass Fail F 1
Restricciones del GPIB
Siga estas reglas al usar el interfaz de GPIB.
- Pueden conectarse como máximo 15 dispositivos utilizando un
cable con 20 m de longitud, 2 m entre cada dos dispositivo en la
línea.
- Dirección única adjudicada para cada dispositivo.
- Al menos 2/3 de los dispositivos GPIB deben estar activados - No se permite ningún lazo o estructura paralela
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 128 02/2007
6.3.14.3 Visualizar Información de Sistema
• Visualizar error de sistema
Observe el área de mensajes de error en la parte inferior de la pantalla. Si hay un error de sistema, el mensaje aparece en color rojo.
Center : 1.5GHz (EXT Unlock)EXTUnlock
A continuación se detalla la lista de errores.
Pasos a realizar
EXTUnlock
RefUnlock
LO1Unlock
LO3Unlock
La entrada de referencia externa no funciona correctamente. La señal de referencia interna no funciona correctamente. El oscilador local 1 no funciona correctamente. El oscilador local 3 no funciona correctamente.
• Visualizar configuración de sistema
1.- Para comprobar la configuración del sistema, pulse la tecla System. System
2.- Pulse F6 (More).
More... F 6
3.- Pulse F4 (System Config On). System ConfigOn Off F 4
Pasos a realizar
4.- La ventana de configuración de sistema aparece, mostrando cuatro tipos de información (de arriba hacia abajo).
- Número de serie
- Versión de software y hardware
- Instalación de artículos opcionales
- Selección de señal de referencia
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 129
Número de serie Versión de software y hardware
Instalación de
artículos opcionales Selección de
señal de referencia
5.- Para cerrar la ventana de configuración, pulse F4 de nuevo (System Config Off).
System ConfigOn Off F 4
Versión de software/hardware
Muestra las versiones con su respectiva fecha de publicación para el hardware, software y firmware instalados en el equipo. Se utilizan para varias operaciones de servicio.
Muestra qué artículos opcionales están instalados actualmente.
: instalado : no instalado.
Estado de instalación de artículos opcionales Etiqueta Descripción
Pack de batería / módulo de alimentación de
DC
Interfaz GPIB
Demodulador
Módulo de señal de referencia interna con
estabilidad de media de ±1ppm .
300Hz RBW
9k/120kHz RBW incluido en el Filtro EMI
10k/100kHz RBW Estado de señal de referencia
La casilla marcada muestra la señal de referencia utilizada.
: habilitado, : deshabilitado.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 130 02/2007
Mensaje Descripción
Señal de referencia interna, estabilidad
estándar
Señal de referencia interna, estabilidad media.
Disponible cuando el módulo de estabilidad
±1ppm está instalado.
Señal de referencia interna, estabilidad alta
(reservada).
Señal de referencia externa. 6.3.14.4 Visualizar el resultado del Autotest
El equipo realiza una serie de pruebas internas cada vez que se enciende.
El equipo realiza una serie de pruebas internas cada vez que se enciende. Si cualquiera de las pruebas falla, póngase en contacto con el personal de mantenimiento.
1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
3.- Pulse F2 (Self Test). Self Test... F 2
4.- El resultado aparece en F1 ~ F4. (El resultado de GPIB aparece sólo si el módulo está instalado)
GPIBPass Fail F 1
FlashPass Fail F 2
SDRAMPass Fail F 3
RTCPass Fail F 4
Información general
5.- Pulse F6 (Return) para volver al menú anterior. Return F 6
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 131
Artículo GPIB: Conexión opcional de interfaz GPIB. Disponible
sólo cuando el módulo GPIB está instalado Flash Memoria interna para almacenar programas y
datos del sistema. SDRAM Memoria interna SDRAM en la cual se ejecutan los
programas. RTC Reloj de tiempo real que controla la fecha y la hora
. 6.3.14.5 Ajustar Fecha/Hora
1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
3.- Pulse F1 (System Clock). SystemClock... F 1
1. Activar reloj en pantalla
4.- Pulse F3 (Clock On). El reloj aparece en
la esquina inferior derecha de la pantalla.
ClockOn Off F 3
5.- Pulse F1 (Date). Date... F 1
6.- Pulse F1 (Year) ~ F4 (Day of Week). Introduzca el valor utilizando las teclas numéricas. Pulse la tecla Enter para confirmar el valor.
µ
La pantalla del reloj cambia en consecuencia.
Year F 1
Month F 2
Day F 3
Day of Week F 4
2. Ajustar la fecha
Año: 2000 ~ 2064
Mes 1 ~ 12 (corresponde a los meses de Enero ~
Diciembre)
Día: 1 ~ 31
Día de Semana: 1 ~ 7 (corresponde a los días de Domingo ~
Sábado)
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 132 02/2007
7.- Pulse F1 (Date). Date... F 13. Ajustar la hora
8.- Pulse el F1 (Hour) ~ F3 (Second).
Introduzca el valor utilizando las teclas
numéricas. Pulse la tecla Enter para
confirmar el valor.
µ
La pantalla de reloj cambia en consecuencia.
Hora 0 ~ 23
Minuto 0 ~ 59
Segundo 0 ~ 59
Hour F 1
Minute F 2
Second F 3
6.3.14.6 Sincronizar el AE-966/967 con otro Equipo
Utilizando la entrada/salida de frecuencia de referencia del panel trasero, AE-
966/967 puede sincronizar su frecuencia interna con otro dispositivo. El AE-966/967
puede funcionar en modo dominante (master), que emite señal de referencia a otro
dispositivo, o esclavo (slave), que recibe señal de referencia de otro dispositivo.
6.3.14.7 AE-966/967 funcionando en modo master (señal de
referencia interna) Pasos a realizar Conecte el terminal de salida de señal de
referencia del panel trasero a la entrada de
referencia del otro dispositivo.
Tipo de señal Nivel de salida: 10MHz, señal de 5V TTL (asumiendo que la
impedancia de carga es infinita)
Impedancia de salida: 50 Ω
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 133
1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
3.- Pulse F4 (System Config On). System ConfigOn Off F 4
La ventana de configuración de sistema aparece. El mensaje
de la Señal de Referencia Interna muestra el
estado.
: habilitado, : deshabilitado.
Señal de referencia interna, estabilidad estándar
Señal de referencia interna, estabilidad mediana.
Disponible cuando el módulo de estabilidad ±1ppm está
instalado. El icono MED aparece en la parte inferior de la
pantalla.
Control de estabilidad
Señal de referencia interna, estabilidad alta (reservada). 6.3.14.8 AE-966/967 funcionando en modo esclavo (señal de
referencia externa).
1.- Pulse la tecla Option. Option
2.- Pulse F4 (Ext Ref Freq) para permitir la
señal de referencia externa.
Ext Ref Freq10MHz F 4
3.- Utilice las teclas Direccionales para
seleccionar la frecuencia de referencia
externa.
4.- Conecte la señal de referencia externa al
terminal de entrada del panel trasero.
Pasos a realizar
5.- El icono de señal de referencia externa
aparece en la parte inferior de la pantalla.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 134 02/2007
Frecuencia Hay 10 tipos disponibles (unidades en MHz).
1.0 1.544 2.048 5.0 10.0
10.24 13.0 15.36 15.4 19.2 1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
3.- Pulse F4 (System Config On). System ConfigOn Off F 4
Control de estado
La ventana de configuración de sistema aparece. El mensaje
de la Señal de Referencia Externa muestra el
estado.
: habilitado, : deshabilitado. 6.3.14.9 Menú de Servicio
Las siguientes funciones están dirigidas sólo a personal de mantenimiento.
1.- Pulse la tecla System. System
2.- Pulse F5 (Service). Service... F 5
Mantenimiento
de elementos
opcionales
3.- Para poder continuar, debe introducir la
contraseña en la ventana de comandos.
PASSWORD:
1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
Diagnóstico de RF
3.- Pulse F3 (RF Diagno) para ver el
resultado del diagnóstico de RF. RF Diagno... F 3
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 135
6.3.15 SECUENCIA (Seq)
La función de secuencia graba y ejecuta macros definidos por el usuario (pasos de medida). Hay 10 secuencias disponibles en modo de repetición o ejecución individual, cada una con 20 pasos disponibles para todas las operaciones del sistema. Las características de pausa y retraso permiten observar el resultado de la medida durante la secuencia.
6.3.15.1 Editar Secuencia
1.- Pulse la tecla Seq. Seq
1. Seleccionar la secuencia
2.- Pulse F1 (Select Seq 1 ~ 5) o F2 (Select
Seq 6 ~ 10) repetidamente para seleccionar
el número de secuencia deseado.
Select Seq1 2 3 4 5 F 1
Select Seq6 7 8 9 10 F 2
1.- Pulse F3 (Edit). Edit... F 3
2.- Pulse F1 (Start Edit). Start Edit F 1
2. Empezar a editar
3.- El círculo ante el título Start Edit en la
zona central de la pantalla se pone verde. Start Edit
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 136 02/2007
Hay 20 pasos disponibles para cada secuencia. Cada operación
clave puede ser registrada como un paso.
Pulse la tecla Enter cada vez para confirmar la introducción de un
paso. (En algunos casos esto no es necesario: compruebe si el
paso aparece en la ventana).
Ejemplo: Activar el sistema señal auxiliar
1.- Pulse la tecla System.
2.- Pulse F4 (Aux Sig On).
3.- Prensa la tecla Enter.
System
Aux SigOn Off F 4
Ejemplo: Ejecutar Autoset
1.- Pulse la tecla de Autoset.
2.- Pulse F1 (Autoset).
3.- Pulse la tecla Enter.
Autoset
Autoset F 1
2a. Añadir un paso.
El resultado de la operación aparece así: Aux Sig OnAutoset
La función de retraso introduce un período de espera entre los
pasos.
1.- Pulse F2 (Delay ms) Delay ms100 X F 2
2.- Introduzca el tiempo de retraso (paso de
100ms) utilizando las teclas numéricas. Por
ejemplo, pulsando 5 veces introducimos un
paso de 500ms (5 * 100ms).
µ
2b. Añadir retraso
3.- Introduzca el tiempo de retraso (paso de 100ms) utilizando las
teclas numéricas. Por ejemplo, pulsando 5 veces introducimos un
paso de 500ms (5 * 100ms).
Rango: 1 ~ 100, resolución de 100ms
2c. Pausar la secuencia
La ejecución de la secuencia se interrumpe, hasta que el usuario
pulsa F1 (Continue). Útil para observar el resultado de una prueba
particular (por ejemplo medida de ACPR).
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 137
1.- Pulse F3 (Wait to go). Wait to go F 3
2.- Cuando la secuencia se ejecuta, F1
(Continue) aparece en el menú. Continue F 1
Introduce una secuencia entera.
1.- Pulse F4 (Do Seq). Do Seq... F 4
2.- Pulse F1 (Select Seq 1 ~ 5) o F2 (Select
Seq 6 ~ 10) repetidamente para seleccionar
la secuencia a introducir.
Select Seq1 2 3 4 5 F 1
Select Seq6 7 8 9 10 F 2
2d. Introducir otra secuencia
Nota No se puede introducir la secuencia que se edita en este
momento.
1.- Pulse F6 (More). More F 6
2.- Utilice las teclas Arriba/Abajo para
desplazar el cursor al punto de introducción.
3.- Pulse F1 (Insert). Se creará un nuevo
espacio en blanco.
Insert F 1
Aux Sig OnAutosetDelay ms 5sNdB BW OnNdB 5
Aux Sig OnAutosetDelay ms 5s
NdB BW OnNdB 5
2e. Introducir un espacio en blanco
4.- Pulse F6 (Return) para volver al menú
anterior. Return F 6
1.- Pulse F6 (More). More F 6
2.- Utilice las teclas Arriba/Abajo para
desplazar el cursor al punto de eliminación.
2f. Eliminar un paso
3.- Pulse F3 (Delete). El paso será
eliminado. Delete F 3
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 138 02/2007
Aux Sig OnAutosetDelay ms 5sNdB BW OnNdB 5
Aux Sig OnDelay ms 5sNdB BW OnNdB 5
4.- Para deshacer la eliminación, pulse F5
(Undelete). Undelete F 5
5.- Para volver al menú anterior, pulse F6
(Return). Return F 6
1.- Pulse F6 (More). More F 6
2.- Pulse F4 (Delete All). Delete All.. F 4
3.- Pulse F2 (Yes) para confirmar o F1 (No)
para anular. Todos los pasos serán
eliminados.
No F 1
Yes F 2
Aux Sig OnAutosetDelay ms 5sNdB BW OnNdB 5
4.- Para deshacer la eliminación, pulse F5
(Undelete). Undelete F 5
2g. Eliminar todos los pasos en una secuencia
5.- Pulse F6 (Return) para volver al menú
anterior. Return F 6
1.- Pulse F5 (Stop Edit). Stop Edit F 53. Dejar de editar
2.- El círculo ante el título Start Edit en la
zona central de la pantalla se pone gris. Start Edit
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 139
1.- Pulse F6 (More). More F 6
2.- Pulse F2 (Save). La secuencia será
guardada. Save F 2
4. Guardar la secuencia editada
3.- Pulse F6 (Return) para volver al menú
anterior. Return F 6
6.3.15.2 Eliminar todas las secuencias
1.- Pulse la tecla Seq. Seq
2.- Pulse F5 (Delete Seq All). DeleteSeq All... F 5
3.- Pulse F2 (Yes) para confirmar, o F1 (No)
para anular. Las 10 secuencias serán
eliminadas.
No F 1
Yes F 2
4.- Para volver al menú anterior, pulse F6
(Return). Return F 6
Pasos a realizar
Nota La acción Delete Seq All es irreversible — la función Undelete
no se puede utilizar. 6.3.15.3 Ejecutar Secuencia
Esta sección asume que la secuencia ya está editada.
1.- Pulse la tecla Seq. Seq
1. Seleccionar la secuencia
2.- Pulse F1 (Select Seq 1 ~ 5) o F2 (Select
Seq 6 ~ 10) repetidamente para seleccionar
la secuencia.
Select Seq1 2 3 4 5 F 1
Select Seq6 7 8 9 10 F 2
3.- Pulse F4 (Run). Run... F 4
2. Seleccionar el modo de ejecución
4.- Pulse F1 (Run Mode) para seleccionar el
modo de ejecución, repetido (Rept) o único
(Sngl).
Run ModeRept Sngl F 1
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 140 02/2007
Repetido: Repite la secuencia hasta que se pulse la tecla F6
(Stop).
Nota: F6 (Stop) aparece sólo mientras se ejecuta la secuencia.
Único: Ejecuta la secuencia una sola vez.
5.- Pulse F2 (Run Now). Run Now F 2
6.- El icono de secuencia aparece en la parte
inferior de la pantalla.
3. Ejecutar secuencia
7.- Para interrumpir la ejecución, pulse F6
(Stop). En modo de ejecución única, la
secuencia se para automáticamente cuando
todos los pasos son completados.
Stop F 6
6.3.15.4 Guardar / Copiar / Eliminar / Renombrar archivos de
Secuencia Información general
Los archivos de secuencia pueden ser guardados, copiados, eliminados o renombrados utilizando las funciones de archivo. Pulse la tecla File para acceder a cada función.
File
Guardar/ Copiar
Pulse F1 (Copy). Copy... F 1
Eliminar Pulse F2 (Delete). Delete... F 2
Renombrar Pulse F3 (Rename). Rename... F 3
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 141
6.3.16 GENERADOR DE TRACKING
El Generador de Tracking (Seguimiento) genera una señal de barrido con tiempo de barrido y rango de frecuencia que coinciden con el equipo. La amplitud se mantiene a un valor constante sobre el rango de frecuencia total, lo cual es muy útil para probar la respuesta de frecuencia del Dispositivo Bajo Prueba.
6.3.16.1 Activar el Generador de Tracking (TG)
1.- Pulse la tecla Option. Option
2.- Pulse F1 (TG). TG... F 1
3.- Pulse F1 (TG On). TGOn Off
F 1
1. Activar salida del TG
4.- La salida del generador de seguimiento
se activa.
Ω
±
5.- Pulse F2 (TG Level). TG Level F 2
2. Ajustar el nivel de salida del TG
6.- Ajuste el nivel de salida del TG utilizando
las teclas Direccionales y el Selector rotativo.
Rango: 0 ~ -50dBm
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 142 02/2007
6.3.16.2 Normalizar el generador de seguimiento
1.- Pulse la tecla Option. Option
2.- Pulse F1 (TG). TG... F 1
3.- Pulse F5 (Ref Value). Ref Value F 5
4.- Ajuste el valor de referencia utilizando las
teclas Direccionales y el Selector rotativo.
1. Ajustar nivel de referencia
El nivel de normalización se ajusta al valor de referencia, sin tener
en cuenta el nivel de salida del TG.
Rango: - 130 ~ +20dBm
5.- Pulse F3 (Execute Normalization). ExecuteNormalization..
F 3
6.- Pulse F2 (Yes) para confirmar, o F1 (No)
para anular. La normalización se ejecuta. No F 1
Yes F 2
2. Ejecutar normalización
7.- Pulse F6 (Return) para volver al menú
anterior. Return F 6
8.- Para permitir la normalización, pulse F4
(Norm Corr On).
Norm CorrOn Off F 4
3. Activar la normalización
9.- La normalización se activa y aparece el
icono TG. 6.3.16.3 Comprobar estado de instalación del TG
1.- Pulse la tecla System. System
1.- Ejecutar normalización
2.- Pulse F6 (More). More... F 6
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 143
3.- Pulse F4 (System Config On). La
configuración aparece en pantalla. System Config
On Off F
4.- El signo TG muestra el estado de
instalación, instalado (marcado) o no
instalado (no marcado).
Instalado
No instalado
6.3.17 DEMODULADOR (OPCIONAL)
El demodulador opcional FM/AM recupera señales AM o FM moduladas de banda base. La señal demodulada puede ser extraída de la salida de audio del panel trasero.
6.3.17.1 Activar Demodulación
1.- Pulse la tecla Option. Option
2.- Pulse F2 (Demod) Demod... F 2
Pasos a realizar
3.- Seleccione AM o FM pulsando F1 (FM
On) o F2 (AM On).
FMOn Off F 1
AMOn Off F 2
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 144 02/2007
6.3.17.2 Activar la salida de audio
1.- Pulse F2 (Demod). Demod... F 2
2.- Pulse F3 (SPK On). SPKOn Off F 3
Pasos a realizar
3.- La salida de audio del panel trasero se activa.
3.5 mm, mono (jack estéreo).
Nota: Hay que activar AM o FM antes de SPK On. 6.3.17.3 Ajustar el volumen de la salida de audio
1.- Pulse F2 (Demod). Demod... F 2
2.- Pulse F4 (Volume). Volume F 4
3.- El nivel de volumen aparece en la ventana de
comandos.
VOLUME: 30
Pasos a realizar
4.- Ajuste el volumen de salida utilizando las
teclas Numéricas, las teclas Direccionales o el
Selector rotativo.
µ
Nivel de volumen
0 ~ 63
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 145
6.3.17.4 Eliminar ruido de la salida de audio (Squelch)
1.- Pulse F2 (Demod). Demod... F 2
2.- Pulse F5 (Squelch). Squelch F 5
3.- El nivel de Squelch aparece en la ventana de
comandos. El nivel de salida inferior al ajustado
es silenciado.
SQUELCH
Pasos a realizar
Ajuste el nivel de Squelch utilizando las teclas
Numéricas, las teclas Direccionales o el Selector
rotativo.
µ
Chapotee nivel
0 ~ 4
6.3.17.5 Comprobar estado de instalación del demodulador
1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
3.- Pulse F4 (System Config On). La
configuración aparece en pantalla.
System ConfigOn Off F 4
Pasos a realizar
4.- El signo Demod muestra el estado de
instalación, instalado (marcado) o no instalado
(no marcado).
Instalado
No instalado
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 146 02/2007
6.3.18 FILTRO EMI (Opcional)
El filtro EMI opcional se utiliza en situaciones de medida específicas como la detección de promedio EMI, donde se necesita un nivel de sensibilidad más alto que la configuración estándar. Cuando este módulo está instalado, el equipo consigue características adicionales: modo de detección Promedio (AVG)/Cuasi pico (QPeak) y 9k/120k RBW. Para una nueva instalación, póngase en contacto con el centro de mantenimiento. 6.3.18.1 Seleccionar modo de detección de señal AVG/QPeak
3. Pulse la tecla Trace. Trace
4. Pulse F6 (More). More F 6
5. Pulse el F3 (Detection). Detection.. F 3
Pasos a realizar
6.- El modo de detección de señal aparece.
Cuando el filtro EMI está instalado, F4 (AVG) y
F5 (QPeak) están disponibles.
Normal F 1
Sample F 2
Peak+ F 3
AVG F 4
QPeak F 5
Parámetro AVG (promedio): Detecta el nivel de potencia promedio de las
muestras utilizando un filtro paso bajo. Útil para suavizar el nivel del
ruido.
QPeak (quasi pico): Detecta el nivel de potencia del cuasi pico de las
muestras. Útil para ver en Span cero sin perder variaciones de la señal.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 147
6.3.18.2 Seleccionar 9kHz/120kHz RBW
1.- Pulse la tecla BW. BW
2.- Pulse F1 (RBW Manu). RBWAuto Manu F 1
Pasos a realizar
3.- Seleccione 9kHz/120kHz RBW utilizando el
Selector rotativo. El valor de RBW aparece en la
ventana de comandos.
RBW: 9kHz Nota En el modo automático, RBW se selecciona según el ajuste de
referencia interno. 6.3.18.3 Comprobar estado de instalación del filtro EMI
1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
3.- Pulse F4 (System Config On). La ventana de
configuración de sistema aparece en pantalla.
System ConfigOn Off F 4
Pasos a realizar
4.- El signo de RBW 9/120k muestra el estado de
instalación, instalado (marcado) o no instalado
(no marcado).
Instalado
No instalado
Nota Las variantes del filtro EMI (9k/120k RBW) y (10k/100k RBW) son
exclusivas. Ambas no pueden ser instaladas juntas.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 148 02/2007
6.3.19 SOFTWARE DE ORDENADOR
El software de ordenador para operación remota se incluye en el CD suministrado con el equipo. El programa monitoriza la forma de onda y permite realizar operaciones con el equipo a través del ordenador.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 149
6.3.19.1 Instalar el Software
• Requisitos del ordenador Software Sistema operativo: Windows 2000/XP Hardware USB: 1 conector USB del tipo 1.1 o 2.0
6.3.19.2 Proceso de instalación 1. Lanzar la instalación
1. Descomprima el fichero ZIP.
2. Haga doble clic en Setup.exe.
3. La pantalla de instalación se abre. Cierre todas otras aplicaciones y elija OK. Si necesita interrumpir la instalación, pulse la tecla Exit Setup.
4. Si desea instalar en un directorio específico, pulse el botón de Cambio de Directorio (Change Directory).
2. Iniciar la instalación
5. Pulse el icono para comenzar instalación.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 150 02/2007
6.- Cuando el mensaje de “instalación finalizada con éxito” aparece en la pantalla, pulse OK.
6.3.19.3 Ajustar el Software de Conexión
Esta sección asume que el software ya está instalado.
• Configurar el interfaz
Están disponibles el conector USB o el RS-232C.
Configurar el USB
No hay necesidad de configurar nada en el
equipo. Simplemente conecte el cable USB al
panel trasero.
Conector hembra tipo B mini.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 151
1.- La configuración del RS-232C puede ser
comprobada en el menú de sistema. Pulse la
tecla System.
System
2.- Pulse F3 (Serial Port). Serial Port.. F 3
3.- Aparecerá la configuración del puerto RS-
232C. Configure el ordenador personal según
estos ajustes.
Baud: 115200
Parity: None
Stop: 1
Data: 8
Stop1 F 3
Baud115200 F 1
ParityNone F 2
Data8 F 4
Configurar el RS-232C
4.- Conecte el cable RS-232C al terminal del
panel trasero.
9 pins, hembra
6.3.19.4 Ejecutar el software Pasos a seguir
1.- Elegir el software del menú de inicio.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 152 02/2007
2.- El software se abre.
3.- Pulse el icono de Configuración.
Aparecerá una ventana con los parámetros
de configuración.
4.- Seleccione el puerto de conexión (puerto serie COM)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 153
5.- Seleccione el puerto de conexión (puerto serie COM)
Selección del puerto: Seleccione el puerto especificado en la configuración del ordenador. Para comprobar la configuración en el ordenador personal, vaya a Panel de control → Sistema → Hardware → Administrador de Dispositivos.
6.- Pulse de nuevo el icono de Configuración
para cerrar la ventana.
7.- Pulse el icono de Puerto COM Abierto. La
conexión se establece cuando los otros
iconos se activan.
1.- Pulse el icono de Captura. Asegúrese de
que la forma de onda mostrada en la pantalla
del equipo es capturada correctamente.
Control de funcionalidad
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 154 02/2007
6.3.19.5 Utilizar el Software
• Establecer la conexión
1.- Pulse el icono de Ajustes y abra ventana
de configuración de parámetros.
2.- Seleccione el puerto serie deseado.
3.- Pulse el icono de puerto COM. La
conexión se establece cuando los otros
iconos se activan.
Pasos a seguir
Ajustes del puerto: Seleccione el puerto especificado en la
configuración del ordenador. Para comprobar la configuración en el
ordenador personal, vaya a Panel de control → Sistema →
Hardware → Administrador de Dispositivos.
• Capturar forma de onda Pasos a seguir
1.- Pulse el icono de Capturar. La forma de
onda actual será capturada y aparece en la
pantalla.
Pantalla
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 155
• Eliminar forma de onda Pasos a seguir
1.- Pulse el icono de Eliminar trazo. La forma
de onda será eliminada de la pantalla.
Pantalla
• Guardar forma de onda
1.- el icono de Ajustes. Seleccione el formato
de archivo de *.jpg/*.bmp (foto de pantalla),
*.txt (datos de medida).
Pasos a seguir
2.- Pulse el icono de Guardar. La ventana de
diálogo estándar de Windows de “Guardar
archivo” se abre. Seleccione el directorio y
guarde el archivo.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 156 02/2007
Formato de archivo
El archivo *.txt contiene la siguiente información:
- Frecuencia (MHz) y Amplitud para todas las formas de onda
- Nivel de referencia de amplitud, unidad y escala
- Frecuencia Inicial y Final, Frecuencia Central, y
Frecuencia de Span
- RBW, VBW y Tiempo de barrido
- Fecha y hora (si ya está configurada)
• Imprimir imagen de pantalla Pasos a seguir
1.- Pulse el icono de Impresora. La ventana
de diálogo estándar de Windows “Imprimir
archivo” se abre. Seleccione la impresora e
imprima la imagen de pantalla.
Nota El contraste de la imagen de pantalla será invertido (el color del
fondo de la pantalla se hace blanco).
• Utilizar marcadores
1.- Pulse el icono de Marcador. La ventana
con funciones del Marcador aparece en
pantalla.
Pasos a seguir
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 157
2.- Seleccione Live o Storage.
3.- Compruebe la casilla del
Marcador correspondiente. Hay 5
marcadores disponibles: 0 ~ 4.
4.- Introduzca la frecuencia de cada
Marcador.
5.- Seleccione el tipo de Marcador
normal (N) o delta (1). Ejemplo:
Marcador 0 y Delta 1: el Marcador de
Delta muestra la diferencia entre
Marcador 0 y Marcador 1.
6.- La pantalla es actualizada con marcadores en color rojo y valores
de marcador puestos en una lista en la parte inferior de la pantalla.
• Salir del Programa Pasos a seguir Pulse el icono de Salida o pulse a la vez las
teclas Alt + F4.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 158 02/2007
6.3.20 COMUNICACIÓN REMOTA
El equipo permite ser controlado remotamente mediante la interfície IEEE 488.2 y SCPI estándar. Los comandos cubren la mayor parte de las operaciones con el equipo. Hay tres interfaces disponibles: USB (esclavo), RS-232 y GPIB (opcional).
6.3.20.1 Configurar el Interfaz Tipo de interfaz USB (esclavo): USB 1.1 o 2.0, Conector hembra Tipo B, mini.
RS-232C: Conector hembra, D-sub 9 pins. GPIB (opcional): Conector hembra de 24 pins.
Configuración de puerto USB (esclavo)
No se necesita ninguna configuración del sistema: sólo conecte un cable USB al panel trasero. Conector hembra Tipo B, mini, USB1.1/2.0
El icono USB aparece en pantalla cuando se detecta una conexión.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 159
1.- La configuración de RS-232C se puede comprobar desde el menú del sistema. Pulse la tecla System.
System
2.- Pulse F3 (Serial Port). Serial Port.. F 3
3.- La configuración del puerto RS-232C aparece. Configure el ordenador según este ajuste. Baud: 115200 Parity: Ninguno Stop: 1 Data: 8
Stop1 F 3
Baud115200 F 1
ParityNone F 2
Data8 F 4
Configuración de RS-232C
4.- Conecte el cable RS-232C al terminal del panel trasero. (9 pins, hembra)
El interfaz GPIB es un elemento opcional preinstalado. Póngase en contacto con el personal de mantenimiento para una nueva instalación. 1.- Pulse la tecla System.
System
2.- Pulse F2 (GPIB Add). GPIB Add8 F 2
3.- Seleccione la dirección de GPIB usando las teclas Direccionales o el Selector rotativo. Configure el ordenador personal según este ajuste.
Configuración de GPIB (opcional)
Conecte el cable GPIB al terminal del panel trasero.
1.- Para comprobar el estado de instalación del GPIB, pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
3.- Pulse F4 (System Config). System ConfigOn Off F 4
Comprobar estado de instalación del GPIB
4.- La ventana de configuración de sistema aparece. Cuando el módulo GPIB está instalado correctamente, la casilla de verificación está marcada.
Instalado
No instalado
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 160 02/2007
1.- Para comprobar el resultado de la funcionalidad del GPIB interno, pulse la tecla System.
System
2.- Pulse F6 (More). More... F 6
3.- Pulse F2 (Self Test). Self Test... F 2
Comprobar el resultado del Autotest del GPIB
4.- El resultado de GPIB aparece en F1. Si el resultado es Fail (fallido), póngase en contacto con el personal de mantenimiento.
GPIBPass Fail F 1
Restricciones del GPIB
Siga estas reglas al usar el interfaz de GPIB.
- Pueden conectarse como máximo 15 dispositivos utilizando un
cable con 20 m de longitud, 2 m entre cada dos dispositivo en la
línea.
- Dirección única adjudicada para cada dispositivo.
- Al menos 2/3 de los dispositivos GPIB deben estar activados - No se permite ningún lazo o estructura paralela
Control de Funcionalidad
Ejecute este comando del terminal. *idn? Este comando debería devolver como resultado el Fabricante, el Número de Modelo, el Número de serie, y la Versión del firmware.
PROMAX, AE-967, P920130, V3.01
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 161
7 SINTAXIS DE LOS COMANDOS
Los comandos son parcialmente compatibles con IEEE488.2 (1992) y SCPI (1994) estándar. Los comandos no son sensibles a mayúsculas y minúsculas. Ejemplo de comando meas:freq:cen _ 9 _ khz
1 2 3 4 5 1: Comando 2: Espacio 3: Parámetro 1 4: Espacio 5: Parámetro 2
Comando Varios comandos pueden ser conectados para formar un comando
complejo. El siguiente ejemplo puede ser separado en: meas: (root node) + freq: + cen:
Ejemplo de parámetro
0/1 0 o 1. 1~4 Número entero entre 1, 2, 3 y 4. 0.01~5 Número decimal entre 0.01 y 5. KHz Unidad (no sensible a mayúsculas y
minúsculas) Mensaje de final Marca el final de una línea de comando. Cualquiera de los
siguientes es aceptable. CR^END: Código “Line feed” (hexadecimal 0D) junto con
el mensaje END. CR Código “Line feed”. <dab> ^END Último byte de datos junto con el mensaje END.
Separador de mensaje
; (punto y coma) Separador de comandos.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 162 02/2007
7.1 COMANDOS
Los comandos no son sensibles a mayúsculas y minúsculas. Guión bajo significa un espacio (100_mhz→100 mhz).
• Frecuencia
Comando Descripción
meas:freq:cen? Devuelve la frecuencia central en kHz.
Ejemplo: 1000000 khz
meas:freq:cen Ajusta la frecuencia central.
Ejemplo: meas:freq:cen_100_mhz
meas:freq:st? Devuelve la frecuencia inicial en kHz.
Ejemplo: 1000000 khz
meas:freq:st Ajusta la frecuencia inicial.
Ejemplo: meas:freq:st_100_mhz
meas:freq:stp? Devuelve la frecuencia final en kHz.
Ejemplo: 1000000 khz
meas:freq:stp Ajusta la frecuencia final.
Ejemplo: meas:freq:stp_100_mhz
meas:freq:ss? Devuelve el paso de frecuencia en kHz.
Ejemplo: 1000000 khz
meas:freq:ss Ajusta el paso de frecuencia.
Ejemplo: meas:freq:ss_100_mhz
meas:freq:cen:fw Desplaza la frecuencia central un paso hacia delante.
meas:freq:cen:bw Desplaza la frecuencia central un paso hacia atrás.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 163
• Span
Comando Descripción
meas:span? Devuelve el Span de la frecuencia.
Ejemplo: 10000 kHz
meas:span Ajusta el Span de la frecuencia.
Ejemplo: meas:span:10_mhz
meas:span:full Ajusta el Span de la frecuencia a completo.
meas:span:zero Ajusta el Span de la frecuencia a cero.
meas:span:last Recupera el último ajuste de Span de frecuencia.
• Amplitud
Comando Descripción
meas:refl:unit? Devuelve la unidad de nivel de referencia.
Parámetro: 1 (dBm), 2 (dBmV), 3 (dBuV)
meas:refl:unit Ajusta la unidad de nivel de referencia.
Parámetro: 1 (dBm), 2 (dBmV), 3 (dBuV)
Ejemplo: meas:refl:unit:_1 (dBm)
meas:refl? Devuelve el nivel de referencia en la unidad actual.
Ejemplo: -30 (-30dBm cuando la unidad es dBm)
meas:refl Ajusta el nivel de referencia en la unidad actual.
Ejemplo: meas:refl:_-30 (-30dBm cuando la unidad es dBm)
meas:refl:scale? Devuelve la escala de la amplitud.
Parámetro: 1(10dB/Div), 2(5dB/Div), 3(2dB/Div), 4(1dB/Div)
meas:refl:scale Ajusta la escala de amplitud.
Parámetro: 1(10dB/Div), 2(5dB/Div), 3(2dB/Div), 4(1dB/Div)
Ejemplo: meas:refl:scale_1 (10dB/Div)
meas:refl:exg? Devuelve la ganancia/pérdida externa en dB.
Ejemplo: -6 (-6dB)
meas:refl:exg Ajusta la ganancia/pérdida externa en dB.
Ejemplo: meas:refl:exg _-6 (-6dB)
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 164 02/2007
Comando Descripción
meas:refl:corr:edit Ajusta los datos de corrección de amplitud (frecuencia,
amplitud). Es necesario especificar el índice de la tabla y el
número de corrección.
Ejemplo: meas:refl:corr:edit_1_CR_2,100,-40,150,-30
(tabla index1, 2 data, 100MHz /-40dB, 150MHz /-30dB)
meas:refl:corr:edit:del Elimina un punto de corrección de amplitud. Es necesario
especificar el grupo y el número del punto.
Ejemplo: meas:refl:corr:edit:del_5_30 (eliminar en grupo
5, punto 30)
meas:refl:corr:edit:dela
ll
Elimina todos los puntos del grupo de corrección de
amplitud. Es necesario especificar el número de grupo.
Ejemplo: meas:refl:corr:edit:delall_5 (eliminar grupo No.5)
meas:refl:corr:edit:quit Abandonar el modo de corrección de amplitud.
meas:refl:corr:no? Devuelve el número del grupo de corrección de amplitud
activado.
Parámetro: ninguno, 1 ~ 5 (grupo de corrección)
meas:refl:corr:on? Devuelve como resultado si el grupo de corrección de
amplitud está activo o inactivo. Es necesario especificar el
número de grupo.
Parámetro: On, Off
Ejemplo: meas:refl:corr:on_1? (¿Está activado el grupo
No1?)
meas:refl:corr:on Activa el grupo de corrección de amplitud. Es necesario
especificar el número de grupo.
Ejemplo: meas:refl:corr:on_1 (Activar grupo No 1)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 165
Comando Descripción
meas:refl:corr:off Desactiva el grupo de corrección de amplitud. Es necesario
especificar el número de grupo.
Ejemplo: meas:refl:corr:off_1 (Desactivar grupo No 1)
meas:inputz? Devuelve la impedancia de entrada.
Parámetro: 50, 75
meas:inputz Ajusta la impedancia de entrada.
Parámetro: 50, 75
Ejemplo: meas:inputz_50 (50 )
meas:inputz:cal? Devuelve el valor de calibración de la impedancia de
entrada en dB.
meas:inputz:cal Ajusta el valor de calibración de impedancia de entrada en
dB.
Ejemplo: meas:inputz:cal_5.9 (5.9dB)
• Autoajuste
Comando Descripción
meas:autoset:run Ejecutar el autoajuste.
meas:autoset:amp:
auto
Ajusta el nivel mínimo de amplitud de autoajuste en modo
automático.
meas:autoset:amp:
man
Ajusta el nivel mínimo de amplitud de autoajuste en modo
manual. Es necesario especificar la amplitud en dB.
Ejemplo: meas:autoset:amp:man_20 (20dB)
meas:autoset:amp:
mode?
Devuelve el modo de nivel mínimo de amplitud de
autoajuste.
Parámetro: auto, manual
meas:autoset:span:
auto
Ajusta el Span de frecuencia de autoajuste en modo
automático.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 166 02/2007
Comando Descripción
meas:autoset:span:
man
Ajusta el Span de frecuencia de autoajuste en modo
manual. Es necesario especificar la unidad.
Ejemplo: meas:autoset:span:man_100_khz (100 kHz)
meas:autoset:span:
mode?
Devuelve el modo del Span de frecuencia de autoajuste.
Parámetro: auto, manual
• Marcador y Búsqueda de picos
Comando Descripción
meas:mark:on? Devuelve marcador Activado/ Desactivado. Es necesario
especificar el número del Marcador.
Parámetro: On, Off
Ejemplo: meas:mark:on_1? (¿Está activado Marcador 1?)
meas:mark:on Activar el Marcador.
Parámetro: 1~5 (número del Marcador), todos (todos los
marcadores)
Ejemplo: meas:mark:on_1 (Activar Marcador 1)
meas:mark:off Desactivar el Marcador.
Parámetro: 1~5 (número del Marcador), todos (todos los
marcadores)
Ejemplo: meas:mark:off_1 (Desactivar Marcador 1)
meas:mark:norm Ajusta un Marcador a modo normal.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:norm_1 (Ajustar Marcador 1 a modo
normal)
meas:mark:norm:
freq?
Devuelve la frecuencia de un Marcador normal. Es necesario
especificar el número del Marcador.
Ejemplo: meas:norm:freq_1? (¿Frecuencia del Marcador 1
normal?)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 167
Comando Descripción
meas:mark:norm:
level?
Devuelve la amplitud de un Marcador normal. Es necesario
especificar el número del Marcador.
Ejemplo: meas:norm:level_1? (¿Amplitud del Marcador 1
normal?)
meas:mark:delta Ajusta un Marcador a modo delta. También ajusta la
frecuencia relativa.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:delta_1 (Ajustar Marcador 1 a modo
delta)
Ejemplo: meas:mark:delta_1_10_mhz (Ajustar Marcador 1
a modo delta, frecuencia relativa 10MHz)
meas:mark:delta:
freq?
Devuelve la frecuencia relativa de un Marcador delta. Es
necesario especificar el número del Marcador.
Ejemplo: meas:delta:freq_1? (¿Frecuencia del Marcador 1
delta?)
meas:mark:delta:
level?
Devuelve la amplitud relativa de un Marcador de delta. Es
necesario especificar el número del Marcador.
Ejemplo: meas:delta:level_1? (¿Amplitud del Marcador 1
delta?)
meas:mark:tomin Desplaza un Marcador al pico mínimo.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:tomin_1 (Marcador 1 a mínimo)
meas:mark:topeak Desplaza un Marcador normal / delta al pico.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:topeak_1 (Marcador 1 pico)
meas:mark:tonp Desplaza un Marcador normal / delta al siguiente pico.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:tonp_1 (Marcador 1 al siguiente pico)
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 168 02/2007
Comando Descripción
meas:mark:tonpr Desplaza un Marcador normal / delta al siguiente pico
derecho.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:tonpr_1 (Marcador 1 al siguiente
derecho)
meas:mark:tonpl Desplaza un Marcador normal / delta al siguiente pico
izquierdo.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:tonpl_1 (Marcador 1 al siguiente pico
izquierdo)
meas:mark:tocen Desplaza un Marcador normal / delta a la frecuencia central.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:tocen_1 (Marcador 1 a la frecuencia
central)
meas:mark:tost Desplaza un Marcador normal / delta a la frecuencia inicial.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:tost_1 (Marcador 1 a la frecuencia
inicial)
meas:mark:tostp Desplaza un Marcador normal / delta a la frecuencia final.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:tostp_1 (Marcador 1 a la frecuencia
final)
meas:mark:toss Desplaza un Marcador normal / delta a la frecuencia central
+ paso.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:toss_1 (Marcador 1 a la frecuencia
central + paso)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 169
Comando Descripción
meas:mark:torefl Desplaza un Marcador normal / delta al nivel de referencia. Parámetro: 1 ~ 5 (número del Marcador) Ejemplo: meas:mark:torefl_1 (Marcador 1 al nivel de referencia)
meas:mark:trace Desplaza un Marcador normal / delta a un trazo. Parámetro: 1 ~ 5 (número del Marcador), seguido de 0 (auto), 1 (Trazo A), 2 (Trazo B), 3 (Trazo C) Ejemplo: meas:mark:trace_1_2 (Marcador 1 a Trazo B)
meas:mark:
marktable:on
Activar Tabla de Marcadores.
meas:mark:
marktable:off
Desactivar Tabla de Marcadores.
meas:mark:
peaktable:on
Activar Tabla de picos.
meas:mark:
peaktable:off
Desactivar Tabla de picos.
meas:mark:
peaktable:sortf
Ordenar Tabla de picos por frecuencia.
meas:mark:
peaktable:sorta
Ordenar Tabla de picos por amplitud.
meas:mark:
peaktrack:on
Activar rastreo de picos.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:peaktrack:on_1 (Marcador 1 rastrea el
pico)
meas:mark:
peaktrack:off
Desactivar rastreo de picos.
Parámetro: 1 ~ 5 (número del Marcador)
Ejemplo: meas:mark:peaktrack:off_1 (Marcador 1 no rastrea
más el pico)
meas:mark:
peakthres:on
Activar el umbral máximo y ajustar la amplitud.
Parámetro: umbral máximo en dB.
Ejemplo: meas:mark:peakthres:on _-30 (umbral de -30dB)
meas:mark:
peakthres:off
Desactivar el umbral máximo.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 170 02/2007
• Trazo
Comando Descripción
meas:tra Activar el modo para un trazo.
Parámetro: 1 (Trazo A), 2 (Trazo B), 3 (Trazo C), seguido
de 1 (eliminar), 2 (mantener pico), 3 (vista), 4 (vacío)
Ejemplo: meas:tra_1_2 (Trazo A al modo de mantener pico)
meas:tra:avg:on Activar el modo promedio y ajustar el número de
promediados para un trazo.
Parámetro: 1 (Trazo A), 2 (Trazo B), 3 (Trazo C), seguido
de No
Ejemplo: meas:tra:avg:on_1_20 (Promedio para Trazo A -
20 veces)
meas:tra:avg:off Desactivar el modo promedio.
Parámetro: 1 (Trazo A), 2 (Trazo B), 3 (Trazo C)
Ejemplo: meas:tra:avg:off_1 (Promedio para Trazo A -
desactivado)
meas:tra:read? Devuelve los datos del trazo.
Parámetro: 1 (Trazo A), 2 (Trazo B), 3 (Trazo C), todos (tres
trazos)
Ejemplo: meas:read_1? (Datos de Trazo A)
meas:tra:a <> b Cambia los sitios de Trazo A y B.
meas:tra:a+b> a Añade Trazo B a A.
meas:tra:a→b> a Resta Trazo B de A.
meas:tra:const? Devuelve un valor constante para ser añadido o restado.
meas:tra:const Ajusta un el valor constante para ser añadido o restado. meas:tra:a+const>a Añade un valor constante a Trazo A. meas:tra:a→const>a Resta un valor constante de Trazo A.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 171
Comando Descripción
meas:tra:det? Devuelve el modo de detección.
Parámetro: 1 (normal), 2 (muestra), 3 (pico+), 4 (promedio),
5 (cuasi-pico)
meas:tra:det Ajusta el modo de detección.
Parámetro: 1 (normal), 2 (muestra), 3 (pico+), 4 (promedio),
5 (cuasi-pico)
Ejemplo: meas:tra:det_4 (Ajusta el modo de detección a
promediado)
• Medidas de potencia
Comando Descripción
meas:ch:bw? Devuelve el ancho de banda del canal principal.
Ejemplo: 1000 kHz
meas:ch:bw Ajusta el ancho de banda del canal principal. Es necesario
especificar la unidad.
Ejemplo: meas:ch:bw_1_mhz (1MHz)
meas:adjc:bw? Devuelve el ancho de banda del canal adyacente en kHz.
Es necesario especificar el canal.
Ejemplo: meas:adjc:bw_2? (Ancho de banda del Canal 2
adyacente)
meas:adjc:bw Ajusta el ancho de banda del canal adyacente.
Es necesario especificar el canal y la unidad.
Ejemplo: meas:adjc:bw_2_1_mhz (Ajustar el ancho de
banda del Canal 2 adyacente a 1MHz)
meas:adjc:offs? Devuelve la compensación del canal adyacente en kHz. Es
necesario especificar el canal.
Ejemplo: meas:adjc:offs_2? (Compensación de Canal 2
adyacente)
meas:adjc:offs Ajusta la compensación de canal adyacente.
Es necesario especificar el canal y la unidad.
Ejemplo: meas:adjc:offs_2_1_mhz (Ajustar la
compensación de Canal 2 adyacente a 1MHz)
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 172 02/2007
Comando Descripción
meas:acpr? Devuelve estado de activación de las medidas ACPR.
Parámetro: On, Off
meas:acpr Activar/Desactivar medida ACPR.
Parámetro: On, Off
Ejemplo: meas:acpr_on (ACPR Activado)
meas:acpr:lower? Devuelve el resultado más bajo de ACPR. Es necesario
especificar 1 o 2.
Ejemplo: meas:acpr:lower_2? (¿Resultado más bajo de
ACPR 2?)
meas:acpr:upper? Devuelve el resultado más alto de ACPR. Es necesario
especificar 1 o 2.
Ejemplo: meas:acpr:upper_2? (¿Resultado más bajo de
ACPR 2?)
meas:acpr:chup Mueve el canal ACPR hacia arriba.
meas:acpr:chdown Mueve el canal ACPR hacia abajo.
meas:chspc? Devuelve el espacio del canal en kHz.
meas:chspc Ajusta el espacio de canal. Es necesario especificar la
unidad.
Ejemplo: meas:chspc_10_mhz (10MHz)
meas:ocbw? Devuelve el estado de activación/desactivación de OCBW.
Parámetro: On, Off
meas:ocbw Activar/Desactivar OCBW.
Parámetro: On, Off
Ejemplo: meas:ocbw_on
meas:ocbw:bw? Devuelve el espacio del canal en que se realiza la medida
de potencia en kHz.
meas:ocbw:per? Devuelve el porcentaje de OCBW.
meas:ocbw:per Ajusta el porcentaje de OCBW.
Ejemplo: meas:ocbw:per_90 (90 %)
meas:ndb? Devuelve el estado de activación/desactivación de N dB.
Parámetro: On, Off
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 173
Comando Descripción
meas:ndb Activar/Desactivar N dB.
Parámetro: On, Off
Ejemplo: meas:ndb_on
meas:ndb:ndb? Devuelve N dB.
meas:ndb:ndb Ajusta N dB.
Ejemplo: meas:ndb:ndb_3 (3 dB)
meas:ndb:bw? Devuelve el ancho de banda del N dB.
Ejemplo: 1000 kHz
meas:jitter? Devuelve el estado de activación/desactivación de
Oscilación de Fase.
Parámetro: On, Off
meas:jitter Activar/Desactivar Oscilación de Fase.
Parámetro: On, Off
Ejemplo: meas:jitter_on
meas:jitter:stoffs? Devuelve la Oscilación de Fase inicial.
Ejemplo: 0 kHz
meas:jitter:stoffs Ajusta la Oscilación de Fase inicial. Es necesario especificar
la unidad.
Ejemplo: meas:jitter:stoffs_0_khz
meas:jitter:stpoffs? Devuelve la Oscilación de Fase final.
Ejemplo: 50 kHz
meas:jitter:stpoffs Ajusta la Oscilación de Fase final. Es necesario especificar
la unidad.
Ejemplo: meas:jitter:stpoffs_50_khz
meas:jitter:phase? Devuelve la Oscilación de Fase en radianes.
Ejemplo: 1.234 rad
meas:jitter:time? Devuelve la Oscilación de Fase en picosegundos.
Ejemplo: 1.234 psec
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 174 02/2007
• Línea de límite
Comando Descripción
meas:lmtline:on Activar línea de límite.
Parámetro: 0 (línea de límite baja), 1 (línea de límite alta)
Ejemplo: meas:lmtline:on_0 (Activar línea de límite baja)
meas:lmtline:off Desactivar línea de límite.
Parámetro: 0 (línea de límite baja), 1 (línea de límite alta)
Ejemplo: meas:lmtline:off_0 (Desactivar línea de límite
baja)
meas:lmtline:passfail Activar/ Desactivar el test Pasa-No pasa.
Parámetro: on, off
Ejemplo: meas:lmtline:passfail_on (Activar el test Pasa-
No pasa)
meas:lmtline:
passfail:criterion?
Devuelve el criterio del test Pasa-No pasa.
Parámetro: 1 (pasa si todas las señales están en la zona), 2
(pasa si los picos están en la zona), 3 (pasa si las zonas
planas están en la zona)
meas:lmtline:
passfail:criterion
Ajusta el criterio del test Pasa-No pasa.
Parámetro: 1 (pasa si todas las señales están en la zona), 2
(pasa si los picos están en la zona), 3 (pase si las zonas
planas están en la zona)
Ejemplo: meas:lmtline:passfail:criterion_3
meas:lmtline:table? Devuelve la tabla de línea de límite.
Parámetro: on, off
meas:lmtline:table Activar/ Desactivar la tabla de línea de límite. Parámetro:
on, off
Ejemplo: meas:lmtline:table_on (Tabla de línea de límite
activada)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 175
Comando Descripción
meas:lmtline:edit Ajusta los datos de la tabla de línea de límite. Es necesario
especificar 0 (línea de límite baja), 1 (línea de límite alta) /
puntos de la línea de límite.
Ejemplo: meas:lmtline:edit_0_CR_3,100,-20,110,-30,120,-
25 (línea de límite baja, 3 puntos, 100MHz /-20dB, 110MHz
/-30dB, 120MHz /-25dB)
meas:lmtline:edit:
delall
Eliminar todos los puntos de la tabla de línea de límite.
Parámetro: 0 (línea de límite baja), 1 (línea de límite alta)
Ejemplo: meas:lmtline:edit:delall_0 (Eliminar la tabla de
línea de límite baja)
• Ancho de banda BW
Comando Descripción
con:rbw:auto Ajustar RBW a auto.
con:rbw? Devuelve el RBW (resolución de ancho de banda).
Parámetro: 0 (10 kHz), 1 (300 Hz), 2 (3 kHz), 3 (9 kHz), 4
(30 kHz), 5 (120 kHz), 6 (300 kHz), 7 (4MHz), 8 (100 kHz)
con:rbw:man Selecciona el RBW.
Parámetro: 0 (200 kHz), 1 (300 kHz), 2 (3 kHz), 3 (9 kHz), 4
(30 kHz), 5 (120 kHz), 6 (300 kHz), 7 (4MHz)
Ejemplo: con:rbw:man_1 (ajusta el RBW a 300 Hz)
con:rbw:mode? Devuelve el modo de RBW.
Parámetro: auto, manual
con:vbw:auto Ajustar VBW a auto.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 176 02/2007
Comando Descripción
con:vbw? Devuelve el VBW (ancho de banda de vídeo).
Parámetro: 0 (100 Hz), 1 (1 kHz), 2 (3 kHz), 3 (10 kHz), 4
(30 kHz), 5 (100 kHz), 6 (300 kHz), 7 (4MHz)
con:vbw:man Selecciona el VBW.
Parámetro: 0 (10 Hz), 1 (1 kHz), 2 (3 kHz), 3 (10 kHz), 4
(30 kHz), 5 (100 kHz), 6 (300 kHz), 7 (4MHz)
Ejemplo: con:vbw:man_1 (ajusta el VBW a 1 kHz)
con:vbw:mode? Devuelve modo de VBW.
Parámetro: auto, manual
con:swt:auto Ajusta el tiempo de barrido a auto.
con:swt:man Ajusta el tiempo de barrido en msec.
Ejemplo: con:swp:man_5 (Ajusta el tiempo de barrido a
5ms)
con:swt:mode? Devuelve el modo de tiempo de barrido.
Parámetro: auto, manual
con:allcouple Ajusta el RBW, VBW y el tiempo de barrido a auto.
• Disparo (Trigger)
Comando Descripción
con:trig:freerun Ajusta el disparo a modo de ejecución libre.
con:trig:video Ajusta el disparo al modo de vídeo. También ajusta el nivel
de disparo a la unidad actual.
Ejemplo: con:trig:video_-20 (Activar modo de vídeo, -
20dBm)
con:trig:single Ajusta el disparo a modo de disparo único.
con:trig:cont Ajusta el disparo a modo de disparo continuo.
con:trig:ext Ajusta el disparo a modo de disparo externo.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 177
Comando Descripción
con:trig:delay Ajusta el retraso de disparo en msec.
Ejemplo: con:trig:delay_1000 (1000ms tardanza)
con:trig:freq Ajusta la frecuencia de disparo en MHz.
Ejemplo: con:trig:freq_1 (1MHz)
• Pantalla
Comando Descripción
con:disp:dim Ajusta el nivel de brillo de pantalla.
Parámetro: 0 ~ 5
Ejemplo: con:disp:dim_2 (Ajusta el nivel de brillo a 2)
con:disp:dl Activar/ Desactivar la línea de pantalla.
Parámetro: on, off
Ejemplo: con:disp:dim_on (Activar la línea)
con:disp:dl:level Ajusta el nivel de línea de pantalla a la unidad actual.
Ejemplo: con:disp:dl:level _-50 (Ajustar la línea a -50dBm)
con:disp:title:show Ajusta y muestra el título de pantalla. El título puede ser una
combinación de mayúsculas y minúsculas.
Ejemplo: con:disp:title:show_SAtest (Ajustar el título a
SAtest)
con:disp:title:clr Borrar el título de pantalla.
con:disp:split:upper Activa y actualiza la ventana superior en modo de ventana
dividida.
con:disp:split:lower Activa y actualiza la ventana inferior en modo de ventana
dividida.
con:disp:split:alt Activa y actualiza la ventana superior e inferior en modo de
ventana dividida.
con:disp:split:full Volver al modo de pantalla completa.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 178 02/2007
• Archivo
Comando Descripción
con:file:copy:typesel Ajusta el tipo del archivo copiado.
Parámetro: 0 (trazo), 1 (línea de límite), 2 (corrección), 3
(secuencia), 4 (sistema)
Ejemplo: con:file:copy:typesel_2 (Copiar archivo de
corrección de la amplitud)
con:file:copy Copiar archivos. Es necesario especificar el archivo de
origen y destino.
Parámetro: ta/tb/tc (Trazo A/B/C), t1~10 (Trazo 1~10), lh/ll
(línea de límite alta/baja), lh1~5 (línea de límite alta 1~5),
ll1~5 (línea de límite baja 1~5), c1~5 (ajustes de corrección
1~5), q1~10 (secuencia 1~10), archivo en una memoria
USB externa
Ejemplo: con:file:copy_t10_ta (Copiar de Trazo 10 a Trazo
A)
Ejemplo: con:file:copy_ta_mytrace (Copiar Trazo A a un
archivo llamado mytrace en una memoria USB externa)
con:file:del:typesel Eliminar el tipo del archivo copiado.
Parámetro: 0 (trazo), 1 (línea de límite), 2 (corrección), 3
(secuencia), 4 (sistema)
Ejemplo: con:file:del:typesel_2 (Eliminar el archivo de
corrección de amplitud)
con:file:del Eliminar archivo.
Parámetro: ta/tb/tc (Trazo A/B/C), t1~10 (Trazo 1~10), lh/ll
(línea de límite alta/baja), lh1~5 (línea de límite alta 1~5),
ll1~5 (línea de límite baja 1~5), c1~5 (ajustes de corrección
1~5), q1~10 (secuencia 1~10), archivo en una memoria
USB externa
Ejemplo: con:file:del_t10 (Eliminar Trazo 10)
Ejemplo: con:file:del_myspace (Eliminar el archivo
myspace de una memoria USB externa)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 179
Comando Descripción
con:file:rename Renombra un archivo en la memoria USB externa. Es
necesario especificar el nombre original y cambiado.
Ejemplo: con:file:rename_myspace_myfile (Cambiar un
archivo llamado myspace a myfile)
con:file:prtsc:toprter Imprimir la imagen de pantalla a la impresora conectada.
con:file:prtsc:tofile Guardar la imagen de pantalla memoria USB externa. Es
necesario especificar el nombre de archivo.
Ejemplo: con:file:prtsc:tofile_myscreen (Guardar la
imagen de pantalla a un archivo llamado myscreen)
• Preset
Comando Descripción
con:preset Reestablece el equipo a los valores definidos en fábrica.
• Sistema
Comando Descripción
con:sys:setup:save Guardar los ajustes actuales del sistema en un archivo de
configuración.
Parámetro: 1~10
Ejemplo: con:sys:setup:save_1 (Guardar los ajustes
actuales del sistema en setup1)
con:sys:setup:recall Recuperar los ajustes actuales del sistema de un archivo de
configuración.
Parámetro: 1~10
Ejemplo: con:sys:setup:recall_1 (Recuperar los ajustes
actuales del sistema de setup1)
con:sys:gpibaddr? Devuelve la dirección GPIB actual.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 180 02/2007
Comando Descripción
con:sys:gpibaddr Ajusta la dirección GPIB.
Ejemplo: con:sys:gpib:addr_2 (Ajusta la dirección GPIB a
2)
con:sys:auxsig Activar/Desactivar la señal auxiliar.
Parámetro: on, off
Ejemplo: con:sys:auxsig_on (Activar la señal auxiliar)
con:sys:clock:date? Devuelve el ajuste de la fecha actual.
Parámetro: año / mes / día / día de semana 1 (Domigo) ~
7 (Sábado)
Ejemplo: 2006 6 24 7 (Sábado, 24 de junio, 2006)
con:sys:clock:date Ajusta la fecha.
Parámetro: año / mes / día / día de semana 1 (Domingo) ~
7 (Sábado)
Ejemplo: con:sys:clock:date_2006_6_24_7 (Junio 24,
Sábado, 2006)
con:sys:clock:time? Devuelve el ajuste de la hora actual.
Parámetro: hora / minuto / segundo
Ejemplo: 13 30 26 (1p.m., 30 minutos, 26 segundo)
con:sys:clock:time Ajusta la hora.
Parámetro: hora / minuto / segundo
Ejemplo: con:sys:clock:time_13_30_26 (1p.m., 30 minuto,
26 segundos)
con:sys:clock:show Activar/Desactivar el reloj en la pantalla.
Parámetro: on, off
Ejemplo: con:sys:clock:show_on (Reloj en la pantalla
activado)
con:sys:selftest? Devuelve el resultado de la autoprueba.
Parámetro: 0 (falla), 1 (pasa) en el siguiente orden:
GPIB/Flash/SDRAM/RTC
Ejemplo: 1 1 0 1 (GPIB pasa, Flash pasa, SDRAM falla,
RTC pasa)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 181
Comando Descripción
con:sys:lang Seleccionar idioma.
Parámetro: 1 (Inglés), 2 (Chino Simplificado)
Ejemplo: con:sys:lang_2 (Cambiar a chino simplificado)
con:sys:ser? Devuelve el número de serie.
Ejemplo: EE8300000
con:sys:swver? Devuelve la versión de software.
Ejemplo: 01.00 06/07/28 (Versión 1.00, 28 de Julio de 2006)
con:sys:fwver? Devuelve la versión de firmware.
Ejemplo: 01.00 (Versión 1.00)
con:sys:hwver? Devuelve la versión de hardware en el siguiente orden. RF,
SI, DSP, MB
Ejemplo: 01.00 01.00 01.01 01.00 (RF: versión 1.00, SI:
versión 1.00, DSP: versión 1.01, MB: versión 1.00)
con:sys:optstatus? Devuelve el estado de instalación de artículos opcionales en
el siguiente orden. 300HzRBW, EMIFilter, 10k/100kHzRBW,
TG, Demodulador, Medref (estabilidad de ±1ppm)
Parámetro: 0 (no instalado), 1 (instalado)
Ejemplo: 0 0 1 1 1 (TG, Demodulador y Medref están
instalados) • Opciones
Comando Descripción
con:opt:tg Activar/Desactivar el Generador de Seguimiento (TG).
Parámetro: on, off
Ejemplo: con:opt:tg_on (TG activado)
con:opt:tg:level? Devuelve el nivel del TG.
con:opt:tg:level Ajusta el nivel del TG.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 182 02/2007
Comando Descripción
con:opt:tg:norm Activar/Desactivar normalización del TG.
Parámetro: on, off
Ejemplo: con:opt:tg:norm_on (Normalización activada)
con:opt:tg:offset Ajusta el nivel de compensación del TG.
con:opt:ge:refval? Devuelve el valor de referencia del TG.
con:opt:ge:refval Ajusta el valor de referencia del TG.
con:opt:dm:fm Activar/Desactivar FM en el demodulador.
Parámetro: on, off
Ejemplo: con:opt:dm:fm_on (FM activado)
con:opt:dm:am Activar/Desactivar AM en el demodulador.
Parámetro: on, off
Ejemplo: con:opt:dm:am_on (AM activado)
con:opt:dm:spk Activar/Desactivar la salida de audio en el demodulador.
Parámetro: on, off
Ejemplo: con:opt:dm:spk_on (Salida de audio activada)
con:opt:dm:vol Ajusta el volumen de la salida de audio del demodulador.
con:opt:dm:sql? Devuelve el nivel de ruido del demodulador.
con:opt:dm:sql Ajusta el nivel de ruido del demodulador.
con:opt:bat? Devuelve el nivel de batería.
con:opt:extreffreq? Devuelve la frecuencia de referencia externa.
con:opt:extreffreq Ajusta la frecuencia de referencia externa.
• Secuencia
Comando Descripción
con:seq:runmode Seleccionar el modo de ejecución de secuencia.
Parámetro: 1 (repetido), 2 (único)
Ejemplo: con:seq:runmode_2 (Modo de ejecución de
secuencia-único)
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 183
Comando Descripción
con:seq:runseq Ejecutar la secuencia.
Parámetro: índice de secuencia, 1 ~ 10
Ejemplo: con:seq:runseq_2 (Ejecutar secuencia 2)
con:seq:stopseq Interrumpir la secuencia que se ejecuta.
con:seq:delallseq Eliminar todas las secuencias programadas.
con:seq:delseq Eliminar una secuencia.
Parámetro: índice de secuencia, 1 ~ 10
Ejemplo: con:seq:delseq_2 (Eliminar secuencia 2)
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 184 02/2007
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 185
8 MANTENIMIENTO
8.1 FUNCIONAMIENTO CON BATERÍA (Opcional)/ CORRIENTE CONTINUA
El módulo de funcionamiento con Batería/Corriente Continua (DC) es un
elemento opcional para poder usar el AE-966/967 en el exterior, utilizando la batería y la salida de DC del coche.
8.1.1 Funcionamiento con Batería
Apague el interruptor principal antes de introducir
o quitar el pack de baterías.
Quitar / Introducir el pack de baterías Saque la batería si el equipo no va a ser utilizado durante mucho
tiempo. Gire el tornillo para abrir el compartimiento de las baterías.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 186 02/2007
1.- Pulse la tecla Option. Option
2.- Pulse F3 (Battery). El icono de nivel
aparece en la parte inferior de la pantalla. Battery F 3
Comprobar el nivel de la batería
Totalmente cargada
75 % ~ 50 %
50 % ~ 25 %
Menos del 25 %
Nota: Se compruebe o no manualmente, el equipo muestra el icono
durante 5 segundos cada 30 minutos. Parámetros Tiempo de uso: 3 horas (típico).
Tiempo de carga: 3 horas (típico)
8.1.2 Funcionamiento con corriente continua Pasos a realizar
Conecte el cable de alimentación de DC al
conector de entrada del panel trasero. Parámetro 12V, 40W máximo
NOTA: El cable de alimentación de DC (con un enchufe ligero para el uso de
coche) está disponible como otro artículo opcional, AA-12.
MANUAL DE INSTRUCCIONES AE-966 / 967
02/2007 Página 187
• Comprobar estado de instalación del módulo de Batería/DC
1.- Pulse la tecla System. System
2.- Pulse F6 (More). More... F 6
3.- Pulse F4 (System Config On). La
configuración aparece en pantalla.
System ConfigOn Off F 4
Pasos a realizar
4.- El signo de Battery muestra el estado de
instalación, instalado (marcado) o no instalado
(no marcado).
Instalado
No instalado
8.2 SUSTITUCIÓN DEL FUSIBLE DE RED
El portafusibles está situado en la propia base de red. Para la sustitución del fusible:
1) Desconectar el cable de red.
2) Mediante un destornillador apropiado extraer la tapita del portafusibles.
3) Sustituir el fusible dañado por otro de iguales características.
EL FUSIBLE DEBE SER DEL TIPO 5 x 20 mm,250 V, LENTO T y de 1.6 A. EL INCUMPLIMIENTO DE ESTAS INSTRUCCIONES PODRÍA DAÑAR EL EQUIPO.
4) Reinsertar la tapita portafusibles.
MANUAL DE INSTRUCCIONES AE-966 / 967
Página 188 02/2007
8.3 RECOMENDACIONES DE LIMPIEZA
PRECAUCIÓN Para limpiar la caja, asegurarse de que el equipo está desconectado.
PRECAUCIÓN
No utilizar para la limpieza hidrocarburos aromáticos o disolventes clorados. Estos productos pueden atacar a los materiales utilizados en la construcción de la caja.
La caja se limpiará con una ligera solución de detergente con agua y aplicada
mediante un paño suave humedecido. Secar completamente antes de volver a usar el equipo.
USER’S MANUAL. AE-966 / 967
Eng
lish
T A B L E O F C O N T E N T S 1 GENERAL................................................................................................................. 1
1.1 Description......................................................................................................... 1 1.2 Specification .................................................................................................... 3
2 SAFETY RULES ..................................................................................................... 7
2.1 General .............................................................................................................. 7 2.2 Descriptive Examples of Over-Voltage Categories ........................................... 8
3 INSTALLATION ........................................................................................................ 9
3.1 Power Supply ................................................................................................... 9 3.2 Support feet adjustement................................................................................... 9
4 QUICK USE GUIDE................................................................................................ 11
4.1 General description.......................................................................................... 11 4.2 Guide ............................................................................................................... 11
4.2.1 Frequency and Span ............................................................................... 11 4.2.2 Amplitude................................................................................................. 12 4.2.3 Autoset..................................................................................................... 12 4.2.4 Marker...................................................................................................... 13 4.2.5 Peak Search ............................................................................................ 13 4.2.6 Trace........................................................................................................ 14 4.2.7 Power Measurement................................................................................ 14 4.2.8 Limit Line ................................................................................................. 15 4.2.9 Bandwidth ................................................................................................ 16 4.2.10 Trigger ..................................................................................................... 16 4.2.11 Display ..................................................................................................... 16 4.2.12 File .......................................................................................................... 17 4.2.13 Preset ...................................................................................................... 18 4.2.14 System..................................................................................................... 18 4.2.15 Option ...................................................................................................... 18 4.2.16 Sequence................................................................................................. 19
5 MENU TREE........................................................................................................... 21
5.1 Frequency, Span, Autoset, Amplitude(1 of 2).................................................. 21 5.2 Amplitude (2 of 2), Marker ............................................................................... 22 5.3 Peak Search, Trace ......................................................................................... 23 5.4 Meas, Limit Line............................................................................................... 25 5.5 BW, Trigger, Display........................................................................................ 27 5.6 File ................................................................................................................... 28 5.7 System............................................................................................................. 29 5.8 Option, Sequence ............................................................................................ 30
USER’S MANUAL AE-966 / 967
6 INSTRUCTIONS DE MANEJO............................................................................... 31
6.1 Description of the controls and elements......................................................... 31 6.1.1 Front Panel description............................................................................ 31 6.1.2 Rear Panel description. ........................................................................... 33
6.3 Main functions.................................................................................................. 35 6.3.1 Frequency/Span functions. ...................................................................... 35 6.3.2 Amplitude................................................................................................. 42 6.3.3 Autoset..................................................................................................... 53 6.3.4 Marker...................................................................................................... 56 6.3.5 Peak Search ............................................................................................ 64 6.3.6 Trace........................................................................................................ 70 6.3.7 Power Measurement................................................................................ 81 6.3.8 Limit Line ................................................................................................. 90 6.3.9 Bandwidth ................................................................................................ 96 6.3.10 Trigger ................................................................................................... 104 6.3.11 Display ................................................................................................... 107 6.3.12 File/Print................................................................................................. 113 6.3.13 Preset Function...................................................................................... 123 6.3.14 System................................................................................................... 124 6.3.15 Sequence (Seq)..................................................................................... 135 6.3.16 Tracking Generator................................................................................ 141 6.3.17 Demodulator (Optional) ......................................................................... 143 6.3.18 EMI Filter (Optional)............................................................................... 146 6.3.19 PC Software........................................................................................... 148 6.3.20 Remote Control...................................................................................... 158
7 COMMAND SYNTAX............................................................................................ 161
7.1 Comand set ................................................................................................... 162 8 MAINTENANCE ................................................................................................... 177
8.1 Battery / DC Operation .................................................................................. 177 8.1.1 Battery Operation................................................................................... 177 8.1.2 DC Operation......................................................................................... 178
8.2 Replacing the mains fuse .............................................................................. 179 8.3 Cleaning recommendations ........................................................................... 180
USER’S MANUAL AE-966 / 967
02/2007 Page 1
Eng
lish
Spectrum Analyzer AE-966 & AE-967
1 GENERAL 1.1 Description
The AE-966 and AE-967 spectrum analysers cover a frequency band from 9 kHz to 3 GHz and allow a stable operation with span of 2 kHz/div to 3 GHz/div.
The AE-966 is the basic model whereas the AE-967 includes a Tracking
Generator, which turns the AE-967 into a highly useful tool for the response measurement of filters, amplifiers, attenuators and, generally speaking, any kind of radio frequency system.
The plentiful measurement functions like markers, traces, power measurement,
limit line, dual display and trigger make measurement more easily and quickly. The exit direct VGA is ideal to realize presentations.
The Tracking Generator available in model AE-967 offers the frequency
response test with the same frequency band. The RS232 interface and USB allows the connection between the unit and PC. Users can develop their own applications software. DC 12V power supply (optional) allows user to carry this unit to drive around for frequency monitoring. With the carrying case, this unit is easy to carry and operate in the filed service. 9k and 120k EMI filter and quasi-peak detector (optional) can perform the EMC test.
Characteristics:
- Low noise floor: -117dBm to 600MHz, 3k RBW.
- Fast sweep: 50ms ~ 25.6s.
- Tracking generator (only AE-967).
- Autoset.
- 5 markers with Delta Marker and Peak functions.
- 3 traces
- Power measurements: ACPR, OCBW, N-dB, Phase Jitter.
USER’S MANUAL AE-966 / 967
Page 2 02/2007
- Pass/Fail test with Limit Line editing.
- Split windows with separate settings.
- Sequence programming (user-defined macro).
- 6.4 ” TFT color LCD, 640 x 480 resolution.
- Phone output (available in optional Demodulator).
- AC/DC/Battery multi-mode power operation.
- Compact size: 330(W) x 170(H) x 340(D) mm.
- Light weight: 5.8kg (without options).
Interface
- USB host for storage device connection and display image printout
- USB slave/RS232/GPIB(optional) for PC software connection and remote control.
- Direct VGA display image output.
- Reference signal input/output for synchronization
- External trigger signal input.
Options
- EMI filter with 9kHz/120kHz RBW and 6-dB bandwidth.
- Battery pack.
- AM/FM Demodulator.
- 300Hz/10kHz/100kHz RBW.
- GPIB interface.
USER’S MANUAL AE-966 / 967
02/2007 Page 3
Eng
lish
1.2 Specification FREQUENCY Range Of 9 kHz to 3.0 GHz Accuracy To see base of times. Span Accuracy To see base of times. Span Range 2 kHz to 3.0 GHz in 1/2/5 sequence, full span,
zero span. Phase Noise -80 dBc/Hz 1 GHz 20 KHz Offset typ. Base of Times ±10 ppm, of 0 to 50 °C, 5 ppm/yr BANDWIDTH RBW Range 3 kHz, 30 kHz, 300 kHz, 4 MHz RBW Accuracy ± 15% VBW Range 10 Hz to 1 MHz in 1-3 steps. Sweep Time Range 50 ms a 25,6 s AMPLITUDE Measurement Range 1 MHz to 15 MHz 15 MHz to 600 MHz 600 MHz to 2,3 GHz 2,3 GHz to 3,0 GHz Reference Level Range -30 dBm to + 20 dBm, overload protection. Accuracy ±1 dB it 100 MHz Frequency Flatness ±1 dB Display Range Linearity ±1 dB over 70 dB Overload Protection +30 dBm, ±25 VDC Average Noise Floor -135 dBm/Hz: 1 MHz to 15 MHz -152 ± 1dBm/Hz: 15 MHz to 600 MHz -149 ± 1dBm/Hz: 600 MHz to 2,3 GHz -147 ± 1dBm/Hz: 2,3 GHz to 3,0 GHz Harmonic Distortion <-60dBc RF Input < -40dBm. Non-Harmonic Spurious <-110 dBm to 3kHz RBW Third Intermodulation <-70 dBc Input -40 dBm Trace Detection 3 traces with Peak, Maximum hold, Freeze,
Average, and Trace Math INPUT RF Input Overload Protection +30 dBm Continuous. Impedance 50 Ω nominal TG Output VSWR <2:1, ref level. 0 dBm Connector Type N Female External Reference Clock 1 MHz, 1,544 MHz, 2,048 MHz, 5 MHz, 10
MHz, 10,24 MHz, 13 MHz, 15,36 MHz, 15,4 MHz, 19,2 MHz
USER’S MANUAL AE-966 / 967
Page 4 02/2007
OTHER FUNCTIONS Internal Memory 10 Traces, 10 Setup Info, 10 Limit lines, 5
Corrections, 10 Sequences. Power Measurements ACPR, OCBW, Channel power, N dB BW y
Phase Jitter. Ref. Clock Output 10 MHz CONNECTORS RS-232 For the overturned one of the screen to a PC
(free software). External Trigger Input BNC, TTL +5V signal. Connector USB Front Panel: Type A. Rear Panel: Type B mini. DC Voltaje Output SMB Male, +9V/100mA max output. TRACKING GENERATOR (only AE-967) Frequency Range 9 kHz to 3,0 GHz Amplitude Range -50 dBm to 0 dBm Amplitude Accuracy ±1 dB (0 dBm, 100 MHz) Amplitude Flatness ±1 dB (0 dBm). Harmonics <-30 dBc typical. Reverse Power +30 dBm Impedance 50 Ω nominal TG Output VSWR < 2:1 GPIB INTERFACE (optional) EMI FILTER (optional) RBW Selections 9 kHz and 120 kHz, 3dB bandwidth RBW Accuracy 15 % AM/FM DEMODULATOR AND 10kHz & 100kHz RBW (optional). Demodulator AM, FM. Output Internal Speaker, 3.5mm stereo jack wired for
mono. RBW Selections 10 kHz and 100 kHz, 3dB bandwidth. RBW Accuracy 15 %.
USER’S MANUAL AE-966 / 967
02/2007 Page 5
Eng
lish
GENERAL Display 640 x 480 high-res color TFT LCD. Markers 10 markers for peaks: 5 normal-delta marker
pairs. Functions: Delta, Peak, Marker Track Autoset Function Auto tuning the measurement result for
observation. Sequence Automated test by user defined macros without
any remote control.
POWER SUPPLY AC Input 100 to 240 V AC, 50-60 Hz. Internal Battery (optional) Li-Ion rechargeable battery pack with integrated
loader. External DC 12 V. Consumption 40 W.
OPERATION ENVIRONMENT CONDITIONS Indoor use Altitude Up to 2000 m Optimum operating temper. From 18 to 28 °C Relative humidity From 0 to 90 %
STORAGE ENVIRONMENT CONDITIONS Temperature range From 0 to 40 °C Relative Humidity < 85% MECHANICAL CHARACTERISTICS Dimensions W 330 x H 170 x D 340 Weight 5.8 kg without options.
INCLUDED ACCESSORIES Power cord CA-05 User´s Manual 0 MI1486 CD — Software 0 DK0742 N-BNC adapter 2x AD059
OPTIONS GPIB Interface OP-966-A Battery Pack OP-966-CU (2 x Li-ion battery 202S) Resolution Filter 300Hz RBW OP-966-E (*) Resolution Filter 9KHz and 120KHz RBW OP-966-D (*) AM/FM demodulator and 10kHz & 100kHz RBW filter OP-966-M (*)
(*) Only one of these options can be installed. Installation in factory on having done the order of the equipment. It is not possible to realize the installation later.
USER’S MANUAL AE-966 / 967
Page 6 02/2007
USER’S MANUAL AE-966 / 967
02/2007 Page 7
Eng
lish
2 SAFETY RULES
2.1 General
* The safety can turn compromised if there are not aplied the instructions given in this manual.
* To use the equipment only in system or devices with the negative of measurement connected to the potential of land.
* This is a class I equipment, for safety reasons plug it to a supply line with the corresponding ground terminal.
* This equipment can be used in Over-Voltage Category II installations and Pollution Degree 2 environment. (2.2).
* When using some of the following accessories use only the specified ones to ensure safety:
Power cord Battery (Optional)
* Observe all specified ratings both of supply and measurement.
* Remember that voltages higher than 70 V DC or 33 V AC rms are dangerous.
* Use this instrument under the specified environmental conditions.
* The user is only authorized to carry out the following maintenance operations:
Replace the battery pack of the specified type and value.
On the Maintenance paragraph the proper instruction are given.
Any other change on the equipment should be carried out by qualified personnel.
* The negative of measure is at ground potential.
* Do not obstruct the ventilation system.
* Use for the signal inputs/outputs, specially when working with high levels, appropriate low radiation cables.
* Follow the cleaning instructions described in the Maintenance paragraph.
USER’S MANUAL AE-966 / 967
Page 8 02/2007
DIRECT CURRENT
ALTERNATING CURRENT
FRAME TERMINAL
ON (Supply)
OFF (Supply)
DOUBLE INSULATION
(Class II protection)
CAUTION
(Risk of electric shock)
CAUTION REFER TO MANUAL
FUSE
GROUND TERMINAL
PROTECTIVE CONDUCTOR
2.2 Descriptive Examples of Over-Voltage Categories Cat I Low voltage installations isolated from the mains. Cat II Portable domestic installations. Cat III Fixed domestic installations. Cat IV Industrial installations.
USER’S MANUAL AE-966 / 967
02/2007 Page 9
Eng
lish
3 INSTALLATION
3.1 Power Supply
The AE-966 and AE-967 spectrum analysers require a mains power source from 100 to 240 V AC 50 to 60 Hz ± 10%. Also they allow to be fed to 12 V DC or rechargeable batteries using the integrated loader.
3.2 Support feet adjustement
Spectrum analysers AE-966 and AE-967 possess four support feet and one carrying handle. These feet allow to orientate the spectrum analyser under an ideal angle of visualisation. For desktop use, lock the feet in place as following figures:
Foot with tip
Foot without tip
Push forward the tip
Pull back the tip
Turn up the tip to the end can makehigher angle of elevation
Turn up the tip to the end can makelower angle of elevation
Figure 1.- Spectrum analyser’s support feb.
USER’S MANUAL AE-966 / 967
Page 10 02/2007
USER’S MANUAL AE-966 / 967
02/2007 Page 11
Eng
lish
4 QUICK USE GUIDE
4.1 General description
The quick use guide provides the information of measurement-oriented operation. Every operation is titled with a measurement demand and followed by the corresponding operation sequence of the keys on the front panel and terminals on the rear panel.
4.2 Guide
4.2.1 Frequency and Span
Teclas función Description
Frequency → F1 Span → F1
Set Center Frequency and Span.
Frequency → F2, F3 Set Start and Stop Frequency.
Frequency → F4 Set Frequency Step.
Span → F2 Activate Full Span (3.0GHz)
Span → F3 Activate Zero Span (Time Domain)
Span → F4 Activate Zero Span (Time Domain)
USER’S MANUAL AE-966 / 967
Page 12 02/2007
4.2.2 Amplitude
Funtion Keys Description
Amplitude → F1 Set Reference Level
Amplitude → F2 Select Vertical Scale
Amplitude → F3 →F1∼F3 Select Unit (dBm/dBmV/dBuV)
Amplitude → F4 Set External Offset
Amplitude →F5→F2 Activate Amplitude Correction
Amplitude →F5→F1→F1 Select Amplitude Correction Set
Amplitude →F5→F1→F2 Delete Amplitude Correction Item
Amplitude →F5→F1→F3→F2 Delete Amplitude Correction Set
Amplitude →F5→F1→F4 Undo Correction Item/Set Deletion
Amplitude →F5→F1→F5 Save Amplitude Correction Set
Amplitude →F6→F1 Select Input Impedance (50Ω/75Ω)
Amplitude →F6→F2 Set Input Impedance Offset
4.2.3 Autoset
Funtion Keys Description
Autoset → F1 Run Autoset.
Autoset → F2 Set Amplitude Floor.
Autoset → F3 Set Frequency View Span.
USER’S MANUAL AE-966 / 967
02/2007 Page 13
Eng
lish
4.2.4 Marker
Funtion Keys Description
Marker → F1, F2 Activate Normal Marker
Marker →F1, F2, F3 Activate Delta Marker
Marker →F6→F3 Activate All Normal Markers
Marker →F4 o Peak Search→F1
Move Marker to Peak
Marker →F4,F5 o Peak Search→F5
Move Marker and Peak to Center
Peak Search→F6→F4 Track Marker on Peak
Marker →F6→F4→F1∼F5 Move Marker to Various Locations
Marker →F6→F2 Show Marker Table
Marker →F6→F1 Put Marker on Trace
4.2.5 Peak Search
Funtion Keys Description Peak Search→F1 or Marker→F4
Search Peak Signal
Peak Search→F2, F3 (right), F4 (left)
Search Next Peak
Peak Search→F5 or Marker→F4, F5
Search Peak and Move to Center
Peak Search→F6→F4 Track Marker on Peak
Peak Search→F6→F5 Search Minimum Amplitude
Peak Search→F6→F1 Show Peak Table
Peak Search→F6→F2 Sort Peaks in Peak Table
Peak Search→F6→F3 Set Peak Threshold
USER’S MANUAL AE-966 / 967
Page 14 02/2007
4.2.6 Trace
Funtion Keys Description
Trace→F1 Activate Trace
Trace→F2 Update Trace in Real-Time (Default)
Trace→F3 View Peak Hold Trace
Trace→F4 Freeze Trace
Trace→F5 Hide Trace
Trace→F6→F1 o BW→F4 View Averaged Trace
Trace→F6→F2→F1~F5 Run Trace Math
Trace→F6→F3→F1~F5 Select Signal Detection Mode
4.2.7 Power Measurement
Funtion Keys Description
Meas→F2 Activate ACPR
Meas→F1→F1 Set ACPR Main Channel Bandwidth
Meas→F1→F2 Set ACPR Channel Space
Meas→F1→F4→F2, F4 Set Adjacent Channel Offset
Meas→F1→F4→F1, F3 Set Adjacent Channel Bandwidth
Meas→F4 Move ACPR Channel Up
Meas→F5 Move ACPR Channel Down
Meas→F3 Activate OCBW
USER’S MANUAL AE-966 / 967
02/2007 Page 15
Eng
lish
Funtion Keys Description
Meas→F1→F1 Set OCBW Channel Bandwidth
Meas→F1→F2 Set OCBW Channel Space
Meas→F1→F3 Set OCBW %
Meas→F4 Move OCBW Channel Up
Meas→F5 Move OCBW Channel Down
Meas→F6→F1 Activate N dB
Meas→F6→F2 Set N dB Value
Meas→F6→F3 Activate Phase Jitter
Meas→F6→F4→F1 (Start), F2 (Stop)
Set Phase Jitter Offset
4.2.8 Limit Line
Funtion Keys Description Limit Line→F1 (High), F2 (Low)
Activate Limit Line
Limit Line→F3→F1 Select Limit Line for Edit
Limit Line→F3→F2 Activate Limit Line Edit Table
Limit Line→F3→F3 (Delete) Delete Limit Line Table Item
Limit Line→F3→F4→F1, F2 Delete All Table Item
Limit Line→F3→F5 Undo Last Deletion
Limit Line→F4 Run Pass/Fail Test
Limit Line→F5 Select Pass/Fail Condition
USER’S MANUAL AE-966 / 967
Page 16 02/2007
4.2.9 Bandwidth
Funtion Keys Description
BW→F1 Select RBW
BW→F2 Select VBW
BW→F3 Set Sweep Time
BW→F4 or Trace→F6→F1 Set Trace Average Number
BW→F5 Reset RBW/VBW/Sweep to Auto
4.2.10 Trigger
Funtion Keys Description
Trigger→F1 Select Free Run (Default)
Trigger→F2 Select Video/External Trigger
Trigger→F3 Select Trigger Mode
Trigger→F4 Set Trigger Delay
Trigger→F5 Set Trigger Frequency
Trigger→F6 Run Trigger (in Single/Continuous)
4.2.11 Display
Funtion Keys Description
Display→F1 Change Dimmer Level
Display→F2 Show Display Line
Display→F3→F1 Clear Title
USER’S MANUAL AE-966 / 967
02/2007 Page 17
Eng
lish
Funtion Keys Description
Display→F3→F2~F4 Enter Title
Display→F3→F5 Show Title
Display→F4→F1 (Upper), F2 (Lower)
Activate Split Display
Display→F4→F3 Alternate Upper/Lower Sweep
Display→F4→F4 Switch Split Display to Full Screen
4.2.12 File
Funtion Keys Description
File→F1→F1→F1~F5 Select Copy Source File
File→F1→F2→F1~F5 Select Copy Destination File
File→F1→F3 Editar Nombre de Archivo Copiado
File→F1→F4 Edit Copied File Name
File→F2→F1→F1~F5 Copy Selected File
File→F2→F2 Select File for Deletion
File→F3→F1 Delete Selected File
File→F3→F2 Rename File
File→F4→F1 Confirm New File Name
File→F4→F2→F2 Printout Display Image
File→F4→F2→F1 Save Display Image to USB Drive
USER’S MANUAL AE-966 / 967
Page 18 02/2007
4.2.13 Preset
Funtion Keys Description
Preset Recall Preset Panel Setting
4.2.14 System
Funtion Keys Description System→F1→F1~F2 (Select), F3 (Save)
Save Setup
System→F1→F1~F2 (Select), F4 (Recall)
Recall Setup
System→2 Set GPIB Address
System→F3→F1~F4 Show RS-232C Configuration
System→F4 Activate Auxiliary Signal
System→F6→F1→F1→F1~F4 Set Date
System→F6→F1→F2→F1~F3 Set Time
System→F6→F1→F3 Activate Clock Display
System→F6→F2→F1~F4 View Self Test Result
System→F6→F4 View System Configuration
System→F6→F5→F1 Select Language
4.2.15 Option
Funtion Keys Description
Option→F1→F1 Activate Tracking Generator
Option→F1→F2 Set Tracking Generator Amplitude
USER’S MANUAL AE-966 / 967
02/2007 Page 19
Eng
lish
Funtion Keys Description Option→F1→F3→F1 (No), F2 (Yes)
Normalize Tracking Generator
Option→F1→F4 Activate Normalized TG
Option→F1→F5 Set Ref Level for TG Normalization
Option→F2→F1 Activate FM Demodulator
Option→F2→F2 Activate AM Demodulator
Option→F2→F3 Activate Phone Output
Option→F2→F4 Set Phone Output Volume
Option→F2→F5 Set Squelch Level
Option→F3 View Battery Level
Option→F4 Set Ext. Reference Signal Frequency
4.2.16 Sequence
Funtion Keys Description
Sequence→F1, F2 Select Sequence Set
Sequence→F3→F1 Start Sequence Edit
Sequence→F3→F2 Insert 100ms Delay
Sequence→F3→F3 Insert Pause in Sequence
Sequence→F3→F4→F1~F2 Insert Another Sequence Set
Sequence→F3→F5 Stop Sequence Edit
Sequence→F3→F6→F1 Insert Item to Sequence Set
Sequence→F3→F6→F2 Save Sequence Set
USER’S MANUAL AE-966 / 967
Page 20 02/2007
Funtion Keys Description
Sequence→F3→F6→F3 Delete Sequence Item
Sequence→F3→F6→F4→F1, F2
Delete Sequence Set
Sequence→F3→F6→F5 Undo Sequence Item/Set Delete
Sequence→F4→F1 Select Sequence Run Mode
Sequence→F4→F2 Run Sequence
Sequence→F5→F1 (No), F2 (Yes)
Delete All Sequence Set
USER’S MANUAL AE-966 / 967
02/2007 Page 21
Eng
lish
5 MENU TREE
The menu tree gives a brief overview of user interface structure. The more detailed explanation for each function key is described in this Chapter 5.
5.1 Frequency, Span, Autoset, Amplitude(1 of 2)
Center1.5 GHz F 1
Start0 kHz F 2
Stop3 GHz F 3
Step0 kHz F 4
Frequency
Span3 GHz F 1
Full Span F 2
Zero Span F 3
Last Span F 4
Span
SpanAuto Man F 3
Autoset F 1
Autoset
Amp.FloorAuto Man F 2
Ref.Level-30.0dBm F 1
Scale dB/Div10 5 2 1 F 2
Units... F 3
Ext.Gain0dB F 4
Corrections.. F 5
More F 6
dBm F 1
dBmV F 2
dBuV F 3
Return F 6
Amplitude
USER’S MANUAL AE-966 / 967
Page 22 02/2007
5.2 Amplitude (2 of 2), Marker
Scale dB/Div10 5 2 1 F 2
Units... F 3
Corrections.. F 5
More F 6
InputZ50Ω 75Ω
F 1
Input Z Cal5.9dB F 2
Return F 6
Select1 2 3 4 5 F 1
Delete F 2
Delete All.. F 3
Undelete F 4
Return F 6
Edit... F 1
CorrectionOn Off F 2
Return F 6
No F 1
Yes F 2
Return F 6
Ref.Level-30.0dBm F 1
Ext.Gain0dB F 4
Amplitude
Save Now F 5
Marker1 2 3 4 5 F 1
On Off F 2
To Peak F 4
Mkr Center F 5
More F 6
Marker TraceAuto A B C F 1
Mkr to... F 4
Return F 6
Mkr Center F 1
Mkr Start F 2
Mkr Stop F 3
Mkr CFStep F 4
Return F 6
Mkr Ref Lvl F 5
Marker
ModeNormal ∆Mkr F 3
Marker TableOn Off F 2
All MkrsOn Off F 3
USER’S MANUAL AE-966 / 967
02/2007 Page 23
Eng
lish
5.3 Peak Search, Trace
Pk Search F 1
Next Peak F 2
Next PkRight F 3
Next Pk Left F 4
More F 6
Peak TableOn Off F 1
Pk ThresholdOn Off F 3
TrackOn Off F 4
Return F 6
Mkr Center F 5 Min Search F 5
Peak Search
Peak SortFreq Amp F 2
USER’S MANUAL AE-966 / 967
Page 24 02/2007
Clear F 2
Peak Hold F 3
View F 4
Blank F 5
More F 6
AVGOn Off
20F 1
Trace Math.. F 2
Detection.. F 3
Return F 6
Normal F 1
Sample F 2
Peak+ F 3
AVG F 4
Return F 6
A B F 1
A+B A F 2
Return F 6
QPeak F 5
A-B A F 3
A+const A F 4
Trace
TraceA B C F 1
A-const A F 5
USER’S MANUAL AE-966 / 967
02/2007 Page 25
Eng
lish
5.4 Meas, Limit Line
CH Up F 4
CH Down F 5
More F 6
ChannelSetup... F 1
N dB F 2
CH BW F 1
CH SPC F 2
OCBW % F 3
ADJ CHOffset... F 4
Return F 6
Adj CH BW1 F 1
Adj CH Offs1 F 2
Return F 6
Adj CH BW2 F 3
Adj CH Offs2 F 4
Phase JitterOn Off F 3
Phase JitterSetup F 4
Return F 6
StartOffset F 1
StopOffset F 2
Return F 6
Meas
ACPROn Off F 2
OCBWOn Off F 3
N dB BWOn Off F 1
USER’S MANUAL AE-966 / 967
Page 26 02/2007
Edit... F 3
Edit TableOn Off F 2
Delete F 3
Return F 6
No F 1
Yes F 2
Return F 6
Delete All.. F 4
Undelete F 5
Limit Line
H LimitOn Off F 1
L LimitOn Off F 2
Pass/FailOn Off F 4
Pass/Fail___ F 5
LimitLow High F 1
USER’S MANUAL AE-966 / 967
02/2007 Page 27
Eng
lish
5.5 BW, Trigger, Display
RBWAuto Manu F 1
VBWAuto Manu F 2
All Auto F 5
BW
Swp TmAuto Manu F 3
AVGOn Off 20 F 4
Free Run F 1
Trigger ModeNorm. Sgl. Cont. F 3
Trigger Freq1.5GHz F 5
Trigger
TriggerCondition
Video Ext.F 2
Trigger Delay50ms F 4
Run Now F 6
LCD Dimmer F 1
(Capital Letter) F 2
Title... F 3
Split Window... F 4
Return F 6
Clear Title F 1
Show Title F 5
Upper F 1
Lower F 2
Return F 6
(Small Letter) F 3
(Symbol) F 4
AlternateSweep F 3
Full Screen F 4
Display
Display LineOn Off F 2
USER’S MANUAL AE-966 / 967
Page 28 02/2007
5.6 File
Copy... F 1
Source.. F 1
Destination.. F 2
Return F 6
Delete... F 2
Rename... F 3
Print Screen.. F 4
Return F 6
Edit File Name F 3
Copy Now F 4
Return F 6
Type... F 1
Delete Now F 2
Return F 6
Edit File Name F 1
Return F 6
To Printer F 1
Return F 6
Edit File Name F 1
Print Now F 2To Ext.Memory... F 2
File Type
FileType
FileType
FileType
File
TraceInt. Ext. F 1
LimitInt. Ext. F 2
CorrectionInt. Ext. F 3
Seq.Int. Ext. F 4
SetupInt. Ext. F 5
Confirm F 2
USER’S MANUAL AE-966 / 967
02/2007 Page 29
Eng
lish
5.7 System
Serial Port.. F 3
Service... F 5
RF Diagno... F 3
Return F 6
SystemClock... F 1
Self Test... F 2
Return F 6
Date... F 1
Time... F 2
(English) F 1
Return F 6 Return F 6
GPIBPass Fail F 1
FlashPass Fail F 2
Year F 1
Month F 2
Day F 3
Return F 6
Hour F 1
Minute F 2
Second F 3
Return F 6
Language F 5
System ConfigOn Off F 4
GPIB Add8 F 2
More... F 6
ClockOn Off F 3
SDRAMPass Fail F 3
RTCPass Fail F 4
Return F 6
Setup6 7 8 9 10 F 2
Save/RecallSetup.. F 1
Save Now F 3
Recall Now F 4
Stop1 F 3
Return F 6
Baud115200 F 1
ParityNone F 2
Data8 F 4
*
System
*
Setup1 2 3 4 5 F 1
Day of Week F 4
Aux SigOn Off F 4
* Submenu only for service personnel
USER’S MANUAL AE-966 / 967
Page 30 02/2007
5.8 Option, Sequence
TG... F 1
Demod... F 2
Battery F 3
TGOn Off F 1
TG Level F 2
ExecuteNormalization..
F 3
Ref Value F 5
Return F 6
FMOn Off F 1
AMOn Off F 2
Volume F 4
Squelch F 5
Return F 6
Option
No F 1
Yes F 2
Return F 6
Norm CorrOn Off F 4
SPKOn Off F 3
Ext Ref Freq10MHz F 4
Start Edit F 1
Delay ms100 X F 2
Wait to go F 3
Do Seq... F 4
Seq.Index6 7 8 9 10 F 2
Return F 6
Stop Edit F 5
More F 6
No F 1
Yes F 2
Return F 6
Insert F 1
Save F 2
Undelete F 5
Return F 6
Select Seq6 7 8 9 10 F 2
Edit... F 3
Run... F 4
DeleteSeq All... F 5
Delete F 3
Delete All.. F 4
Run Now F 2
Return F 6
No F 1
Yes F 2
Return F 6
Seq
Select Seq1 2 3 4 5 F 1 Seq.Index
1 2 3 4 5 F 1
Run ModeRept. Sngl. F 1
USER’S MANUAL AE-966 / 967
02/2007 Page 31
Eng
lish
6 INSTRUCTIONS DE MANEJO
6.1 Description of the controls and elements 6.1.1 Front Panel description.
F 1
F 2
F 3
F 4
F 5
F 6
Frequency
Span
Amplitude
Autoset
BW
1 2 3 4 5 6 7 8
910111214 13 Figure 2.- Front panel.
[1] LCD Display. TFT Color display, 640x480 resolution. [2] F1-F6. Soft keys linked to the menu that appears on the
right side of the display. [3] Main Keys. Including Frequency, Span and Amplitude the most
popular keys.. [4] Measurement keys. Measurement groups including Marker, Peak
Search, Trace, Power Measurement and Limit Line.
USER’S MANUAL AE-966 / 967
Page 32 02/2007
[5] Control keys. Control function groups including BW, Trigger,
Display and Save/Recall, the BW inluding RBW, VBW and Sweep Time.
[6] State keys Groups of functions of condition that include
Preset, System, Options and Sequences. The function Options defines the condition of all the options.
[7] ON/STBY key. ON/STBY key selects the condition of
functioning of the equipment: extinguished in way "It" "Waits" for (red flushed indicator), ignited (green flushed indicator). To activate / deactivate the general nourishment of the equipment, there uses the switch placed in the later panel.
[8] Arrow Key. Arrow key selects parameters in various
occasions; Up/Right for increasing, Down/Left for decreasing.
[9] Scroll Knob Scroll knob sets or selects parameters in
various occasions. In some cases, it works in tandem with the Arrow key.
[10] RF input. Input terminal accepts RF input signal.
Maximum +30dBm, 50Ω. [11] Pre-Amplifier Power Pre-Amplifier power supply terminal provides
power for the optional pre-amplifier. [12] Numerical Keys. Numerical keys set various parameters. In
some cases, they work in tandem with the Arrow key / Scroll knob.
[13] TG Output Terminal. Outputs the optional Tracking Generator signal.
Reversed power should not exceed +30dBm. [14] USB Output Connector USB host, typeA, male connector saves /
recalls data and prints out display image.
USER’S MANUAL AE-966 / 967
02/2007 Page 33
Eng
lish
6.1.2 Rear Panel description.
RS-232
PHONE
GPIB
VGA
FREQADJUST
REF INPUT
10 MhzREF OUTPUT
EXT TRIG.INPUT
DC 12V INPUT
40 W MAX.
15 16 17 18 19 20 21 22
232425262728
Figure 3.- Rear Panel.
[15] FREC. ADJUST. Adjusts the internal reference signal frequency; for service operation only.
[16] GBIP Optional 24 pin female GPIB connector for
remote control. [17] Conector USB Type B mini connector for PC software
connection and remote control. [18] RS232 9 pin female connector for PC software
connection and remote control. [19] Headphone (Optional) 3.5mm phone jack for audio output. Available
when the optional Demodulator is installed. [20] Battery Pack (Optional) Optional battery pack for portable usage.
Installed together with DC operation module. [21] Main Power Switch The main switch for turning On/Off the power. [22] Fuse Socket Stores rating fuse. [23] AC Input Power supply input.
USER’S MANUAL AE-966 / 967
Page 34 02/2007
[24] DC Input Input 12 V DC. [25] VGA Output 15pin, female VGA connector that outputs 640
x 480 resolution display image to an external monitor.
[26] Trigger Input Accepts a trigger signal from an external
device. [27] 10 MHz Ref Output Outputs +5V TTL, 10MHz reference signal used
for synchronizing AE-967 with external device. [28] REF INPUT Accepts a signal from an external device, used
for synchronization with AE-966-967.
USER’S MANUAL AE-966 / 967
02/2007 Page 35
Eng
lish
6.3 Main functions.
6.3.1 Frequency/Span functions.
Frequency key, together with Span key, sets the frequency scale. Two methods are available. Center-and-Span method defines the center point and the surrounding frequency range. Start-and-Stop method defines the beginning and the end of the frequency range. Special span settings are available at full/zero span. You can also recall the last span setting.
6.3.1.1 View Signal (Center and Span).
Center-and-Span method defines the Center frequency and the left/right bandwidth (Span) to locate the signal.
• Set frequency adjustment step
Background Frequency adjustment step defines the Arrow key resolution for Center, Start, and Stop frequency.
1.- Press the Frequency key.
Frequency
2.- Press F4 (Step). Step0 kHz F 4
Panel operation
3.- Enter the value using the numerical keys, Arrow key, and Scroll knob.
µ
Range 0.0kHz ~ 3.0GHz * Arrow key and Scroll knob resolution: 1/10 of Span.
USER’S MANUAL AE-966 / 967
Page 36 02/2007
• Set Center Frequency
1.- Press the Frequency key. Frequency
2.- Press F1 (Center). Center
1.5 GHz F 1
Panel operation
3.- Enter the value using the numerical keys, Arrow key, and Scroll knob.
µ
Range 0,0kHz ~ 3,0GHz * Arrow key and Scroll knob resolution: step value.
Note Center frequency/span automatically changes according to start/stop frequencies setting, and vice versa.
Display
Center
Frequency reading
• Set Frequency Span
1.- Press the Span key. Span
2.- Press F1 (Span). Span
3 GHz F 1
Panel operation
3.- Enter the value using the numerical keys, Arrow key, and Scroll knob.
µ
Range 2 kHz ~ 3 GHz * Arrow key & Scroll knob resolution: 1-2-5 sequence (0 [zero span], 2 kHz, 5 kHz, 10 kHz, 20 kHz, 50 kHz..... 1GHz, 2GHz, 3GHz)
USER’S MANUAL AE-966 / 967
02/2007 Page 37
Eng
lish
Note Center frequency/span automatically changes according to start/stop
frequency settings, and vice versa. Display
Span
Span reading
6.3.1.2 View Signal (Start and Stop)
Start-and-Stop method defines the beginning (Start) and the end (Stop) of the frequency range. • Set frequency adjustment Step Background Frequency adjustment step defines the Arrow
key resolution for Center, Start, and Stop frequency.
1.- Press the Frequency key.
Frequency
2.- Press F4 (Step). Step0 kHz F 4
Panel operation
3.- Enter the value using the numerical keys, Arrow key, and Scroll knob.
µ
Range 0.0kHz ~ 3.0GHz * Arrow key and Scroll knob resolution: 1/10 of Span.
USER’S MANUAL AE-966 / 967
Page 38 02/2007
• Set Start frequency.
1.- Press the Frequency key.. Frequency
2.- Press F2 (Start). Start
0 kHz F 2
Panel operation
3.- Enter the value using the numerical keys, Arrow key, and Scroll knob.
µ
Range 0,0kHz ~ 3,0GHz (Start Frequency ≤ Stop Frequency) * Arrow key and Scroll knob resolution: Step value.
Note Center frequency/span automatically change according to start/stop frequency settings, and vice versa.
Display
Start Frequency
Frequency reading
• Set Stop frequency
1.- Press the Frequency key. Frequency
2.- Press F3 (Stop). Stop
3 GHz F 3
Panel operation
3.- Enter the value using the numerical keys, Arrow key, and Scroll knob.
µ
Range 0,0kHz ~ 3,0GHz (Start Frequency ≤ Stop Frequency) * Arrow key resolution: Step value * Scroll knob resolution: 1/500 of Span
USER’S MANUAL AE-966 / 967
02/2007 Page 39
Eng
lish
Note Center frequency/span automatically change according to start/stop
frequency settings, and vice versa. Display
Frequency reading
Stop Frequency
6.3.1.3 Full/Zero Span
Full or Zero Span sets the span to extreme values: 3.0GHz (full) or 0kHz (zero). They provide faster ways to view signals in certain situations, such as in time domain (zero span) for viewing modulation or in full span for viewing frequency unknown signal. • Display Full Frequency Span (3.0GHz)
1.- Press the Span key.. Span
Panel operation
2.- Press F2 (Full Span). Full Span F 2
Range 3.0 GHz (fixed).
Full span also sets these parameters to fixed values.
- Center Frequency 1.5GHz - Start frequency: 0.0kHz - Stop frequency: 3.0GHz
USER’S MANUAL AE-966 / 967
Page 40 02/2007
Display
Full Span
3.0GHz reading
• Display Zero Span (time domain view)
1.- Press the Span key. Span
Panel operation
2.- Press F3 (Zero Span). Zero Span F 3
Range Center frequency (fixed)
Zero span also sets these parameters to fixed values.
- Start frequency: same as the Center frequency. - Stop frequency: same as the Center frequency
Note Make sure the RBW setting is large enough when using Zero Span for
viewing amplitude modulation.
USER’S MANUAL AE-966 / 967
02/2007 Page 41
Eng
lish
Display The diagram shows an example of observing the amplitude
modulation of the input signal.
Amplitude modulation
0kHz Span
Start=Center=Stop frequency
• Recall the Last Span Setting
1.- Press the Span key. Span
2.- Press F4 (Last Span).
Last Span F 4
Panel operation
3.- The span setting goes back to the previous one. Nesting level 1 level
USER’S MANUAL AE-966 / 967
Page 42 02/2007
6.3.2 Amplitude
Amplitude key sets the vertical scale of the display, including the upper limit (Reference Level), vertical range/unit (Amplitude Scale and Unit), and compensation for external gain or loss (External Offset). Amplitude Correction adjusts the frequency response distortion caused by external networks. Pre-Amplifier is an optional item that boosts the level of weak input signal before entering GSP-830. You can also set input impedance level according to the application needs.
6.3.2.1 Set Vertical Scale.
Vertical display scale is defined by the reference amplitude level, vertical amplitude range, measurement unit, and external gain/loss setting. • Set reference amplitude level
The reference level defines the uppermost display level.
1.- Press the Amplitude key. Amplitude
2.- Press F2 (Start). Ref.Level
-30.0dBm F 1
Panel operation
3.- Enter the value using the numerical keys, Arrow key, and Scroll knob.
µ
Range dBm -110 ~ +20 dBm, 0.1dB resolution.
dBmV -63.01 ~ +66.99 dBmV, 0.01dB resolution.
dBµV -3.01 ~ +126.99 dBuV, 0.01dB resolution
USER’S MANUAL AE-966 / 967
02/2007 Page 43
Eng
lish
Display Reference Level Reading
Reference level
• Select Amplitude scale
1.- Press the Amplitude key. Amplitude
Panel operation
2.- Press F2 (Scale dB/Div) repeatedly to select the scale.
Scale dB/Div10 5 2 1 F 2
Range 10, 5, 2, 1 dB/Div
Display Scale reading
USER’S MANUAL AE-966 / 967
Page 44 02/2007
• Select Amplitude Unit
1.- Press the Amplitude key. Amplitude
2.- Press F3 (Units).
Units... F 3
3.- Select and press the unit from F1 (dBm), F2 (dBmV), and F3 (dBuV). dBm F 1
dBmV F 2
dBuV F 3
Panel operation
4.- Press F6 (Return) to go back to the previous menu. Return F 6
Range dBm -110 ~ +20 dBm
dBmV -63.01 ~ +26.99 dBmV
dBµV -3.01 ~ +126.99 dBµV • Set External Offset level
External offset compensates amplitude gain or loss caused by an external network or device.
1.- Press the Amplitude key. Amplitude
2.- Press F4 (Ext.Gain). Ext.Gain
0dB F 4
Panel operation
3.- Enter the value using the numerical keys
µ
Range -20.0dB ~ +20.0dB, 0.1dB resolution
Icon
Amplitude icon appears at the bottom of the display
when the external offset level is changed.
USER’S MANUAL AE-966 / 967
02/2007 Page 45
Eng
lish
Example 1.-Before (Offset: 0dB)
Offset:-3dB
Reference: -30dBm
Icon 2.-Después (After (Offset: -3dB)
6.3.2.2 Amplitude Correction
Amplitude correction adjusts frequency response by changing amplitude for specific frequencies.
USER’S MANUAL AE-966 / 967
Page 46 02/2007
Menu tree
Corrections.. F 5
Select1 2 3 4 5 F 1
Delete F 2
Delete All.. F 3
Undelete F 4
Return F 6
Edit... F 1
CorrectionOn Off F 2
Return F 6
No F 1
Yes F 2
Return F 6
Amplitude
Save Now F 5
Correction set 5 set, 30 correction points each
Amplitude -40 ~ +40dB per correction point, 0.1dB resolution
Range
Frequency 9 kHz ~ 3.0GHz, 1kHz resolution
Icon
Amplitude icon appears at the bottom of the display when
amplitude correction is On. • Correct amplitude step by step Example description
In this example, the network between distorts the waveform and pushes
the level down at around 2.4GHz. Amplitude correction can fix the level.
In this example the amplitude around 2.4GHz is boosted by +1 ~ +3dB. Correction level
2.2GHz +2.5dB
2.3GHz +1.3dB
2.4GHz +2.8dB
2.5GHz +2.5dB
2.6GHz +1.2dB
USER’S MANUAL AE-966 / 967
02/2007 Page 47
Eng
lish
Diagram
Waveform (before correction)
The frequency response is distorted (non-flat) and the level is
attenuated by 2 ~ 3dB
1.- Press the Amplitude key.. Amplitude
2.- Press F5 (Corrections). Corrections.. F 5
1. Enter correction edit mode
3.- Press F1 (Edit). The display shows the
correction sets. Edit... F 1
USER’S MANUAL AE-966 / 967
Page 48 02/2007
2. Select correction set
Press F1 (Select) repeatedly to select the
correction set. 5 sets, 30 points each, are
selectable.
Select1 2 3 4 5 F 1
2. Select correction set
Example: correction set 3 selected.
Select1 2 3 4 5 F 1
1.- Make sure that the cursor is pointing to
the first empty frequency point.
Pt. Freq. (MHz) Gain12345
2.- If necessary, move the cursor using the
Up/Down key. 3.- Enter the frequency in MHz using the
numerical keys.
9.0 kHz ~ 3.0GHz.
µ
3a. Add correction point
4.- The cursor automatically moves to the
Gain side.
Enter the gain in dB using the numerical
keys.
-40dB ~ +40dB.
Pt. Freq. (MHz) Gain12345
2200
µ
5.- Repeat the above procedure for all correction data. The points are
automatically sorted by the frequency (low → high).
USER’S MANUAL AE-966 / 967
02/2007 Page 49
Eng
lish
3b. Modify
correction
point
1.- Move the cursor using the
Arrow key. 2.- Enter the new frequency or
gain using the numerical keys.
Pt. Freq. (MHz) Gain12345
23002.5
240025002600
22001.32.81.81.2
µ
1. Move the cursor to the target
using the Arrow key. 2.- Press F2 (Delete). The
frequency and gain are
deleted together.
Delete F 2
3.- To undo the last deletion, press
F4 (Undelete). Undelete F 4
3c. Delete
correction
point
Example: point 3 deleted. Pt. Freq. (MHz) Gain
12345
23002.5
240025002600
22001.32.81.81.2
Pt. Freq. (MHz) Gain12345
23002.5
25002600
22001.31.81.2
1.- Press F5 (Save Now). The
edited data is saved internally. Save Now F 5
4. Save
correction
set 2.- Press F6 (Return) to go back to
the previous menu. Return F 6
USER’S MANUAL AE-966 / 967
Page 50 02/2007
1.- Press F2 (Correction On) to
turn On the correction.
CorrectionOn Off F 2
5. Activate
correction
2.- The amplitude icon appears at
the bottom of the display. After
correction
Frequency response becomes linear (original), and the gain is
compensated by +2 ~ +3dB.
• Delete entire correction set data
1.- Press the Amplitude key.. Amplitude
2.- Press F5 (Corrections).
Corrections.. F 5
3.- Press F1 (Edit). The display shows the correction sets. Edit... F 1
4.- Press F1 (Select) repeatedly to select the
correction set. Select
1 2 3 4 5 F 1
Panel operation
5.- Press F3 (Delete All). Delete All.. F 3
USER’S MANUAL AE-966 / 967
02/2007 Page 51
Eng
lish
6.- Select and press F1 (No) or F2 (Yes) for
confirm. The whole data in the specified correction set is deleted.
No F 1
Yes F 2
7. Press F6 (Return) repeatedly to go back to previous menus.
Return F 6
• Recall existing correction set
1.- Press the Amplitude key.. Amplitude
2.- Press F5 (Corrections).
Corrections.. F 5
3.- Press F1 (Edit). The display shows the correction sets. Edit... F 1
4.- Press F1 (Select) repeatedly to select the
correction set. Select
1 2 3 4 5 F 1
5.- Press F6 (Return) to go back to the previous menu. Return F 6
Panel operation
6.- Press F2 (Correction ON) to activate the correction.
CorrectionOn Off F 2
• Save/copy/delete/rename correction file Background Correction files can be saved, copied,
deleted, or renamed using the file utility. Press the File key to access each function.
File
Save/Copy Press F1 (Copy). Copy... F 1
Delete Press F2 (Delete).
Delete... F 2
Rename Press F3 (Rename). Rename... F 3
USER’S MANUAL AE-966 / 967
Page 52 02/2007
6.3.2.3 Set Input Impedance • Select input impedance (50 Ω / 75 Ω) Background In most cases, the default 50 is appropriate. Use 75 when
specifically required, such as in Cable TV signals.
1.- Press the Amplitude key. Amplitude
2.- Press F6 (More).
More F 6
3.- Press F1 (InputZ 50 Ω / 75 Ω) to select the impedance.
InputZ50Ω 75Ω F 1
Panel operation
4.- When 75Ω is selected, the amplitude icon appears at the bottom of the display.
• Set impedance offset (75Ω only) Background Impedance transformation to 75 Ω is also available through external
devices such as impedance converter module. In these cases an external loss will be induced. The impedance offset can compensate this effect.
1.- Press the Amplitude key. Amplitude
2.- Press F6 (More).
More F 6
3.- Make sure 75Ω is selected in F1 (Input Z).. InputZ50Ω 75Ω F 1
4.- Press F2 (Input Z Cal). Input Z Cal5.9dB F 2
Panel operation
5.- Enter the offset using the numerical keys.
µ
Range - 10dB ~ + 10dB, 0,1dB resolution.
USER’S MANUAL AE-966 / 967
02/2007 Page 53
Eng
lish
6.3.3 Autoset
Autoset function checks the input signal configuration and automatically setup the suitable horizontal and vertical scale. The amplitude floor for limiting the search range, and frequency observation span for limiting the viewing range are customizable according to the application needs.
6.3.3.1 Run Autoset (search full amplitude range)
1.- Press the Autoset key Autoset
Panel operation
2.- Press F1 (Autoset). Autoset F 1
Search range
Amplitude dBm -80 ~ +20 dBm
dBmV -33.01 ~ + 66.99 dBmV
dBµV +26.99 ~ + 126.99 dBµV
Frequency 0kHz ~ 3.0GHz
* These ranges are applicable when both Amplitude floor (F2) and Span
limit (F3) are set to Auto. Example: before Autoset
Start frequency: 0kHz Stop frequency: 3GHz
Span: 3GHz Signal peak: 100MHz
Center frequency: 1.5GHz Reference level: -10dBm
USER’S MANUAL AE-966 / 967
Page 54 02/2007
Start frequency: 97.5MHz Stop frequency: 102.5MHz
Span: 5MHz Signal peak: 100MHz
Center frequency: 100MHz Reference level: -30dBm
Example: after
Autoset
RBW/VBW/Sweep
Setting after
Autoset
All the three BW related parameters, RBW, VBW, and Sweep, will
be reset to Auto mode when using Autoset, regardless of their
previous settings
USER’S MANUAL AE-966 / 967
02/2007 Page 55
Eng
lish
• Limit vertical search range Background You can set the amplitude floor so that the signals lower than the
setting will be ignored from Autoset search.
1.- Press the Autoset key. Autoset
2.- Press F2 (Amp. Floor) to switch the range
from Auto (whole range) to manual (limited range).
Amp.FloorAuto Man F 2
Panel operation
3.- Enter the amplitude in dB, using the numerical keys. The Command window shows the setting.
µ
Amp. : -30dBm
Range dBm -80 ~ +20dBm, 0.1dB resolution.
dBmV -33.01 ~ +66.99dBmV, 0.01dB resolution.
dBµV +26.99 ~ +126.99dBµV, 0.01dB resolution.
• Limit horizontal view range Background You can change the frequency span limit in the display to get a better
view of the Autoset result. By default, the frequency span after Autoset is set at 5MHz (Auto).
1.- Press the Autoset key. Autoset
2.- Press F3 (Span) to switch the range
between Auto (5MHz fixed limit) to Manual.
SpanAuto Man F 3
Panel operation
3.- Enter the frequency using the numerical keys. The Command window shows the setting.
µ
Span : 10MHz
Range Zero span, 2 kHz ~ 3GHz (Manual) 5 MHz fixed (Auto)
USER’S MANUAL AE-966 / 967
Page 56 02/2007
6.3.4 Marker
A Marker shows the frequency and amplitude of a waveform point. GSP-830 can activate up to 5 Markers or Marker pairs simultaneously. Marker Table helps editing and viewing multiple Markers in a single display. You can also enable/disable all Markers at once. Delta Marker shows the frequency and amplitude difference between the reference Marker. GSP-830 can automatically move the Marker to various locations including peak signal, center frequency, and start/stop frequency. More Marker operations regarding signal peaks are also available in the Peak Search function.
USER’S MANUAL AE-966 / 967
02/2007 Page 57
Eng
lish
6.3.4.1 Activate/de-activate marker(s) Menu tree F3 ~ F5 are available only when the Marker is On (activated).
More F 6
Marker1 2 3 4 5 F 1
On Off F 2
ModeNormal ∆Mkr F 3
To Peak F 4
Mkr Center F 5
All MkrsOn Off F 3
Marker
Range Normal marker: 5
Delta marker: 5 pairs
Amplitude: -120 ~ +20dBm, 0.1dB resolution.
-73.01 ~ + 66.99dBmV, 0.01dB resolution.
-13.01 ~ + 126.99dBuV, 0.01dB resolution.
Frequency: 0kHz ~ 3.0GHz
• Activate normal marker(s)
1.- Press the Marker key. Marker
2.- Press F1 (Marker) repeatedly to select the
marker ID from 1 to 5. Marker
1 2 3 4 5 F 1
3.- Press F2 (ON) and turn On the selected marker. On Off F 2
4.- Make sure Normal is selected in F3. If
necessary, press and select Normal. Mode
Normal ∆Mkr F 3
Panel operation
5.- Repeat the above steps for the number of markers required.
USER’S MANUAL AE-966 / 967
Page 58 02/2007
Display The upper right corner of the display shows the active marker.
Número de Marcador , Frecuencia , Amplitud
• Activate all 5 normal markers at once
1.- Press the Marker key.. Marker
2.- Press F6 (More)
More F 6
3.- Press F3 (All Mkrs On) to turn On all 5 normal markers.
All MkrsOn Off F 3
Panel operation
4.- To view all marker status, press F2 (Marker Table On). The frequency and the amplitude of the markers appear in table list.
Marker TableOn Off F 2
USER’S MANUAL AE-966 / 967
02/2007 Page 59
Eng
lish
Display The upper right corner of the display shows the active marker status.
• Activate delta marker(s)
1.- Press the Marker key. Marker
2.- Press F1 (Marker) repeatedly to select the
marker ID from 1 to 5. Marker
1 2 3 4 5 F 1
3.- Press F2 (On) and turn On the selected marker. On Off F 2
4.- Make sure ∆ (delta) is selected in F3. If
necessary, press and select ∆ Mkr. Mode
Normal ∆MkrF 3
Panel operation
5.- Repeat the above steps for the number of markers required.
USER’S MANUAL AE-966 / 967
Page 60 02/2007
Display The upper right corner of the display shows the active delta marker pair.
Marker ID, Frequency, Amplitude
6.3.4.2 Move marker
This section assumes at least one marker is already activated. Marker frequency positions can be set manually, or to specific locations using the menu shortcuts. • Move marker manually
1.- Check the active marker at the top right corner of the display.
Panel operation
2.- Move the marker using the Left/Right key and Scroll knob, or enter the frequency directly using the numerical keys.
µ
USER’S MANUAL AE-966 / 967
02/2007 Page 61
Eng
lish
• Move marker to the highest peak
1.- Check the active marker at the top right corner of the display.
2.- Press the Marker key.. Marker
Method 1
3.- Press F4 (To Peak). To Peak F 4
1.- Another method (the same effect) is to
press the Peak Search key. Peak Search Method 2
2.- Press F1 (Pk Search). Pk Search F 1
1.- Another method moves marker to the peak
and also tracks it. Press the Peak Search key.
Peak Search 2.- Press F6 (More).
More F 6
3.- Press F4 and Turn On the Track TrackOn Off F 4
Method 3
4.- The peak tracking icon appears at the bottom of the display.
• Move marker and the highest peak to the center
1.- Check the active marker at the top right corner of the display.
2.- Press the Marker key. Marker
3.- Press F4 (To Peak). The marker moves to
the signal peak. To Peak F 4
Method 1
4.- Press F5 (Mkr→Center). The signal peak moves to the center. Mkr Center F 5
USER’S MANUAL AE-966 / 967
Page 62 02/2007
1.- Another method (the same effect) is to
press the Peak Search key.. Peak Search Method 2
2.- Press F5 (Mkr→Center) to find out the signal peak, then to move it to the center. Mkr Center F 5
• Move marker to various locations
1.- Check the active marker at the top right corner of the display.
2.- Press the Marker key. Marker
3.- Press F6 (More).
More F 6
4.- Press F4 (Mkr to ...) Mkr to... F 4
5.- Select the destination and press F1
(Center) ~ F5 (Ref Lvl). Center: center frequency Start: start frequency Stop: stop frequency CF Step: set the marker frequency as the
frequency step value Ref Lvl: reference amplitude level.
Mkr Center F 1
Mkr Start F 2
Mkr Stop F 3
Mkr CFStep F 4
Mkr Ref Lvl F 5
Panel operation
6.- Press F6 (Return) to go back to the previous menu. Return F 6
USER’S MANUAL AE-966 / 967
02/2007 Page 63
Eng
lish
• Move marker to a trace
1.- Check the active marker at the top right corner of the display
2.- Press the Marker key. Marker
3.- Press F6 (More).
More F 6
Panel operation
4.- Press F1 (Marker Trace). Marker TraceAuto A B C F 1
Range Auto The marker moves to the active signal/trace.
Trace A The marker moves to Trace A.
Trace B The marker moves to Trace B.
Trace C The marker moves to Trace C. 6.3.4.3 Show Markers in Table
1.- Check the active marker at the top right corner of the display.
2.- Press the Marker key. Marker
3.- Press F6 (More).
More F 6
4.- Press F2 (Marker Table On). Marker TableOn Off F 2
Panel operation
5.- The marker ID, frequency, and amplitude list appears at the lower half
of the display, updated in real time. Display
USER’S MANUAL AE-966 / 967
Page 64 02/2007
6.3.5 Peak Search
Peak search automatically finds out the signal peaks in various conditions, such as next highest peak and minimum peak. Peak Search overlaps its feature with Marker function, and it is best to use the two together. All peaks can be viewed at once in the peak table, with amplitude threshold and sorting order configurable.
6.3.5.1 Search Signal Peaks
Peak Search puts a marker on the target signal peak. If no marker has been activated, GSP-830 automatically activates marker 1. The peak signal frequency and amplitude appear at the top right corner of the display.
Marker ID, Frequency, Amplitude
USER’S MANUAL AE-966 / 967
02/2007 Page 65
Eng
lish
• Search signal peak
1.- Press the Peak Search key. Peak Search
Method 1
2.- Press F1 (Pk Search). Pk Search F 1
1.- Another method is to use the Marker key. Make sure the marker is
already activated 2.- Press the Marker key.
Marker
Method 2
3.- Press F4 (To Peak). To Peak F 4
1.- Another method continuously tracks the
peak signal. Press the Peak Search key. Peak Search 2.- Press F6 (More). More F 6
3.- Press F4 (Track On). TrackOn Off F 4
Method 3 (marker tracked to the peak)
4.- The peak tracking icon appears at the
bottom of the display.
USER’S MANUAL AE-966 / 967
Page 66 02/2007
• Search the next highest peak
The marker keeps moving to the next highest peak, in descending order.
1.- Press the Peak Search key.. Peak Search
Panel operation
2.- Press F2 ~ F4 repeatedly. Next Peak: moves the marker to the next
highest peak. Next Pk Right: moves the marker to the next
highest peak on the right side (higher frequency).
Next Pk Left: moves the marker to the next highest peak on the left side (lower frequency)
Next Peak F 2
Next PkRight F 3
Next Pk Left F 4
Display
• Search the highest peak and move to the center
1.- Press the Peak Search key Peak Search
Method 1
2.- Press F1 (Pk Search). Pk Search F 1
Method 2 1.- Another method (the same effect) is to press the Marker key. Make
sure the marker is already activated
USER’S MANUAL AE-966 / 967
02/2007 Page 67
Eng
lish
2.- Press the Marker key.
Marker
3.- Press F4 (To Peak). To Peak F 4
Method 2
4.- Press F5 (Mkr→Center). Mkr Center F 5
• Search the minimum amplitude
1.- Press the Peak Search key. Peak Search
2.- Press F6 (More). More F 6
Panel operation
3.- Press F5 (Min Search). The active marker
moves to the deepest valley in the trace. Min Search F 5
Display
Minimum Amplitude
USER’S MANUAL AE-966 / 967
Page 68 02/2007
6.3.5.2 Show Peak Table • Activate peak table
1.- Press the Peak Search key.. Peak Search
2.- Press F6 (More). More F 6
Panel operation
3.- Press F1 (Peak Table On). Peak TableOn Off F 1
Display
Range 10 peaks maximum.
USER’S MANUAL AE-966 / 967
02/2007 Page 69
Eng
lish
• Set peak threshold
Only the peaks below the threshold amplitude will be listed in the table.
1.- Press the Peak Search key. Peak Search
2.- Press F6 (More). More F 6
3.- Press F1 (Peak Table On). Peak Table
On Off F 1
4.- Press F3 (Peak Threshold On). Pk ThresholdOn Off F 3
5.- A horizontal line appears on the display. Searches and lists peaks only
below this threshold amplitude.
Panel operation
6.- Use the Arrow key or the Scroll knob to
move the threshold line.
6.3.5.3 Sort peaks
The peaks are sorted in order of ascending frequency / descending amplitude.
1.- Press the Peak Search key. Peak Search
2.- Press F6 (More). More F 6
Panel operation
3.- Press F2 (Peak Sort) ) to switch between
frequency and amplitude sorting.
Peak SortFreq Amp F 2
USER’S MANUAL AE-966 / 967
Page 70 02/2007
Example: amplitude sort
6.3.6 Trace
Trace keeps track of waveform variants. Three traces, A, B, and C, are available for accumulating the peak level, freezing the current waveform shape, and averaging the waveform. Trace math operations are available using trace A and B.
Detection modes configure the way GSP-830 samples the input analog signal for digitizing.
USER’S MANUAL AE-966 / 967
02/2007 Page 71
Eng
lish
6.3.6.1 View traced waveform • Select (activate) trace
1.- Press the Trace key. Trace
Panel operation
2.- Press F1 (Trace) repeatedly to select the trace
TraceA B C F 1
Range A (green) The default trace which is always activated. Together
with trace B, runs trace math operation.
B (amber) Together with trace A, runs trace math operation.
C (yellow) • View real-time updated trace (default) Background The trace is updated at every sweep. Old trace is cleared up and a
new trace according to the latest measurement is drawn on the
display. 1.- Press the Trace key.
Trace 2.- Press F2 (Clear).
Clear F 2
Panel operation
3.- The clear mode icon appears at the bottom of the display.
USER’S MANUAL AE-966 / 967
Page 72 02/2007
• View peak-hold trace Background In peak hold mode, the amplitude of the new trace is compared with
the last one at each sweep. Only the higher amplitude replaces old
trace points, thus holding the highest (peak) value. 1.- Press the Trace key.
Trace 2.- Press F3 (Peak Hold).
Peak Hold F 3
Panel operation
3.- The peak hold mode icon appears at the bottom of the display.
Display
Peak Hold
Clear (default)
• Freeze trace
1.- Press the Trace key. Trace
2.- Press F4 (View). View F 4
Panel operation
3.- The view mode (freeze) icon appears at the bottom of the display.
USER’S MANUAL AE-966 / 967
02/2007 Page 73
Eng
lish
• Hide trace
1.- Press the Trace key.. Trace
2.- Press F5 (Blank). Blank F 5
Panel operation
3.- The trace disappears from the display. To bring back the trace again, press F2 (Clear).
Clear F 2 • View averaged trace
1.- Press the Trace key. Trace
2.- Press F6 (More). More F 6
3.- Press F1 (AVG On) to turn On the
average mode AVG
On Off 20
F 1 4.- The average mode icon appears at the
bottom of the display.
Panel operation (Method 1)
5.- Enter the average number using the numerical keys.
µ
1.- Press the BW key..
BW
2.- Press F4 (AVG On) to turn On averaging. AVGOn Off
20 F 4
Method 2
3.- Enter the average time using the numerical keys.
µ
Range 1 ~ 100
USER’S MANUAL AE-966 / 967
Page 74 02/2007
Example: after average
Averaged 20 times
6.3.6.2 Move Marker to Trace
1.- Check the active marker at the top right corner of the display.
2.- Press the Marker key.. Marker
3.- Press F6 (More)
More F 6
Panel operation
4.- Press F1 (Marker Trace). Marker TraceAuto A B C F 1
Range Auto The marker moves to the active signal or trace.
Trace A The marker moves to Trace A.
Trace B The marker moves to Trace B.
Trace C The marker moves to Trace C.
USER’S MANUAL AE-966 / 967
02/2007 Page 75
Eng
lish
Display Marker on Trace C
• Save/copy/delete/rename trace file Background Trace files can be saved, copied, deleted,
or renamed using the file utility. Press the File key to access each function.
File
Save/Copy Press F1 (Copy). Copy... F 1
Delete Press F2 (Delete).
Delete... F 2 Rename Press F3 (Rename).
Rename... F 3
USER’S MANUAL AE-966 / 967
Page 76 02/2007
6.3.6.3 Run Trace Math Background You can run various mathematical operations between TraceA and
TraceB. Both traces have to be activated in advance. After the math
operation, the traces mode changes into View. 1.- Press the Trace key.
Trace 2.- Press F6 (More).
More F 6 3.- Press F2 (Trace Math).
Trace Math.. F 2
4.- Select and press the type of math operation from F1 ~ F5.
A↔B: swaps trace A and B.. A+B→A: Adds trace A and B A-B→A: Subtracts trace B from trace A. A+const→A: Adds a constant value to trace
A A-const→A: Subtracts a constant value from
trace A.
A B F 1
A+B A F 2
A-B A F 3
A+const A F 4
A-const A F 5 5.- When A+const / A- const are selected,
enter the constant value using the numerical keys
Range: -40 ~ +40dB
µ
Panel operation
6.- The trace math icon appears at the bottom of the display.
USER’S MANUAL AE-966 / 967
02/2007 Page 77
Eng
lish
Example:
A↔B
Example:
A+B→A
Example:
A-B→A
USER’S MANUAL AE-966 / 967
Page 78 02/2007
Example:
A+Constante → A (5 dB)
Example:
A-Constante → A (5 dB)
6.3.6.4 Select Signal Detection Mode Background In order to show the incoming signal on the display, GSP-830 first
converts the input signal to a video signal, digitizes it, then use a
detector to pick up the samples to be displayed. By configuring the
detection mode, certain signals can be viewed more clearly/sharply. 1.- Press the Trace key. Trace
Panel operation
2.- Press F6 (More). More F 6
USER’S MANUAL AE-966 / 967
02/2007 Page 79
Eng
lish
3.- Press F3 (Detection). Detection.. F 3
4.- Select the signal detection type from F1 ~
F5 and press it. See below for description of
each type.
Normal F 1
Sample F 2
Peak+ F 3
AVG F 4
QPeak F 5
4.- Press F6 (Return) para volver al menú
anterior. Return F 6
Parameter Normal The default mode. When the signal level is
constantly increasing or decreasing detects the
positive peaks. Otherwise, detecting mode
switches between positive peak and negative
peaks. Useful for picking up burst phenomenon
while avoiding too much noise.
Sample Detects signals randomly. Useful when detecting
noise-like signals, but tend to miss burst
phenomenon.
Peak + Detects positive peak signals. Useful for
(positive peak) detecting sinusoid signal, but tend to pick up more
noise than other modes.
AVG (average) Available when the optional EMI filter is installed.
Detects the average power level of the samples,
using low pass filter. Useful for reducing the noise
level. For EMI filter details.
Qpeak
(quasi-peak) Available when the optional EMI filter is installed.
Detects the quasi-peak power level of the
samples. Useful for viewing in zero span without
missing signal variations. For EMI filter details.
USER’S MANUAL AE-966 / 967
Page 80 02/2007
Example Normal detection mode
Sample detection mode
Peak+ detection mode
USER’S MANUAL AE-966 / 967
02/2007 Page 81
Eng
lish
6.3.7 Power Measurement
Power Measurement function includes four types of frequently used complex measurement items: ACPR, OCBW, N dB, and Phase Jitter. Each item is configurable and updated in real-time.
6.3.7.1 Medida ACPR
• Description Background ACPR (Adjacent Channel Power Ratio), or ACLR (Adjacent Channel
Leakage Ratio) in other term, refers to the amount of leakage power
coming from the main radio channel which affects adjacent channels
as signal distortion. Menu tree
ACPROn Off F 2
CH Up F 4
CH Down F 5
ChannelSetup... F 1 CH BW F 1
CH SPC F 2
ADJ CHOffset... F 4
Adj CH BW1 F 1
Adj CH Offs1 F 2
Return F 6
Adj CH BW2 F 3
Adj CH Offs2 F 4
Meas
USER’S MANUAL AE-966 / 967
Page 82 02/2007
Parameter Channel bandwidth: The frequency bandwidth that the target
channel occupies. 1 kHz ~ 3.0GHz
Channel space: The frequency distance between each main
channel. 1 kHz ~ 3.0GHz
Adjacent channel bandwidth 1 & 2: The frequency bandwidth that
the adjacent channels 1 & 2 occupy. 1 kHz ~ 3.0GHz
Adjacent channel offset 1 & 2: The frequency distance between the
adjacent channel 1 & 2 and the main channel. 1 kHz ~ 3.0GHz 6.3.7.2 ACPR measurement step
1.- Press the Measurement key.. Meas 2.- Press F2 (ACPR On). ACPR
On Off F 2 3.- The display switches to ACPR mode, showing and updating ACPR
result on the lower half.
1. Activate ACPR
LowerACPR 1UpperACPR 1
LowerACPR 2
UpperACPR 2
USER’S MANUAL AE-966 / 967
02/2007 Page 83
Eng
lish
1.- Press F1 (Channel Setup). ChannelSetup... F 1
2.- Press F1 (CH BW). CH BW F 1 3.- Enter the channel BW using the numerical
keys, in MHz.
Range: 1 kHz ~ 3.0GHz
µ
2. Set channel BW
4.-The value is updated at the channel BW
column.
1.- Press F2 (CH SPC). CH SPC F 2
2.- Enter the channel space using the
numerical keys, in MHz.
Range: 1 kHz ~ 3.0GHz
µ
3. Set channel space
3.- The value is updated at the channel space
column. 1.- Press F4 (ADJ CH Offset). ADJ CH
Offset... F 4
2.- Press F1 (Adj CH BW1). Adj CH BW1 F 1 3.- Enter the adjacent channel 1 bandwidth
using the numerical keys
Range: 1 kHz ~ 3.0GHz
µ
4. Set adjacent channel1 bandwidth
4.- The value is updated at the Adj CH BW1
column.
1.- Press F2 (Adj CH Offs1) Adj CH Offs1 F 2
2.- Enter the adjacent channel 1 offset using
the numerical keys.
Range: 1 kHz ~ 3.0GHz
µ
5. Set adjacent channel1 offset
3.- The value is updated at the Adj CH
Offset1 column.
USER’S MANUAL AE-966 / 967
Page 84 02/2007
1.- Press F3 (Adj CH BW2). Adj CH BW2 F 3
2.- Enter the adjacent channel 2 bandwidth
using the numerical keys.
Range: 1 kHz ~ 3.0GHz
µ
6. Set adjacent channel2 bandwidth
3.- The value is updated at the Adj CH BW2
column. 1.- Press F4 (Adj CH Offs2). Adj CH Offs2 F 4
2.- Enter the adjacent channel 2 offset using
the numerical keys.
Range: 1 kHz ~ 3.0GHz
µ
7. Set adjacent channel2 offset
3.- The value is updated at the Adj CH
Offset2 column. 1.- Press F6 (Return) twice. Return F 6
x2
8. Move channel up/down
2.- Press F4 (CH Up) or F5 (CH Down) to
switch the measurement to the next channel. CH Up F 4
CH Down F 5
USER’S MANUAL AE-966 / 967
02/2007 Page 85
Eng
lish
6.3.7.3 OCBW Measurement • Overview Background OCBW (OCcupied BandWidth) refers to the bandwidth of the channel
that consumes (occupies) the specified amount of power. Menu tree
CH BW F 1
CH SPC F 2
CH Up F 4
CH Down F 5
ChannelSetup...
F 1
Return F 6
OCBWOn Off F 3 OCBW % F 3
Meas
Parameter Channel bandwidth: The frequency bandwidth that the target
channel occupies.
1 kHz ~ 3.0GHz, 1 kHz resolution.
Channel space The frequency distance between each main channel.
1 kHz ~ 3.0GHz, 1 kHz resolution.
OCBW % The ratio of occupied bandwidth as the amount of power
consumed.
0.0 % ~ el 100.0 %, 0.1 % resolution.
USER’S MANUAL AE-966 / 967
Page 86 02/2007
• OCBW measurement step
1.- Press the Measurement key. Meas 2.- Press F3 (OCBW On). OCBW
On Off F 3 3.- The display switches to OCBW mode, showing and updating OCBW
result on the lower half.
1. Activate OCBW
OCBW
CH Power
1.- Press F1 (Channel Setup). ChannelSetup... F 1
2.- Press F1 (CH BW). CH BW F 1 3.- Enter the channel BW using the numerical
keys, in MHz.
Range: 1 kHz ~ 3.0GHz
µ
2. Set channel BW
4.-BW column updates the value.
USER’S MANUAL AE-966 / 967
02/2007 Page 87
Eng
lish
1.- Press F2 (CH SPC). CH SPC F 2
2.- Enter the channel space using the
numerical keys, in MHz.
Range: 1 kHz ~ 3.0GHz
µ
3. Set channel space
3.- Space column updates the value.
1.- Press F3 (OCBW %). OCBW % F 3
2.- Enter the OCBW % using the numerical
keys and Enter key.
Range: 0,0 % ~ 100 %
µ
4. Set OCBW %
3.- OCBW % column updates the value.
1.- Press F6 (Return) twice. Return F 6
5. Move channel up/down
2.- Press F4 (CH Up) or F5 (CH Down) ) to
switch the measurement to the next channel. CH Up F 4
CH Down F 5 6.3.7.4 N dB Measurement Background N dB refers to the frequency bandwidth of a channel that covers the
specified amplitude. Parameter N dB : 0,1dB ~ 80,0dB, 0,1dB resolution.
1.- Press the Measurement key. Meas 2.- Press F6 (More). More F 6 3.- Press F1 (N dB BW On). N dB BW
On Off F 1
1. Activate N dB
4.- The display switches to N dB mode, showing and updating N dB
result on the lower half.
USER’S MANUAL AE-966 / 967
Page 88 02/2007
3dB Bandwidth
1.- Press F2 (N dB) to set the amplitude
which the BW covers. N dB F 2
2.- Enter the amplitude using the numerical
keys.
Range: 0.1dB ~ 70.0dB
µ
2. Set amplitude
3.- Press F1 (N dB BW On). N dB BWOn Off F 1
6.3.7.5 Phase Jitter Measurement. Background Phase Jitter refers to the amount of phase fluctuation that leads to
shortening or lengthening the Center frequency. Parameter Start offset: Beginning frequency offset in reference to the center
frequency.
0.0MHz ~ ½ of Span, 0.1MHz resolution.
Stop offset: End frequency offset in reference to the center
frequency.
0.0MHz ~ ½ de Span, 0.1MHz resolution. 1.- Press the Measurement key. Meas
1. Activate Phase Jitter
2.- Press F6 (More). More F 6
USER’S MANUAL AE-966 / 967
02/2007 Page 89
Eng
lish
3.- Press F3 (Phase Jitter On). Phase JitterOn Off F 3
4.- The display switches to Phase jitter mode, showing and updating
Phase jitter result on the lower half.
Phase fluctuationTime fluctuation
1.- Press F4 (Phase Jitter Setup) Phase JitterSetup F 4
2.- Press F1 (Start Offset) and F2 (Stop
Offset) to set the amount of beginning/end
offset.
StartOffset F 1
StopOffset F 2
2. Set start/stop offset
3.- Enter the offset using the numerical keys.
Range: 0,0MHz ~ ½ of Span
µ
USER’S MANUAL AE-966 / 967
Page 90 02/2007
6.3.8 Limit Line
Limit Line sets the upper and lower amplitude limit over the entire frequency range. The limit lines can be used to detect whether the input signal level is above, below, or within the target amplitude. The result, pass or fail, is shown at the display bottom in real-time.
6.3.8.1 Edit Limit Line Parameter Editing point: Maximum 10 points for each High and Low limit line.
Frequency: 9 kHz ~ 3.0GHz per editing point.
Amplitude: Per editing point:
-130 ~ +20dBm
-83.01dBmV ~ +66.99dBmV
-23.01dBuV ~ +126.99dBuV 1. Activate Limit Line
1.- Press the Limit Line key.
USER’S MANUAL AE-966 / 967
02/2007 Page 91
Eng
lish
2.- Press F1 (H Limit On) and/or F2 (L Limit
On) to activate the upper/lower limit line.
H LimitOn Off F 1
L LimitOn Off F 2
3.- The limit line appears on the display.
Blue: —— H limit line. (A)
Yellow: —— L limit line. (B)
H LimitLine (edited)
L LimitLine
1.- Press F3 (Edit). Edit... F 3
2.- Press F1 (Limit) to select the limit line to
be edited.
LimitLow High F 1
2. Activate limit line editing table
3.- Press F2 (Edit Table On). The editing
table appears on the bottom half of the
display.
Edit TableOn Off F 2
USER’S MANUAL AE-966 / 967
Page 92 02/2007
1.- Make sure that the cursor is pointing to the
first empty frequency point. Use the Up/Down
key to move the cursor, if necessary.
10 points are available for upper and lower
limit line each.
No. MHz dBm12345
2.- If necessary, move the cursor to different
frequency points using the Arrow key.
3.- Enter the frequency in MHz using the
numerical keys.
9.0 kHz ~ 3.0GHz.
µ
4.- The cursor automatically moves to the
Gain side. Enter the gain in dB using the
numerical keys.
Range: -130dB ~ +20dBm
No. MHz dBm12345
98
3a. Add a limit line point
5.- Continue the above steps for the points
needed.
USER’S MANUAL AE-966 / 967
02/2007 Page 93
Eng
lish
1.- Move the cursor to the deletion point using
the Arrow key.
2.- Press F3 (Delete) to delete the point
(frequency and amplitude together). Delete F 3
No. MHz dBm12345
100-40
102
98-30-40
No. MHz dBm12345
-4010298
-40
3b. Delete a limit line point
3.- To undo deletion, press F5 (Undelete). Undelete F 5
1.- Press F4 (Delete All). Delete All.. F 4
2.- Press F1 (No) or F2 (Yes) to confirm
deletion. All 10 limit line points will be deleted.No F 1
Yes F 2
3.- Press F6 (Return) to go back to the
previous menu. Return F 6
3c. Delete the whole limit line data
4.- To undo deletion, press F5 (Undelete). Undelete F 5
4. Switch upper/lower limit line
If necessary, press F1 (Limit) to start editing
the other limit line. Repeat the above steps.
LimitLow High F 1
Example Limit Line data (high) Point No. Frequency (MHz) Amplitude (dBm)
1 98MHz -40dBm
2 100MHz -30dBm
3 102MHz -40dBm
USER’S MANUAL AE-966 / 967
Page 94 02/2007
Resulted line
6.3.8.2 Run Pass/Fail test
This section assumes the limit line is already defined.
Checks whether all the waveform amplitude stays
between the high limit and low limit lines.
Checks whether the peak amplitude of the waveform
stays between the high and low limit lines.
Pass/Fail condition
Checks whether the minimum amplitude of the
waveform stays between the high and low limit lines.
1.- Press the Limit Line key. Limit Line 1. Select condition
2.- Press F5 (Pass/Fail) repeatedly to
select the condition.
Pass/Fail F 5
USER’S MANUAL AE-966 / 967
02/2007 Page 95
Eng
lish
1.- Press F4 (Pass/Fail On) to activate the
test.
Pass/FailOn Off F 4
2. Run Pass/Fail test
2.- The test result appears at the bottom of
the display. Display Result: failed
Note: If the high or low limit line is not defined, Pass/Fail test uses the highest or lowest
display level as limit line.
6.3.8.3 Save/copy/delete/rename limit line file Background Limit line files can be saved, copied,
deleted, or renamed using the file utility.
Press the File key to access each function.
File Save/Copy Press F1 (Copy). Copy... F 1
USER’S MANUAL AE-966 / 967
Page 96 02/2007
Delete Press F2 (Delete). Delete... F 2
Rename Press F3 (Rename). Rename... F 3
6.3.9 Bandwidth
BW (BandWidth) feature configures how narrow GSP-830 can sort out different signal peaks (resolution), and how fast the display can be updated (sweep time). Averaging the waveform is also available for smoothing noise level. The resolution and the sweep time (+averaging) are in a trade-off relationship, so configuration should be done with care.
6.3.9.1 Select RBW (Resolution BandWidth) Background RBW (Resolution Bandwidth) defines the width of the IF (intermediate
frequency) filter that is used to separate signal peaks from one
another. The narrower the RBW, the greater the capability to
separate signals at close frequencies. But it also makes the sweep
time longer under specific frequency span; the display is updated less
frequently. See for the reference to select the suitable RBW.
USER’S MANUAL AE-966 / 967
02/2007 Page 97
Eng
lish
1.- Press the BW key. BW
2.- Press F1 (RBW) to select Auto or Manual RBWAuto Manu F 1
3.- When Manu (manual) is selected, use the
Arrow key or Scroll knob to change it.
Panel operation
4.- The selected RBW appears in the
command window.
RBW: 30kHz
Mode Auto RBW is automatically set.
Manual RBW is manually selected. The BW icon appears at
the bottom of the display
Range RBW Recommended span Standard/ Optional
300 Hz Span <30 kHz Optional (300 Hz RBW)
3 kHz Span <300 kHz Standard
9 kHz 300kHz≤Span <600 kHz Optional (EMI Filter)
10 kHz 300kHz≤Span <1MHz Optional (10k/ 100kHz RBW)
30 kHz 300kHz≤Span <6MHz Standard
100 kHz 6MHz≤Span <20MHz Optional (10k/100kHz RBW)
120 kHz 6MHz≤Span <19MHz Optional (EMI Filter)
300 kHz 6MHz≤Span <60MHz Standard
4MHz 60MHz≤Span Standard 1.- Press the System key. System
2.- Press F6 (More). More... F 6
Check RBW installation status
3.- Press F4 (System Config On) to turn On
the system configuration window.
System ConfigOn Off F 4
USER’S MANUAL AE-966 / 967
Page 98 02/2007
Optional Items
4.- Check the optional items corner and see the RBW installation status
(checkmark — installed, blank — not installed).
Installed Not installed
5.- Press F4 (System Config Off) to close the
system configuration window. System ConfigOn Off F 4
Note: 9k/120kHz RBW (EMI Filter) and 10k/100kHz RBW are
exclusive; cannot be installed together. For a new RBW option install,
contact service personnel. 6.3.9.2 Select VBW (Video BandWidth) Background VBW (Video Bandwidth) defines the smoothness of the trace on the
display. Combined with RBW, Video BandWidth defines the ability to
sort out target signal from surrounding noise or adjacent peaks. 1.- Press the BW key. BW
2.- Press F2 (VBW) to select Auto or Manual VBW
Auto Manu F 2
Panel operation
3.- When Manu (manual) is selected, use the
Arrow key or Scroll knob to change it.
USER’S MANUAL AE-966 / 967
02/2007 Page 99
Eng
lish
4.- The selected VBW appears in the
command window.
VBW: 1kHz
Mode Auto: VBW is automatically set.
Manual: VBW is manually set. The VBW icon appears at the
bottom of the display.
Range VBW is automatically selected according to the RBW in Auto mode.
Use this for the reference when manually selecting the VBW. Note Automatically changes the VBW according to RBW selection
6.3.9.3 RBW/VBW Auto Mode Contents Background * The following applies when selecting Auto for RBW and VBW
setting. Use them as a reference when manually selecting the RBW
and VBW.
* The RBW/VBW range differs according to system configuration,
especially the optional item installation.
1.- Press the System key. System
2.- Press F6 (More). More... F 6
Check the RBW installation status
3.- Press F4 (System Config On) to turn
On the system configuration window
System ConfigOn Off F 4
USER’S MANUAL AE-966 / 967
Page 100 02/2007
Optional Items
4.- Press F4 (System Config Off) to close
the system configuration window.
System ConfigOn Off F 4
Standard configuration
Optional item Install Configuration
EMI Filter(9k/120k RBW) No 300Hz RBW No 10k/100kHz RBW No
Span
RBWVBW
3k10k
30k 4M10k 300k
300k 6M 60M 3G0
300k100k
(Logarithmic scale, unit in Hz)
Standard + 9k/120kHz RBW configuration
Optional item Install Configuration
EMI Filter (9k/120k RBW) Yes 300Hz RBW No 10kHz/100kHz RBW No
30k3k10k
9k 4M10k 300k
300k 600k 6M 60M 3G0 19M
120k 300k10k 100k 100k
(Logarithmic scale, unit in Hz)
Span
RBWVBW
USER’S MANUAL AE-966 / 967
02/2007 Page 101
Eng
lish
Standard + 300/9k/120kHz RBW configuration
Optional item Install Configuration
EMI Filter (9k/120k RBW) Yes 300Hz RBW Yes 10k/100kHz RBW No
30k3001k
3k 9k 4M10k 10k 300k
300k 600k 6M 60M0 19M
120k 300k10k 100k 100k
(Logarithmic scale, unit in Hz)
3G30kSpan
RBWVBW
Standard + 10k/100kHz RBW configuration
Optional item Install Configuration EMI Filter (9k/120k RBW) No 300Hz RBW No 10kHz/100kHz RBW Yes
30k3k10k
10k 4M10k 300k
300k 1M 6M 60M0 20M
100k 300k10k 100k 100k
(Logarithmic scale, unit in Hz)
3GSpan
RBWVBW
Standard + 300/10k/100kHz RBW configuration
Optional item Install Configuration EMI Filter (9k/120k RBW) No 300Hz RBW Yes 10kHz/100kHz RBW Yes
30k
30k3001k
10k 4M10k 300k
300k 1M 6M 60M0 20M
100k 300k10k 100k 100k
(Logarithmic scale, unit in Hz)
3G
3k10k
Span
RBWVBW
6.3.9.4 Set Sweep time Background Sweep time defines the display update rate. Note that the sweep time
and RBW/VBW are in trade-off. Faster sweep time updates display
more frequently but makes RBW and VBW wider, reducing the
capability to separate signals at close frequencies.
USER’S MANUAL AE-966 / 967
Page 102 02/2007
1.- Press the BW key.. BW
2.- Press F3 (Swp tm) to switch between
Auto and Manual setting.
Swp tmAuto Manu F 3
In Manual mode, the Manual Sweep Time icon appears.
Panel operation
3.- When Manual is selected, enter the sweep
time using the numerical keys.
µ
Mode Auto: Sweep time is automatically set..
Manual: Sweep time is manually set. Range 50ms ~ 12.8s, 1µs resolution.
Note When in Auto mode, optimized for fast sweep time. For narrower RBW settings, like 300 Hz and 3 KHz, this optimization will cause the phase noise slightly higher. To reduce the phase noise level, please slow down the sweep time using manual setting.
6.3.9.5 Average Waveform Background Averages the waveform for a configured number, then shows on the
display. This feature smoothes the noise level to a great extent, but slows down the display update rate.
1.- Press the BW key. BW
2.- Press F4 (AVG On) to turn On averaging. AVGOn Off
20 F 4
Panel operation (Method 1)
3.- Enter the average time using the
numerical keys
µ
1.- Press the Trace key. Trace 2.- Press F6 (More). More F 6
Panel operation (Method 2)
3.- Press F1 (AVG On) to turn On the
average mode.
AVGOn Off
20F 1
USER’S MANUAL AE-966 / 967
02/2007 Page 103
Eng
lish
4.- The average mode icon appears at the
bottom of the display.
5.- Enter the average number using the
numerical keys.
µ
Parameter 1 ~ 200: Only available when Average is On.
• Reset RBW/VBW/SweepTime to Auto
1.- Press the BW key. BW
Panel operation
2.- Press F5 (All Auto). RBW, VBW, and
Sweep time setting all changes to Auto. All Auto F 5
RBW/VBW/
Sweep
Setting
after
Autoset
All the three BW related parameters, RBW, VBW, and Sweep, will be
reset to AUTO mode when using Autoset, regardless of their previous
settings.
USER’S MANUAL AE-966 / 967
Page 104 02/2007
6.3.10 Trigger
Trigger function sets the signal conditions upon which triggers capturing waveforms, including frequency, amplitude, and delay. External signal can be used in case a special condition is required.
6.3.10.1 Free Run (Default)
In free run, captures all incoming signals (no triggering condition).
1.- Press the Trigger key. Trigger
Panel operation
2.- Press F1 (Free Run). Free Run F 1
USER’S MANUAL AE-966 / 967
02/2007 Page 105
Eng
lish
6.3.10.2 Activate video trigger
1.- Press the Trigger key. Trigger
2.- Press F2 (Trigger Condition). Select
Video.
TriggerCondition
Video Ext.F 2
3.- The video trigger icon appears at the
bottom of the display.
4.- Enter the trigger level (amplitude) using
the numerical keys. The value appears in the
command window.
µ
Video: -20dBm
5.- Press F5 (Trigger Freq) to set the
frequency at which checks the trigger
condition
Trigger Freq1.5GHz F 5
6.- Enter the trigger frequency using the
numerical keys.
µ
Panel operation
7.- To de-activate triggering, press F1 (Free
Run). Free Run F 1
Trigger level range
dBm -130 ~ +20dBm
dBmV -83.01 ~ +66.99dBmV
dBµV -23.01 ~ +126.99dBµV Trigger frequency range
0 ~ 3.0GHz
6.3.10.3 Activate external trigger
1.- Press the Trigger key. Trigger
Panel operation
2.- Press F2 (Trigger Condition). Select Ext. TriggerCondition
Video Ext.F 2
USER’S MANUAL AE-966 / 967
Page 106 02/2007
3.- The Ext. trigger icon appears at the bottom
of the display.
4.- Connect the external trigger signal to the
rear panel terminal. The positive edge
between 0V and 5V triggers.
Input level range
0 ~ 5V, positive edge trigger.
6.3.10.4 Seleccionar el modo de disparo
1.- Press the Trigger key Trigger
2.- Press F3 (Trigger Mode) repeatedly to
select the trigger modes..
Trigger ModeNorm. Sgl. Cont. F 3
Panel operation
3.- When Sgl (single) or Cont. (continuous)
is selected, you can use F6 (Run Now) to
manually start the triggering.
Run Now F 6
Modes Normal: Captures signal every time the triggering condition occurs.
Single: Captures signal when the first triggering condition occurs, then
stops capturing altogether
Continuous: captures signal when the first triggering condition occurs,
then switches to Free Run mode; continues capturing all input signals
regardless of their conditions.
USER’S MANUAL AE-966 / 967
02/2007 Page 107
Eng
lish
6.3.10.5 Set trigger delay Background Trigger delay sets the amount of time between the moment of trigger
condition and when starts capturing signal.
1.- Press the Trigger key. Trigger
2.- Press F4 (Trigger Delay). Trigger Delay1000ms F 4
Panel operation
3.- Enter the delay time using the numerical
keys.
µ
Delay range 0, 10µs ~ 100s, 1µs resolution.
6.3.11 Display
Display setting configures the LCD screen dimmer level and display layout, including display line, title, and split window. Display line provides a convenient reference line for measuring amplitude. Split window allows two simultaneous waveforms shown on the display. The VGA terminal on the rear panel outputs the LCD screen contents in 640x480 resolution.
USER’S MANUAL AE-966 / 967
Page 108 02/2007
6.3.11.1 Cambiar el Brillo de la Display
1.- Press the Display key. Display
2.- Press F1 (LCD Dimmer). LCD Dimmer F 1
Panel operation
3.- Change the brightness using the Left/Right
key or Scroll knob.
Range 0 (darkest) ~ 5 (brightest)
6.3.11.2 Activate Display Line
1.- Press the Display key. Display
2.- Press F2 (Display Line On). Display LineOn Off F 2
3.- The line appears on the display.
Display line
Panel operation
4.- The display line level appears in the
command window.
Display Line:-50dB
USER’S MANUAL AE-966 / 967
02/2007 Page 109
Eng
lish
5.- Move the line using the Arrow key or Scroll
knob.
Display line is NOT available when the display splits Note
Split window Limit Line editing
Power measurements 6.3.11.3 Enter Display Title
1.- Press the Display key. Display
2.- Press F2 (Title). Title... F 3
3.- Select the character from F2 ~ F4 and
press it.
(Capital Letter)
F 2
(Small Letter)
F 3
(Symbol) F 4
4.- Here is how to type in the capital letter “S”.
Press F2 (Capital Letter) repeatedly until the
cursor reaches S.
(Capital Letter)
F 2
Q R S T U
5.- Press the Enter key. S appears in the
command window. TL S
6.- Continue the above until all the characters
are entered.
TL SATEST
(SATEST)
7.- Press F5 (Show Title). Show Title F 5
8.- The entered title appears at the top left
corner of the display
Panel operation
9.- To erase the title, press F1 (Clear Title). Clear Title F 1
USER’S MANUAL AE-966 / 967
Page 110 02/2007
Parameter Capital letter: Upper case alphabet, A to Z.
Small letter: Lower case alphabet, a to z.
Symbol: Commonly used 14 symbols as shown below.
\ # / _ - . * : ( ) < > %
6.3.11.4 División de Display
1.- Press the Display key. Display
2.- Press F4 (Split Window). Split Window...
F 4
Panel operation
3.- The display splits into upper and lower screen. The lower display
retains the original vertical and horizontal scale. The upper display
shows full scale.
USER’S MANUAL AE-966 / 967
02/2007 Page 111
Eng
lish
4.- Select the active display (the waveform is
updated) by pressing F1 (Upper) or F2
(Lower). Pressing F3 (Alternate Sweep)
updates both displays alternately.
Upper F 1
Lower F 2
AlternateSweep
F 3
5.- To go back to the original single display,
press F4 (Full Screen). The currently active
window gets expanded.
Full Screen F 4
* Switching to Full Screen from the Alternate Sweep mode is not
recommended, since it is not predictable which display, upper or lower,
will be selected. 6.3.11.5 Use VGA Output Panel operation
Connect an external monitor to rear panel
VGA output terminal. The output is always
On.
Parameter Connector type: VGA 15pin, female.
Resolution: 640 x 480 6.3.11.6 Printout Display Image
The current waveform is printed out to an external printer.
1.- Connect the printer to front panel USB
terminal.
Panel operation
Compatibility: USB 1.1/2.0
Connector: TypeA host, female.
USER’S MANUAL AE-966 / 967
Page 112 02/2007
2.- Press the File key.. File
3.- Press F4 (Print screen). Print Screen.. F 4
4.- Press F1 (To Printer). The display is
printed out as a bitmap image. To Printer F 1
6.3.11.7 Save Display Image to USB Flash Drive
1.- Connect the printer to front panel USB
terminal.
Compatibility: USB 1.1/2.0
Connector: TypeA host, female.
2.- Press the File key.. File
3.- Press F4 (Print screen). Print Screen.. F 4
4.- Press F2 (To Ext. Memory) To Ext.Memory... F 2
5.- The USB flash drive contents appear in the window.
MyResultAMyPrintB
File Function: Print toFile
Item Name
Type: Memory External
RemarkMyPrintA
Panel operation
6.- To save the display image, press F2 (Print
Now). A new *.bmp file is created in the USB
flash drive.
Print Now F 2
USER’S MANUAL AE-966 / 967
02/2007 Page 113
Eng
lish
7.- If you want to edit the file name, press F1
(Edit File Name). Edit File Name F 1
8.- The character table appears at the bottom
of the display. Move the cursor inside the
table using the Left/Right key and Scroll knob.
Press the Enter key to confirm the character.
Char TableABCDEFGHIJKLMNOPQRSTUVWXYZabcde f
g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
9.- When completed, press F1 (Edit File
Name) again. The file name is confirmed. Edit File Name F 1
6.3.12 File/Print
File function manages file operations; copy, delete, and name change. The file format and contents include trace waveform, limit line, amplitude correction, sequence set (user defined macro), and panel setup. The file source and destination are selectable between internal and external (USB flash drive). Print function allows direct printout or saving of image via USB connector.
USER’S MANUAL AE-966 / 967
Page 114 02/2007
6.3.12.1 File Location and File Type.
Internal The internal memory. The number of file is fixed (see below).
The USB flash drive connected to the front panel terminal.
There is no practical limit on the number of files.
File location
External
The USB icon turns On when the flash drive is detected.
Compatibility: USB 1.1/2.0
Connector: TypeA host, female.
Trace Trace waveform data. File format: *.tra 13 files are available internally: Trace A/B/C (current trace), Trace 1~10 (stored trace).
Limit Limit Line data. File format: *.lmt 12 files are available internally: LimitHL (current high limit line), LimitHL1~5 (stored high limit line), LimitLL (current low limit line), LimitLL1~5 (stored low limit line).
Correction Amplitude correction data. File format: *.cor 5 files are available: Correction 1 ~ 5.
Seq. Sequence data. File format: *.seq 10 files are available: Sequence 1 ~ 10.
File Type
Setup Panel setup data. File format: *.set 10 files are available: Setup 1 ~ 10.
USER’S MANUAL AE-966 / 967
02/2007 Page 115
Eng
lish
6.3.12.2 File Copy Step
1.- When using the USB flash drive (external file) for source or destination, connect the drive to front panel terminal.
1. Connect USB flash drive (for external file)
The USB icon turns On when the flash drive is detected. 1.- Press the File key.
File
2.- Press F1 (Copy). Copy... F 1
3.- Press F1 (Source). The source file copy window appears. Source.. F 1
Source
File Function: CopyItem Name
Type: MemoryRemark
4.- Select the file type from F1 ~ F5 and press it. Then select Int (internal) or Ext (external). The display gets updated accordingly. The below example shows Trace file, internal.
TraceInt. Ext.
F 1
LimitInt. Ext.
F 2
CorrectionInt. Ext.
F 3
Seq.Int. Ext.
F 4
SetupInt. Ext.
F 5
2. Select source file
TraceCTraceB
SourceFile Function: CopyItem Name
Type: MemoryRemark
TraceA
USER’S MANUAL AE-966 / 967
Page 116 02/2007
5.- Use the Up/Down key to move the cursor to the copy source file location. (Example: TraceC selected)
TraceCTraceB
SourceFile Function: CopyItem Name
Type: MemoryRemark
TraceA
6.- Press F6 (Return). The copy source file information is retained. Return F 6
1.- Press F2 (Destination). The destination file copy window becomes active (lower half of the display). File type is automatically selected according to the previous Copy source file type selection.
Destination.. F 2
TraceCTraceB
SourceFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
TraceCTraceB
DestinationFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
Trace1Trace2Trace3
Trace1Trace2Trace3
3. Seleccionar el archivo de destino
2.- Use the Up/Down key to move the cursor to the copy destination file location. (Example: Trace1 selected)
USER’S MANUAL AE-966 / 967
02/2007 Page 117
Eng
lish
TraceCTraceB
DestinationFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
Trace1
3.- Press F6 (Return). La información del archivo de destino será guardada en la memoria.
Return F 6
4.- Copy file 1.- The copy source and destination files are highlighted (Example: source — TraceC, destination — Trace1)
TraceCTraceB
SourceFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
TraceCTraceB
DestinationFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA
Trace1Trace2Trace3
Trace1Trace2Trace3
2.- Press F4 (Copy Now). Copy Now F 4
3.- If the destination file attribute (Remark) has been empty, it changes into full.
TraceC emptyTraceB empty
DestinationFile Function: CopyItem Name
Type: Memory InternalRemark
TraceA empty
Trace1 full
USER’S MANUAL AE-966 / 967
Page 118 02/2007
1.- Move the cursor to the file using the Up/Down key.
2.- Press F3 (Edit File Name).
Edit File Name F 3
3.- The character table appears at the bottom of the display. Move the cursor inside the table using the Left/Right key and Scroll knob. Press the Enter key to confirm the character.
Char Table
ABCDEFGHIJKLMNOPQRSTUVWXYZabcde fg h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
5. Edit file name (external file, if necessary)
4.- When completed, press F3 (Edit File Name) again. The file name is confirmed. Edit File Name F 3
6.3.12.3 File Delete Step
1.- When using the USB flash drive (external file) for source or destination, connect the drive to front panel terminal.
1.- Connect USB flash drive (for external file)
The USB icon turns On when the flash drive is detected. 1.- Press the File key.
File
2.- Press F2 (Delete). Delete... F 2
3.- Press F1 (Type). The file deletion window appears. Type... F 1
2. Select source file
SourceFile Function: DeleteItem Name
Type: MemoryRemark
USER’S MANUAL AE-966 / 967
02/2007 Page 119
Eng
lish
4.- Select the file type from F1 ~ F5 and press it. Then select Int (internal) or Ext (external). The display gets updated accordingly. The below example shows Trace file, internal.
TraceInt. Ext.
F 1
LimitInt. Ext.
F 2
CorrectionInt. Ext.
F 3
Seq.Int. Ext.
F 4
SetupInt. Ext.
F 5
TraceCTraceB
SourceFile Function: DeleteItem Name
Type: Memory InternalRemark
TraceA
Trace15.- Use the Up/Down key to move the cursor to the file location. (Example: Trace1 selected)
TraceCTraceB
SourceFile Function: DeleteItem Name
Type: Memory InternalRemark
TraceA
Trace1
6.- Press F6 (Return). The file location is retained. Return F 6
1.- Press F2 (Delete Now). Delete Now F 2
3. Delete file
2.- Internal file: the file attribute (Remark) changes into Empty. In case of external file, the file itself is deleted.
TraceC fullTraceB full
SourceFile Function: DeleteItem Name
Type: Memory InternalRemark
TraceA full
Trace1 empty
USER’S MANUAL AE-966 / 967
Page 120 02/2007
6.3.12.4 File Rename Step Background File rename is allowed only for external (USB flash drive) file.
Rename operation is also available during file copy and display image save.
1.- Connect USB flash drive
When using the USB flash drive (external file) for source or destination, connect the drive to front panel terminal.
The USB icon turns On when the flash drive is detected. 1.- Press the File key.
File
2.- Press F3 (Rename). The USB flash drive contents appear on the display. Rename... F 3
3.- Move the cursor to the file using the Up/Down key.
4.- Press F3 (Edit File Name).
Edit File Name F 3
5.- The character table appears at the bottom of the display. Move the cursor inside the table using the Left/Right key and Scroll knob. Press the Enter key to confirm the character.
Char TableABCDEFGHIJKLMNOPQRSTUVWXYZabcde f
g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
2. Select file
6.- When completed, press F2 (Confirm). The file name is confirmed. Confirm F 2
USER’S MANUAL AE-966 / 967
02/2007 Page 121
Eng
lish
6.3.12.5 Printout Display Image
The current waveform is printed out to an external printer.
1.- Connect the printer to front panel USB terminal.
The USB icon turns On when the flash drive is detected
2.- Press the File key. File
3.- Press F4 (Print Screen).
Print Screen.. F 4
Panel operation
4.- Press F1 (To Printer). The display is printed out as a bitmap image. To Printer F 1
6.3.12.6 Save Display Image to USB Flash Drive
1.- Connect the printer to front panel USB terminal.
The USB icon turns On when the flash drive is detected.
2.- Press the File key. File
3.- Press F4 (Print Screen).
Print Screen.. F 4
Panel operation
4.- Press F2 (To Ext. Memory). To Ext.Memory... F 2
USER’S MANUAL AE-966 / 967
Page 122 02/2007
5.- The USB flash drive contents appear in the window.
MyResultAMyPrintB
File Function: Print toFile
Item Name
Type: Memory External
RemarkMyPrintA
6.- To save the display image, press F2 (Print Now). A new *.bmp file is created in the USB flash drive.
Print Now F 2
MyResultAMyPrintB
File Function: Print toFile
Item Name
Type: Memory External
RemarkMyPrintA
MyFigure7.- If you want to edit the file name, press F1 (Edit File Name). Edit File Name F 1
8.- The character table appears at the bottom of the display. Move the cursor inside the table using the Left/Right key and Scroll knob. Press the Enter key to confirm the character.
Char TableABCDEFGHIJKLMNOPQRSTUVWXYZabcde f
g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
9.- When completed, press F1 (Edit File Name) again. The file name is confirmed. Edit File Name F 1
USER’S MANUAL AE-966 / 967
02/2007 Page 123
Eng
lish
6.3.13 Preset Function
Pressing the Preset key brings back equipment to the below state.
Frequency Center: 1.5GHz
Start: 0Hz Stop: 3GHz Step: 1MHz
Span 3GHz Amplitude Ref.level: 0dBm
Unit: dBm Correction: OFF
Scale: 10dB/ External Gain: 0dB Input Z: 50 Ω
Autoset Amplitude Floor: Auto Span: Auto Marker Marker: OFF
Marker Table: OFF Marker Trace: Auto All Marker: OFF
Peak Search Peak Table: Off Peak Threshold: Off
Peak Sort: Freq Peak Track: Off
Trace Trace: A AVG: OFF
Mode: Clear Detection: Normal
Meas ACPR: OFF CH SPC: 0 CH BW: 600MHz OCBW %: : 0 N dB: OFF
OCBW: OFF Adj CH Offs1: 600MHz Adj CH Offs2: 1200MHz Adj CH BW1&2:600MHz N dB, Phase Jitter: OFF
Limit Line Limit A and B: OFF Pass/ Fail: Off BW RBW: Auto
Sowptime: Auto VBW: Auto Average: OFF
Trigger Trigger Delay: 50ms Trigger Mode: Normal
Trigger Freq: 1.5GHz
Display LCD Dimmer: 5 Split Window Lower: OFF
Display Line: OFF Split Window Upper: OFF
File Copy Type: Int. Trace. File rename: Ext. trace
Delete Type: Int. Trace.
System GPIB Add: 2 Aux. Sig: OFF
System Config: OFF Language: English
Option External Ref Freq: 10MHz
TG Norm Corr: OFF Demod AM: OFF
TG Output: OFF
TG Ref Value: 0dBm Demod FM: OFF
Sequence Sequence: 1 Run Mode: Single
USER’S MANUAL AE-966 / 967
Page 124 02/2007
6.3.14 System
System key configures and displays the system settings, including self-test result, date/time setting, and synchronization with other devices. The panel setting can be saved into file and recalled later, even in other equipment.
6.3.14.1 Save/Recall Panel Setting
1.- Press the System key. System
2.- Press F1 (Save/Recall Setup). Save/Recall
Setup.. F 1
3.- Press F1 or F2 repeatedly to select the setup file.
Setup1 2 3 4 5 F 1
Setup6 7 8 9 10 F 2
Panel operation
4.- Press F3 (Save Now) or F4 (Recall Now) to save or recall the panel setup file. Save Now F 3
Recall Now F 4
File contents Setup file contains the following information: - Reference amplitude level. - Amplitude unit, scale. - Start/stop frequencies. - Center and span frequencies. - VBW, RBW and sweep time. - Tracking Generator level. - Tracking Generator normalization data.
USER’S MANUAL AE-966 / 967
02/2007 Page 125
Eng
lish
• Copy/delete/rename setup file Background Setup files can be copied, deleted, or
renamed using the file utility. Press the File key to access each function.
File
Copy Press F1 (Copy). Copy... F 1
Delete Press F2 (Delete). Delete... F 2
Renombrar Press F3 (Rename). Rename... F 3
6.3.14.2 Configure Communication Interface Background Communication interface is used in the following occasions. The
interface configuration is introduced in the relevant chapter too.
PC software : USB (slave), RS-232C Remote control : USB (slave), RS-232C, GPIB (optional)
Interface type USB (slave): USB 1.1 or 2.0, TypeB mini, female connector. Used in PC software connection and remote control.
RS-232C: D-sub 9 pin, female connector. Used in PC software connection and remote control.
GPIB (optional): 24pin female connector. Used in remote control.
USB slave port configuration
No need for panel configuration: Just connect a USB cable to the rear panel. Type B mini, female, USB1.1/2.0
USER’S MANUAL AE-966 / 967
Page 126 02/2007
1.- The RS-232C configuration can be checked from the system menu. Press the System key.
System
2.- Press F3 (Serial Port). Serial Port.. F 3
3.- The RS-232C port configuration appears. Configure the PC according to this setting. Baud: 115200 Parity: Ninguno Stop: 1 Data: 8
Stop1 F 3
Baud115200 F 1
ParityNone F 2
Data8 F 4
RS-232C configuration
4.- Connect RS-232C cable to the rear panel terminal. 9 pin, female
GPIB interface is a factory installed optional item. Contact service personnel for a new installation. 1.- Press the System key..
System
2.- Press F2 (GPIB Add). GPIB Add8 F 2
3.- Select GPIB address using the Arrow key or Scroll knob. Configure the PC according to this setting.
GPIB configuration (optional)
4.- Connect GPIB cable to the rear panel terminal.
USER’S MANUAL AE-966 / 967
02/2007 Page 127
Eng
lish
1.- To check the GPIB installation status, press the System key. System
2.- Press F6 (More).
More... F 6
3.- Press F4 (System Config On). System ConfigOn Off F 4
Check GPIB installation status
4.- The system configuration window appears. When the GPIB module is installed correctly, the check box is marked.
Installed
Uninstalled
1.- To check the internal GPIB functionality result, press the System key. System
2.- Press F6 (More).
More... F 6
3.- Press F2 (Self Test). Self Test... F 2
Check GPIB self-test result
4.- The GPIB result appears at F1. If the result is Fail (underlined), contact service personnel
GPIBPass Fail F 1
GPIB constraints
Keep these rules when using GPIB interface. - Altogether less than 15 devices & 20m cable length, 2m between
each device on the bus - Unique address assigned for each device - At least 2/3 of the GPIB devices turned On - No loop or parallel structure allowed
USER’S MANUAL AE-966 / 967
Page 128 02/2007
6.3.14.3 View System Information
• View system error
View the bottom of the screen, the error message area. If there is a system error, the message appears in red color.
Center : 1.5GHz (EXT Unlock)EXTUnlock
Here is the error list.
Panel operation
EXTUnlock
RefUnlock
LO1Unlock
LO3Unlock
External reference input is not working properly Internal reference signal is not working properly. Local oscillator 1 is not working properly. Local oscillator 3 is not working properly.
• View system configuration
1.- To check system configuration, press the System key. System
2.- Press F6 (More).
More... F 6
3.- Press F4 (System Config On). System ConfigOn Off F 4
Panel operation
4.- The system configuration window appears. Four types of information are listed from the top.
- Serial number.
- Software and hardware version.
- Optional items installation.
- Reference signal selection.
USER’S MANUAL AE-966 / 967
02/2007 Page 129
Eng
lish
Serial Number
Software/ Hardware Version
Optional Item Installation Status
Reference Signal Status
5.- To close the configuration window, press F4 again (System Config Off).
System ConfigOn Off F 4
Software/hardware version
Shows versions and release date of hardware, software, and firmware. Used for service level operations.
Shows which optional item is currently installed.
: installed : uninstalled.
Optional item installation status
Sign Description
Battery pack / DC input module.
GPIB interface.
Demodulator.
Internal reference signal with middle range
stability in ±1ppm stability module.
300Hz RBW
9k/120kHz RBW included in the EMI Filter
10k/100kHz RBW Reference signal status
Checked radio button shows the reference signal used.
: enabled, : disabled.
USER’S MANUAL AE-966 / 967
Page 130 02/2007
Sign Description
Internal reference signal, standard stability.
Internal reference signal, medium stability.
Available when the ±1ppm stability module is
installed.
Internal reference signal, high stability
(reserved).
External reference signal. 6.3.14.4 Runs a series of internal tests upon power-up.
Runs a series of internal tests upon power-up. If any of the test result shows fail, contact service personnel
1.- Press the System key. System
2.- Press F6 (More). More... F 6
3.- Press F2 (Self Test). Self Test... F 2
4.- The result appears in F1 ~ F4. (The GPIB result appears only when the module is installed).
GPIBPass Fail F 1
FlashPass Fail F 2
SDRAMPass Fail F 3
RTCPass Fail F 4
Background
5.- Press F6 (Return) to go back to the previous menu. Return F 6
USER’S MANUAL AE-966 / 967
02/2007 Page 131
Eng
lish
Item GPIB: The optional GPIB interface connection. Available
only when the GPIB module is installed. Flash Internal flash memory area for storing the system
code and data. SDRAM Internal SDRAM area on which the code runs. RTC The real-time clock that controls the date and time
setting. 6.3.14.5 Set Date/Time
1.- Press the System key. System
2.- Press F6 (More). More... F 6
3.- Press F1 (System Clock). SystemClock... F 1
1. Activate clock display
4.- Press F3 (Clock On). The clock appears
on the bottom right side of the display.
ClockOn Off F 3
1.- Press F1 (Date). Date... F 1
2.- Press F1 (Year) ~ F4 (Day of Week). Enter the value using the numerical keys. Press the Enter key to confirm the value.
µ
The clock display changes accordingly.
Year F 1
Month F 2
Day F 3
Day of Week F 4
2. Set date
Year: 2000 ~ 2064
Month: 1 ~ 12 (translated to Jan ~Dec)
Day: 1 ~ 31
Day of Week: 1 ~ 7 (translated to Sun ~Sat)
USER’S MANUAL AE-966 / 967
Page 132 02/2007
1.- Press F1 (Date). Date... F 13. Set time
2.- Press F1 (Year) ~ F3 (Second). Enter the
value using the numerical keys. Press the
Enter key to confirm the value.
µ
The clock display changes accordingly.
Hour 0 ~ 23
Minute 0 ~ 59
Second 0 ~ 59
Hour F 1
Minute F 2
Second F 3
6.3.14.6 Synchronize AE-966/967 with Other Device
Using the reference frequency input/output on the rear panel, AE-966/967 can
synchronize its internal frequency with other device. AE-966/967 can become the
master (output the reference signal to other device) or the slave (input the reference
signal from other device).
6.3.14.7 AE-966/967 as a master (internal reference signal) Panel operation Connect the reference signal output terminal
on the rear panel to the other device’s
reference input.
Signal type Output level: 10MHz, 5V TTL signal (assuming the load impedance
is infinite).
Output impedance: 50 Ω
USER’S MANUAL AE-966 / 967
02/2007 Page 133
Eng
lish
1.- Press the System key. System
2.- Press F6 (More). More... F 6
3.- Press F4 (System Config On). System ConfigOn Off F 4
The system configuration window appears. The Internal Reference
Signal sign shows the status.
: enabled, : disabled.
Internal reference signal, standard stability.
Internal reference signal, median stability. Available when
the ±1ppm stability module is installed. The MED icon
appears at the bottom of the display.
Stability check
Internal reference signal, high stability (reserved). 6.3.14.8 AE-966/967 as a slave (external reference signal)
1.- Press the Option key. Option
2.- Press F4 (Ext Ref Freq) to enable
external reference signal.
Ext Ref Freq10MHz F 4
3.- Use the Arrow key to select the external
reference frequency.
4.- Connect the external reference signal to
the input terminal on the rear panel.
Panel operation
5.- The external reference signal icon
appears at the bottom of the display.
USER’S MANUAL AE-966 / 967
Page 134 02/2007
Frequency 10 types are available (units in MHz).
1.0 1.544 2.048 5.0 10.0
10.24 13.0 15.36 15.4 19.2 1.- Press the System key. System
2.- Press F6 (More). More... F 6
3.- Press F4 (System Config On). System ConfigOn Off F 4
Status check
The system configuration window appears. The External Reference
Signal sign shows the status.
: enabled, : disabled. 6.3.14.9 Service operation menu
The following functions are intended only for service personnel.
1.- Press the System key. System
2.- Press F5 (Service). Service... F 5
Optional items
maintenance
3.- In order to continue, you need to type in
the password into the command window.
PASSWORD:
1.- Press the System key. System
2.- Press F6 (More). More... F 6
RF diagnosis
3.- Press F3 (RF Diagno) to see the RF
diagnosis result. RF Diagno... F 3
USER’S MANUAL AE-966 / 967
02/2007 Page 135
Eng
lish
6.3.15 SEQUENCE (Seq)
Sequence function records and playbacks user-defined macro (measurement steps). 10 sequences are available in repeat or single running mode, each with 20 steps available for all panel operations. Delay and pause features allows observing measurement result during the sequence.
6.3.15.1 Edit Sequence
1.- Press the Sequence key.. Seq
1. Select
sequence 2.- Press F1 (sequence 1 ~ 5) or F2
(sequence 6 ~ 10) repeatedly to select the
sequence ID.
Select Seq1 2 3 4 5 F 1
Select Seq6 7 8 9 10 F 2
1.- Press F3 (Edit). Edit... F 3
2.- Press F1 (Start Edit). Start Edit F 1
2. Start editing
3.- The Start Edit sign on the middle of the
display turns green. Start Edit
USER’S MANUAL AE-966 / 967
Page 136 02/2007
20 steps are available for each sequence. Every key operation can
be recorded as a step.
Press the Enter key each time to confirm step entering. (In some
cases this is not necessary: check if the item appears in the
window).
Example: Activate system auxiliary signal.
1.- Press the System key.
2.- Press F4 (Aux Sig On).
3.- Press the Enter key.
System
Aux SigOn Off F 4
Example: Run Autoset
1.- Press the Autoset key..
2.- Press F1 (Autoset).
3.- Press the Enter key.
Autoset
Autoset F 1
2a. Add step
The result looks like this: Aux Sig OnAutoset
The delay function inserts a waiting period between steps.
1.- Press F2 (Delay ms) Delay ms100 X F 2
2b. Add delay
2.- Enter the time of delay period (100ms)
insertion using the numerical keys. For
example, pressing 5 times inserts 500ms (5 *
100ms).
Range: 1 ~ 100, 100ms resolution.
µ
2c. Pause sequence
Stops executing the sequence until the user press F1 (Continue).
Useful for observing the result of particular action (for example
ACPR measurement).
USER’S MANUAL AE-966 / 967
02/2007 Page 137
Eng
lish
1.- Press F3 (Wait to go). Wait to go F 3
2.- When the sequence is running, F1
(Continue) menu appears on the menu. Continue F 1
Inserts a whole sequence set..
1.- Press F4 (Do Seq). Do Seq... F 4
2.- Press F1 (sequence 1 ~ 5) or F2
(sequence 6 ~ 10) repeatedly to select the
inserted sequence.
Select Seq1 2 3 4 5 F 1
Select Seq6 7 8 9 10 F 2
2d. Insert another sequence
Note You cannot insert the currently edited sequence.
1.- Press F6 (More). More F 6
2.- Use the Up/Down key to move the cursor
to the insertion point.
3.- Press F1 (Insert). A new blank space will
be created. Insert F 1
Aux Sig OnAutosetDelay ms 5sNdB BW OnNdB 5
Aux Sig OnAutosetDelay ms 5s
NdB BW OnNdB 5
2e. Insert blank space
4.- Press F6 (Return) to go back to the
previous menu. Return F 6
1.- Press F6 (More). More F 6
2.- Use the Up/Down key to move the cursor
to the deletion point.
2f. Delete step
3.- Press F3 (Delete). The step will be
deleted. Delete F 3
USER’S MANUAL AE-966 / 967
Page 138 02/2007
Aux Sig OnAutosetDelay ms 5sNdB BW OnNdB 5
Aux Sig OnDelay ms 5sNdB BW OnNdB 5
4.- To undo deletion, press F5 (Undelete). Undelete F 5
5.- To go back to the previous menu, press
F6 (Return). Return F 6
1.- Press F6 (More). More F 6
2.- Press F4 (Delete All). Delete All.. F 4
3.- Press F2 (Yes) to confirm, or F1 (No) to
cancel. All steps will be deleted. No F 1
Yes F 2
Aux Sig OnAutosetDelay ms 5sNdB BW OnNdB 5
4.- To undo deletion, press F5 (Undelete). Undelete F 5
2g. Delete all steps in a sequence
5.- Press F6 (Return) to go back to the
previous menu. Return F 6
1.- Press F5 (Stop Edit). Stop Edit F 53. Stop editing
2.- The Start Edit sign on the middle of the
display turns gray. Start Edit
USER’S MANUAL AE-966 / 967
02/2007 Page 139
Eng
lish
1.- Press F6 (More). More F 6
2.- Press F2 (Save). The sequence is saved Save F 2
4. Save the edited sequence
3.- Press F6 (Return) to go back to the
previous menu. Return F 6
6.3.15.2 Delete all sequences
1.- Press the Sequence key. Seq
2.- Press F5 (Delete Seq All). DeleteSeq All... F 5
3.- Press F2 (Yes) to confirm, or F1 (No) to
cancel. All 10 sequences will be deleted No F 1
Yes F 2
4.- To go back to the previous menu, press
F6 (Return). Return F 6
Panel operation
Note: Delete Seq All cannot be recovered — the Undelete function is
not applicable. 6.3.15.3 Run Sequence
This section assumes that the sequence is already edited.
1.- Press the Sequence key. Seq
1. Select sequence
2.- Press F1 (sequence 1 ~ 5) or F2
(sequence 6 ~ 10) repeatedly to select the
sequence.
Select Seq1 2 3 4 5 F 1
Select Seq6 7 8 9 10 F 2
1.- Press F4 (Run). Run... F 4
2. Select running mode
2.- Press F1 (Run Mode) to select the
running mode, repeat (Rept) or single (Sngl).
Run ModeRept Sngl F 1
USER’S MANUAL AE-966 / 967
Page 140 02/2007
Repeat: Repeats running a sequence until F6 (Stop) is pressed.
Note: F6 (Stop)menu appears only when the sequence is
running.
Single: Runs the sequence once.
1.- Press F2 (Run Now). Run Now F 2
2.- The sequence icon appears at the bottom
of the display.
3. Run sequence
3.- To stop running, press F6 (Stop). In the
single mode, the sequence automatically
stops when all steps are completed.
Stop F 6
6.3.15.4 Save/copy/delete/rename sequence file Background Sequence files can be saved, copied,
deleted, or renamed using the file utility. Press the File key to access each function.
File
Save/Copy Press F1 (Copy). Copy... F 1
Delete Press F2 (Delete). Delete... F 2
Rename Press F3 (Rename). Rename... F 3
USER’S MANUAL AE-966 / 967
02/2007 Page 141
Eng
lish
6.3.16 TRACKING GENERATOR
The optional Tracking Generator generates a sweep signal with its sweep time and its frequency range matching the equipment system. The amplitude is maintained to a constant value over the entire frequency range, which is very useful for testing the frequency response of the Device Under Test.
6.3.16.1 Activate tracking generator.
1.- Press the Option key. Option
2.- Press F1 (TG). TG... F 1
3.- Press F1 (TG On). TGOn Off
F 1
1. Activate TG output
4.- The tracking generator output becomes
activated.
Ω
±
1.- Press F2 (TG Level). TG Level F 2
2. Set TG output level
2.- Change the TG output level using the
Arrow key and Scroll knob.
Range: 0 ~ -50dBm
USER’S MANUAL AE-966 / 967
Page 142 02/2007
6.3.16.2 Normalize tracking generator
1.- Press the Option key. Option
2.- Press F1 (TG). TG... F 1
3.- Press F5 (Ref Value). Ref Value F 5
4.- Set the reference value using the Arrow
key or Scroll knob
1. Set reference level
Normalization target level is set at Reference value, regardless of
the TG output level.
Range: - 130 ~ +20dBm
1.- Press F3 (Execute Normalization). ExecuteNormalization..
F 3
2.- Press F2 (Yes) to confirm, or F1 (No) to
cancel. Normalization runs. No F 1
Yes F 2
2. Run normalization
3.- Press F6 (Return) to go back to the
previous menu. Return F 6
1.- To enable normalization, press F4 (Norm
Corr On).
Norm CorrOn Off F 4
3. Activate normalization
2.- Normalization is activated and the TG
icon appears. 6.3.16.3 Check TG installation status
1.- Press the System key. System
1. Run normalization
2.- Press F6 (More). More... F 6
USER’S MANUAL AE-966 / 967
02/2007 Page 143
Eng
lish
3.- Press F4 (System Config On). The
configuration appears. System Config
On Off F
4.- The TG sign shows the installation status,
installed (checked) or not installed
(unchecked).
Installed
Not installed
6.3.17 DEMODULATOR (OPTIONAL)
The optional FM/AM Demodulator recovers AM or FM modulated baseband signal. The demodulated signal can be output from the rear panel mono phone jack.
6.3.17.1 Activate Demodulation
1.- Press the Option key. Option
2.- Press F2 (Demod) Demod... F 2
Panel operation
3.- Select Frequency Modulation or
Amplitude Modulation by pressing F1 (FM
On) or F2 (AM On)
FMOn Off F 1
AMOn Off F 2
USER’S MANUAL AE-966 / 967
Page 144 02/2007
6.3.17.2 Activate phone output
1.- Press F2 (Demod). Demod... F 2
2.- Press F3 (SPK On). SPKOn Off F 3
Panel operation
3.- The rear panel phone output becomes active.
3.5mm, mono (stereo plug)
Note: The FM or AM must be activated before SPK On. 6.3.17.3 Set phone output volume
1.- Press F2 (Demod). Demod... F 2
2.- Press F4 (Volume). Volume F 4
3.- The volume level appears in the command
window.
VOLUME: 30
Panel operation
4.- Change the output volume using the
Numerical keys, Arrow key, or Scroll knob.
µ
Volume level
0 ~ 63
USER’S MANUAL AE-966 / 967
02/2007 Page 145
Eng
lish
6.3.17.4 Cut off phone output noise (squelch)
1.- Press F2 (Demod). Demod... F 2
2.- Press F5 (Squelch). Squelch F 5
3.- The squelch level appears in the command
window. Output level lower than the setting is
muted.
SQUELCH
Panel operation
4.- Change the squelch level using the Numerical
keys, Arrow key, or Scroll knob.
µ
Squelch level
0 ~ 4
6.3.17.5 Check Demodulator installation status
1.- Press the System key. System
2.- Press F6 (More). More... F 6
3.- Press F4 (System Config On). The
configuration appears.
System ConfigOn Off F 4
Panel operation
4.- The Demodulator sign shows the installation
status, installed (checked) or not installed
(unchecked).
Installed
Not installed
USER’S MANUAL AE-966 / 967
Page 146 02/2007
6.3.18 EMI Filter (Optional).
The optional EMI filter is used for specific measurement situations such as EMI average detection, where higher level of sensitivity is required than the standard configuration. When this module is installed, equipment gets two additional features: Average/Quasi-peak detection mode, and 9k/120k RBW. For a new installation, contact the service center. 6.3.18.1 Select AVG/ QPeak signal detection mode
1.- Press the Trace key. Trace
2.- Press F6 (More). More F 6
3.- Press F3 (Detection). Detection.. F 3
Panel operation
4.- The signal detection mode appears. When the
EMI filter is installed, F4 (AVG) and F5 (QPeak)
becomes available.
Normal F 1
Sample F 2
Peak+ F 3
AVG F 4
QPeak F 5
Parameter AVG (average): Detects the average power level of the samples using a
low pass filter. Useful for smoothing the noise level.
QPeak (quasi-peak): Detects the quasi-peak power level of the
samples. Useful for viewing in zero span without missing signal
variations.
USER’S MANUAL AE-966 / 967
02/2007 Page 147
Eng
lish
6.3.18.2 Select 9kHz/120kHz RBW
1.- Press the BW key. BW
2.- Press F1 (RBW Manu). RBWAuto Manu F 1
Panel operation
3.- Select 9kHz/120kHz RBW using the Scroll
key. The RBW value appears in the command
window.
RBW: 9kHz Note In the automatic mode, RBW is selected according to the internal
reference setting. 6.3.18.3 Check EMI filter installation status
1.- Press the System key.. System
2.- Press F6 (More). More... F 6
3.- Press F4 (System Config On). The system
configuration window appears.
System ConfigOn Off F 4
Panel operation
4.- The 9/120k RBW sign shows the installation
status, installed (checked) or not installed
(unchecked).
Installed
Not installed
Note EMI filter (9k/120k RBW) and 10k/100k RBW are exclusive. They cannot
be installed together.
USER’S MANUAL AE-966 / 967
Page 148 02/2007
6.3.19 PC Software
It monitors the waveform and allows panel operations from the familiar PC environment, including large display and keyboard/mouse operation.
USER’S MANUAL AE-966 / 967
02/2007 Page 149
Eng
lish
6.3.19.1 Install Software • PC requirement Software OS: Windows 2000/XP Hardware USB: 1 USB host connector, 1.1 or 2.0 compatible.
6.3.19.2 Installation step 1. Activate setup software
1. Unpack the zip file.
2. Double click Setup.exe.
3. The setup screen opens. Close all other applications and click OK. If you need to quit setup, press Exit Setup.
2. Start installation
1. If you install to a specific directory, click the Change Directory button.
2. Click the icon to start installation.
USER’S MANUAL AE-966 / 967
Page 150 02/2007
3. When the successful installation message appears, click OK.
6.3.19.3 Connect Software
This section assumes the software is already installed.
• Configure interface
USB slave, or RS-232C is available.
Configure USB
No need to configure anything on GSP-830
side. Just connect the USB cable to the rear
panel. Type B mini, female connector
USER’S MANUAL AE-966 / 967
02/2007 Page 151
Eng
lish
1.- The RS-232C configuration can be checked
from the system menu. Press the System key. System
2.- Press F3 (Serial Port). Serial Port.. F 3
3.- The RS-232C port configuration appears.
Configure the PC according to this setting
Baud: 115200
Parity: None
Stop: 1
Data: 8 Stop
1 F 3
Baud115200 F 1
ParityNone F 2
Data8 F 4
Configure RS-232C
4.- Connect the RS-232C cable to the rear
panel terminal.
9 pins, female.
6.3.19.4 Invoke software PC operation 1.- Invoke the software from startup menu.
USER’S MANUAL AE-966 / 967
Page 152 02/2007
2.- The software opens.
3.- Click the setting icon. The parameter
setting window appears.
4.- Select the connection port (COM port for serial connection).
USER’S MANUAL AE-966 / 967
02/2007 Page 153
Eng
lish
Port selection: Select the port specified in the PC configuration. To check the configuration in PC, go to Control panel → System properties → Hardware tab → Device Manager
5.- Click the Setting icon again to close the
setting window.
6.- Click the Open COM Port icon. The
connection is established when the other
icons becomes active.
1.- Click the Capture icon. Make sure the
waveform shown in equipment display is
captured correctly.
Functionality check
USER’S MANUAL AE-966 / 967
Page 154 02/2007
6.3.19.5 Use Software
• Establish connection
1.- Press the setting icon and open the
parameter setting window.
2.- Select the serial port terminal.
3.- Press the COM port icon. The connection
is established when the other icons becomes
active.
Operation step
Port setting: Select the port specified in the PC configuration. To check the configuration in PC, go to Control panel → System
properties → Hardware tab → Device Manager.
• Capture waveform Operation step
1.- Click the capture icon. The current
waveform is captured and appears on the
screen.
Display
USER’S MANUAL AE-966 / 967
02/2007 Page 155
Eng
lish
• Clear waveform Operation step
1.- Click the clear trace icon. The waveform
is cleared from the screen.
Display
• Save waveform
1.- Press the setting icon. Select the file
format from *.jpg/*.bmp (screen snapshot),
*.txt (measurement data).
Operation step
2.- Press the save icon. The Windows
standard save dialogue window opens. Select
the directory and save the file.
USER’S MANUAL AE-966 / 967
Page 156 02/2007
File format The *.txt file contains the following information.
- Frequency (MHz) and Amplitude for all waveforms. - Amplitude reference level, unit, and scale. - Start, Stop, Center frequency, and frequency span. - RBW, VBW, and sweep time. - Date and time (if already configured).
• Printout screen image Operation step Click the print icon. The Windows standard
printout dialogue opens. Select the printer and printout the screen image.
Note
The screen image contrast will be reversed (background color
becomes white).
• Utilizar marcadores
1.- Click the marker icon. The marker function
window appears
Operation step
USER’S MANUAL AE-966 / 967
02/2007 Page 157
Eng
lish
2.- Select Live or Storage.
3.- Check the marker ID box. 5
markers, 0 to 4, are available
4.- Enter the frequency to each
marker.
5.- Select normal (N) or delta marker
Example:
Marker0 & Delta 1: the delta marker
shows the difference between
marker0 and marker1.
6.- The display gets updated with markers in red color and marker
values listed on the bottom.
• Exit program Operation step Click the exit icon or press Alt key + F4.
USER’S MANUAL AE-966 / 967
Page 158 02/2007
6.3.20 Remote Control
The equipment supports remote control which is partially based on IEEE 488.2 and SCPI standard. The command set covers most of the panel operations. Three interfaces are available: USB slave, RS-232, and GPIB (optional).
6.3.20.1 Configure Interface Interface type USB (slave): USB 1.1 or 2.0, TypeB mini, female connector.
RS-232C: D-sub 9 pin, female connector. GPIB (optional): 24pin female connector.
USB slave port configuration
No need for panel configuration: Just connect a USB cable to the rear panel. Type B mini, female, USB1.1/2.0
The USB icon turns On when the connection is detected.
USER’S MANUAL AE-966 / 967
02/2007 Page 159
Eng
lish
1.- The RS-232C configuration can be checked from the system menu. Press the System key.
System
2.- Press F3 (Serial Port). Serial Port.. F 3
3.- The RS-232C port configuration appears. Configure the PC according to this setting. Baud: 115200 Parity: Ninguno Stop: 1 Data: 8 Stop
1 F 3
Baud115200 F 1
ParityNone F 2
Data8 F 4
RS-232C configuration
4.- Connect the RS-232C cable to the rear panel terminal. (9 pins, female)
GPIB interface is a factory installed optional item. Contact the service center for a new installation. 1.- Press the System key.
System
2.- Press F2 (GPIB Add). GPIB Add8 F 2
3.- Select the GPIB address using the Left/Right key or Scroll knob. Configure the PC accordingly.
GPIB (optional) configuration
4.- Connect the GPIB cable to the rear panel terminal.
1.- To check the GPIB installation status, press the System key. System
2.- Press F6 (More). More... F 6
3.- Press F4 (System Config). System ConfigOn Off F 4
Check GPIB installation status
4.- The system configuration window appears. GPIB sign shows installed (checked) or not installed (unchecked)
Installed
Not installed
USER’S MANUAL AE-966 / 967
Page 160 02/2007
1.- To check the internal GPIB functionality test result, press the System key. System
2.- Press F6 (More). More... F 6
3.- Press F2 (Self Test). Self Test... F 2
Check GPIB self-test result
4.- The GPIB result appears at F1. If the result is Fail (underlined), contact the service center.
GPIBPass Fail F 1
GPIB constraints Keep these rules when using the GPIB interface.
- Altogether less than 15 devices & 20m cable length, 2m between
each device on the bus.
- Unique address assigned for each device.
- At least 2/3 of the GPIB devices turned On. - No loop or parallel structure allowed.
Functionality Check
Run this query command from the terminal. *idn? This should return the Manufacturer, Model number, Serial number, and Firmware version.
PROMAX, AE-967, P920130, V3.01
USER’S MANUAL AE-966 / 967
02/2007 Page 161
Eng
lish
7 COMMAND SYNTAX
The commands are partially compatible with IEEE488.2 (1992) and SCPI (1994) standard. Commands are NON-case sensitive. Example command meas:freq:cen _ 9 _ khz
1 2 3 4 5 1: Command Header 2: Single space 3: Parameter1 4: Single space 5: Parameter2
Command Header
Several command header elements (nodes) can be concatenated
to form a complex command.
The above example can be separated into: meas: (root node) + freq: + cen:
Parameter example
0/1 0 or 1. 1~4 Integer between 1, 2, 3, or 4. 0.01~5 Decimal number between 0.01 and 5. KHz Unit (non-case sensitive)
Message Terminator
Marks the end of a command line. Any of the following is acceptable. CR^END: Line feed code (hexadecimal 0D) with END
message CR Line feed code <dab> ^END Last data byte with END message.
Message Separator
; (semicolon) Command separator.
USER’S MANUAL AE-966 / 967
Page 162 02/2007
7.1 Comand set
- Commands are non-case sensitive
- Underline means a single space (100_mhz→100 mhz). • Frequency
Comand Description
meas:freq:cen? Returns the center frequency in kHz. Example: 1000000 khz
meas:freq:cen Sets the center frequency. Example: meas:freq:cen_100_mhz
meas:freq:st? Returns the start frequency in kHz. Example: 1000000 khz
meas:freq:st Sets the start frequency. Example: meas:freq:st_100_mhz
meas:freq:stp? Returns the stop frequency in kHz. Example: 1000000 khz
meas:freq:stp Sets the stop frequency. Example: meas:freq:stp_100_mhz
meas:freq:ss? Returns the frequency step size in kHz. Example: 1000000 khz
meas:freq:ss Sets the frequency step. Example: meas:freq:ss_100_mhz
meas:freq:cen:fw Moves the center frequency one step size forward.
meas:freq:cen:bw Moves the center frequency one step size backward.
• Span
Comand Description
meas:span? Returns the frequency span. Example: 10000 khz
meas:span Sets the frequency span. Example: meas:span:10_mhz
meas:span:full Sets the frequency span to full.
meas:span:zero Sets the frequency span to zero.
meas:span:last Recalls the last frequency span setting.
USER’S MANUAL AE-966 / 967
02/2007 Page 163
Eng
lish
• Amplitude
Comand Description
meas:refl:unit? Returns the reference level unit.
Parameter: 1 (dBm), 2 (dBmV), 3 (dBuV)
meas:refl:unit Sets the reference level unit.
Parameter: 1 (dBm), 2 (dBmV), 3 (dBuV)
Example: meas:refl:unit:_1 (dBm)
meas:refl? Returns the reference level in current unit.
Example: -30 (-30dBm cuando la unidad es dBm)
meas:refl Sets the reference level in current unit.
Example: meas:refl:_-30 (-30dBm cuando la unidad es
dBm)
meas:refl:scale? Returns the amplitude scale.
Parameter: 1(10dB/Div), 2(5dB/Div), 3(2dB/Div),
4(1dB/Div)
meas:refl:scale Sets the amplitude scale.
Parameter: 1(10dB/Div), 2(5dB/Div), 3(2dB/Div),
4(1dB/Div)
Example: meas:refl:scale_1 (10dB/Div)
meas:refl:exg? Returns the external gain/loss in dB.
Example: -6 (-6dB)
meas:refl:exg Sets the external gain/loss in dB
Example: meas:refl:exg _-6 (-6dB)
meas:refl:corr:edit Sets the amplitude correction data (frequency, amplitude).
Need to specify the table index and the number of
correction.
Example: meas:refl:corr:edit_1_CR_2,100,-40,150,-30
(table index1, 2 data, 100MHz /-40dB, 150MHz /-30dB)
meas:refl:corr:edit:del Deletes an amplitude correction point. Need to specify set
index and point index.
Example: meas:refl:corr:edit:del_5_30 (delete set 5,
point 30)
USER’S MANUAL AE-966 / 967
Page 164 02/2007
Comand Description
meas:refl:corr:edit:delall Deletes all point in an amplitude correction set. Need to
specify set index.
Example: meas:refl:corr:edit:delall_5 (delete set No.5)
meas:refl:corr:edit:quit Quits the amplitude correction mode.
meas:refl:corr:no? Returns the activated amplitude correction set.
Parameter: ninguno, 1 ~ 5 (grupo de corrección)
meas:refl:corr:on? Returns the amplitude correction set is active or inactive.
Need to specify the set index.
Parameter: on, off
Example: meas:refl:corr:on_1? (¿set No.1 is activated?)
meas:refl:corr:on Activates the amplitude correction set. Specify the set
index.
Example: meas:refl:corr:on_1 (activate set No.1)
meas:refl:corr:off Deactivates the amplitude correction set. Specify set index. Example: meas:refl:corr:off_1 (deactivate set No.1)
meas:inputz? Returns the input impedance. Parameter: 50, 75
meas:inputz Sets the input impedance. Parameter: 50, 75 Example: meas:inputz_50 (50Ω)
meas:inputz:cal? Returns the input impedance calibration value in dB.
meas:inputz:cal Sets the input impedance calibration value in dB. Example: meas:inputz:cal_5.9 (5.9dB)
• Autoset
Comand Description
meas:autoset:run Runs autoset.
meas:autoset:amp:
auto
Sets the autoset amplitude floor setting to auto mode.
meas:autoset:amp:
man
Sets the autoset amplitude floor setting to manual mode. Need to specify the amplitude in dB. Example: meas:autoset:amp:man_20 (20dB)
meas:autoset:amp:
mode?
Returns the autoset amplitude floor setting mode. Parameter: auto, manual
meas:autoset:span:
auto
Sets the autoset frequency span setting to auto mode.
USER’S MANUAL AE-966 / 967
02/2007 Page 165
Eng
lish
Comand Description
meas:autoset:span:
man
Sets the autoset frequency span setting to manual mode. Need to specify the unit. Example: meas:autoset:span:man_100_khz (100kHz)
meas:autoset:span: mode?
Returns the autoset frequency span setting mode. Parameter: auto, manual.
• Marker & Peak Search
Comand Description
meas:mark:on? Returns marker On/Off. Need to specify the marker ID. Parameter: on, off Example: meas:mark:on_1? (marker 1 On?)
meas:mark:on Turn On marker. Parameter: 1~5 (marker ID), all (all markers) Example: meas:mark:on_1 (marker 1 On)
meas:mark:off Turn Off marker. Parameter: 1 ~ 5 (marker ID), all (all markers) Example: meas:mark:off_1 (marker 1 Off)
meas:mark:norm Sets a marker to normal mode. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:norm_1 (marker 1 normal mode)
meas:mark:norm:
freq?
Returns the frequency of a normal marker. Need to specify the marker ID. Example: meas:norm:freq_1? (normal marker 1 frequency?)
meas:mark:norm:
level?
Returns the amplitude of a normal marker. Need to specify the marker ID. Example: meas:norm:level_1? (normal marker 1 amplitude?)
meas:mark:delta Sets a marker to delta mode. Also sets the relative frequency. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:delta_1 (marker 1 in delta mode) Example: meas:mark:delta_1_10_mhz (marker 1 in delta mode, relative frequency 10MHz)
meas:mark:delta:
freq?
Returns the relative frequency of a delta marker. Need to specify the marker ID. Example: meas:delta:freq_1? (frequency of delta marker 1?)
meas:mark:delta:
level?
Returns the relative amplitude of a delta marker. Need to specify the marker ID. Example: meas:delta:level_1? (amplitude of delta marker 1?)
meas:mark:tomin Moves a marker to minimum peak. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:tomin_1 (marker 1 to minimum peak)
USER’S MANUAL AE-966 / 967
Page 166 02/2007
Comand Description
meas:mark:topeak Moves a normal/delta marker to the peak. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:topeak_1 (marker 1 to peak)
meas:mark:tonp Moves a normal/delta marker to the next peak. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:tonp_1 (marker 1 to the next peak)
meas:mark:tonpr Moves a normal/delta marker to the next right peak. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:tonpr_1 (marker 1 to the next right pk)
meas:mark:tonpl Moves a normal/delta marker to the next left peak. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:tonpl_1 (marker 1 to the next left peak)
meas:mark:tocen Moves a normal/delta marker to the center frequency. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:tocen_1 (marker 1 to the center freq)
meas:mark:tost Moves a normal/delta marker to the start frequency. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:tost_1 (marker 1 to the start frequency)
meas:mark:tostp Moves a normal/delta marker to the stop frequency. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:tostp_1 (marker 1 to stop frequency)
meas:mark:toss Moves a normal/delta marker to the center frequency + step. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:toss_1 (marker 1 to center freq + step)central + paso)
meas:mark:torefl Moves a normal/delta marker to the reference level. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:torefl_1 (marker 1 to the reference level)
meas:mark:trace Moves a normal/delta marker to a trace. Parameter: 1 ~ 5 (marker ID), followed by 0 (auto), 1 (traceA), 2 (traceB), 3 (traceC) Example: meas:mark:trace_1_2 (marker 1 to traceB)
meas:mark:
marktable:on
Activates marker table.
meas:mark:
marktable:off
Deactivates marker table.
meas:mark:
peaktable:on
Activates peak table.
meas:mark:
peaktable:off
Deactivates peak table.
USER’S MANUAL AE-966 / 967
02/2007 Page 167
Eng
lish
Comand Description
meas:mark:
peaktable:sortf
Sorts peak table by frequency.
meas:mark:
peaktable:sorta
Sorts peak table by amplitude.
meas:mark:
peaktrack:on
Turns On peak track. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:peaktrack:on_1 (marker 1 tracks peak)
meas:mark:
peaktrack:off
Turns Off peak track. Parameter: 1 ~ 5 (marker ID) Example: meas:mark:peaktrack:off_1 (marker 1 no more tracks peak)
meas:mark:
peakthres:on
Turns On peak threshold and sets amplitude. Parameter: peak threshold in dB. Example: meas:mark:peakthres:on_-30 (-30dB threshold)
meas:mark:
peakthres:off
Turns Off peak threshold.
• Trazo
Comand Description
meas:tra Sets the mode for a trace. Parameter: 1 (traceA), 2 (traceB), 3 (traceC), followed by 1 (clear), 2 (peak hold), 3 (view), 4 (blank) Example: meas:tra_1_2 (traceA set to peak hold mode)
meas:tra:avg:on Turns On average mode and sets average number for a trace. Parameter: 1(traceA), 2(traceB), 3(traceC), followed by No. Example: meas:tra:avg:on_1_20 (Average trace A 20 times)
meas:tra:avg:off Turns Off the average mode. Parameter: 1 (traceA), 2 (traceB), 3 (traceC) Example: meas:tra:avg:off_1 (traceA average mode Off)
meas:tra:read? Returns trace data. Parameter:1(traceA), 2(traceB), 3(traceC), all(all three traces) Example: meas:read_1? (traceA data)
meas:tra:a <> b Swaps trace A and B.
meas:tra:a+b> a Adds trace B to A.
meas:tra:a→b> a Subtracts trace B from A.
meas:tra:const? Returns the constant value to be added or subtracted.
USER’S MANUAL AE-966 / 967
Page 168 02/2007
Comand Description
meas:tra:const Sets the constant value to be added or subtracted.
meas:tra:a+const>a Adds a constant value to traceA. meas:tra:a→const>a Subtracts a constant value from traceA.
meas:tra:det? Returns the detection mode. Parameter: 1(normal), 2(sample), 3(peak+), 4(avg), 5(qpeak)
meas:tra:det
Sets the detection mode. Parameter: 1(normal), 2(sample), 3(peak+), 4(avg), 5(qpeak) Example: meas:tra:det_4 (set the detection mode to average)
• Medidas de potencia
Comand Description
meas:ch:bw? Returns the main channel bandwidth. Example: 1000 khz
meas:ch:bw Sets the main channel bandwidth. Need to specify the unit. Example: meas:ch:bw_1_mhz (1MHz)
meas:adjc:bw? Returns the adjacent channel bandwidth in kHz. Need to specify the channel. Example: meas:adjc:bw_2? (adjacent channel2 bandwidth)
meas:adjc:bw
Sets the adjacent channel bandwidth. Need to specify the channel and unit. Example: meas:adjc:bw_2_1_mhz (adjacent channel2 bandwidth 1MHz)
meas:adjc:offs? Returns the adjacent channel offset in kHz. Specify channel. Example: meas:adjc:offs_2? (adjacent channel2 offset)
meas:adjc:offs Sets the adjacent channel offset. Specify channel and unit. Example: meas:adjc:offs_2_1_mhz (adjacent ch2 offs 1MHz)
meas:acpr? Returns ACPR measurement activation status. Parameter: on, off
meas:acpr Turns On/Off ACPR measurement. Parameter: on, off Example: meas:acpr_on (ACPR On)
meas:acpr:lower? Returns the lower ACPR result. Need to specify 1 or 2. Example: meas:acpr:lower_2? (lower ACPR 2 result?)
meas:acpr:upper? Returns the upper ACPR result. Need to specify 1 or 2. Example: meas:acpr:upper_2? (upper ACPR 2 result?)
meas:acpr:chup Moves the ACPR channel up. meas:acpr:chdown Moves the ACPR channel down.
USER’S MANUAL AE-966 / 967
02/2007 Page 169
Eng
lish
Comand Description
meas:chspc? Returns the channel space in kHz.
meas:chspc Sets the channel space. Need to specify the unit. Example: meas:chspc_10_mhz (10MHz)
meas:ocbw? Returns the OCBW activation/deactivation status. Parameter: on, off
meas:ocbw Turns On/Off OCBW. Parameter: on, off Example: meas:ocbw_on
meas:ocbw:bw? Returns the power measurement channel space in kHz. meas:ocbw:per? Returns OCBW percentage.
meas:ocbw:per Sets OCBW percentage. Example: meas:ocbw:per_90 (90%)
meas:ndb? Returns N dB activation/deactivation status. Parameter: on, off
meas:ndb Turns On/Off N dB. Parameter: on, off Example: meas:ndb_on
meas:ndb:ndb? Returns N dB.
meas:ndb:ndb Sets N dB. Example: meas:ndb:ndb_3 (3 dB)
meas:ndb:bw? Returns N dB bandwidth. Example: 1000 khz
meas:jitter? Returns Phase Jitter activation/deactivation status. Parameter: on, off
meas:jitter Turns On/Off Phase Jitter. Parameter: on, off Example: meas:jitter_on
meas:jitter:stoffs? Returns Phase Jitter start offset. Example: 0 khz
meas:jitter:stoffs Sets Phase Jitter start offset. Need to specify the unit. Example: meas:jitter:stoffs_0_khz
meas:jitter:stpoffs? Returns Phase Jitter stop offset. Example: 50 khz
meas:jitter:stpoffs Sets Phase Jitter stop offset. Need to specify the unit. Example: meas:jitter:stpoffs_50_khz
meas:jitter:phase? Returns Phase Jitter phase result in radian. Example: 1.234 rad
meas:jitter:time? Returns Phase Jitter time result in pico second. Example: 1.234 psec
USER’S MANUAL AE-966 / 967
Page 170 02/2007
• Limit Line
Comand Description
meas:lmtline:on Turns On limit line. Parameter: 0 (low limit line), 1 (high limit line) Example: meas:lmtline:on_0 (low limit line On)
meas:lmtline:off Turns Off limit line. Parameter: 0 (low limit line), 1 (high limit line) Example: meas:lmtline:off_0 (low limit line Off)
meas:lmtline:passfail Turns On/Off Pass/Fail test. Parameter: on, off Example: meas:lmtline:passfail_on (Pass/Fail test On)
meas:lmtline: passfail:criterion?
Returns Pass/Fail test criteria. Parameter: 1 (pass if all signals are in the zone), 2 (pass if the peaks are in the zone), 3 (pass if valleys are in the zone)
meas:lmtline: passfail:criterion
Sets Pass/Fail test criteria. Parameter: 1 (pass if all signals are in the zone), 2 (pass if the peaks are in the zone), 3 (pass if valleys are in the zone)Example: meas:lmtline:passfail:criterion_3
meas:lmtline:table? Returns limit line table On/Off. Parameter: on, off
meas:lmtline:table Turns On/Off limit line table. Parameter: on, off Example: meas:lmtline:table_on (limit line table On)
meas:lmtline:edit
Sets the limit line table data. Need to specify 0 (low limit line), 1(high limit line) / limit line points. Example: meas:lmtline:edit_0_CR_3,100,20,110,30,120,25 (low limit line, 3 points, 100MHz/20dB, 110MHz/30dB, 120MHz/25dB)
meas:lmtline:edit: delall
Delete all points in limit line table. Parameter: 0 (low limit line), 1(high limit line) Example: meas:lmtline:edit:delall_0 (delete low lline table)
USER’S MANUAL AE-966 / 967
02/2007 Page 171
Eng
lish
• BW
Comand Description
con:rbw:auto Sets RBW to auto. con:rbw? Returns the RBW (resolution bandwidth).
Parameter: 0 (10kHz), 1 (300Hz), 2 (3kHz), 3 (9kHz), 4 (30kHz), 5 (120kHz), 6 (300kHz), 7 (4MHz), 8 (100kHz)
con:rbw:man Selects the RBW. Parameter: 0 (200kHz), 1 (300kHz), 2 (3kHz), 3 (9kHz), 4 (30kHz), 5 (120kHz), 6 (300kHz), 7 (4MHz) Example: con:rbw:man_1 (sets RBW to 300Hz)
con:rbw:mode? Returns RBW mode. Parameter: auto, manual con:vbw:auto Sets VBW to auto.
con:vbw? Returns the VBW (video bandwidth).
Parameter: 0 (100Hz), 1 (1kHz), 2 (3kHz), 3 (10kHz), 4
(30kHz), 5 (100kHz), 6 (300kHz), 7 (4MHz)
con:vbw:man Selects the VBW.
Parameter: 0 (10Hz), 1 (1kHz), 2 (3kHz), 3 (10kHz), 4
(30kHz), 5 (100kHz), 6 (300kHz), 7 (4MHz)
Example: con:vbw:man_1 (sets VBW to 1kHz)
con:vbw:mode? Returns VBW mode.
Parameter: auto, manual
con:swt:auto Sets the sweep time to auto.
con:swt:man Sets the sweep time in msec.
Example: con:swp:man_5 (sets the sweep time to 5ms)
con:swt:mode? Returns the sweep time mode.
Parameter: auto, manual
con:allcouple Sets the RBW, VBW, and sweep time to auto. • Trigger
Comand Description
con:trig:freerun Sets the trigger to free run mode.
con:trig:video Sets the trigger to video mode. Also sets the trigger level in
current unit.
Example: con:trig:video_-20 (video mode On, -20dBm)
con:trig:single Sets the trigger condition to single.
USER’S MANUAL AE-966 / 967
Page 172 02/2007
Comand Description
con:trig:cont Sets the trigger condition to continuous.
con:trig:ext Sets the trigger to external mode.
con:trig:delay Sets the trigger delay in msec.
Example: con:trig:delay_1000 (1000ms delay)
con:trig:freq Sets the trigger frequency in MHz.
Example: con:trig:freq_1 (1MHz)
• Display
Comand Description
con:disp:dim Selects the display dimmer level.
Parameter: 0 ~ 5
Example: con:disp:dim_2 (dimmer level 2)
con:disp:dl Turns On/Off display line.
Parameter: on, off
Example: con:disp:dim_on (Activar la línea)
con:disp:dl:level Sets the display line level in current unit.
Example: con:disp:dl:level _-50 (display line at -50dBm)
con:disp:title:show Sets and shows the display title. The title is case sensitive.
Example: con:disp:title:show_SAtest (title is SAtest)
con:disp:title:clr Clears the display title.
con:disp:split:upper Turns On and sweeps upper window in split window mode.
con:disp:split:lower Turns On and sweeps lower window in split window mode.
con:disp:split:alt Sweeps the upper and lower window alternatively in split
window mode.
con:disp:split:full Goes back to full screen mode. • File
Comand Description
con:file:copy:typesel Selects the type of copied file.
Parameter: 0 (trace), 1 (limit line), 2 (correction), 3
(sequence), 4 (setup).
Example: con:file:copy:typesel_2 (copy amplitude correct
file)
USER’S MANUAL AE-966 / 967
02/2007 Page 173
Eng
lish
con:file:copy Copies file. Need to specify the source and destination file.
Parameter: ta/tb/tc (traceA/B/C), t1~10 (trace1~10), lh/ll
(high/low limit line), lh1~5 (high limit line 1~5), ll1~5 (low limit
line 1~5), c1~5 (correction set 1~5), q1~10 (sequence
1~10), file name in external USB flash drive.
Example: con:file:copy_t10_ta (copy from trace10 to
traceA)
Example: con:file:copy_ta_mytrace (copy from traceA to a
file in external USB flash named mytrace)
con:file:del:typesel Deletes the type of copied file. Parameter: 0 (trace), 1 (limit
line), 2 (correction), 3 (sequence), 4 (setup).
Example: con:file:del:typesel_2 (delete amplitude correct
file)
con:file:del Deletes file. Need to specify the source and destination file.
Parameter: ta/tb/tc (traceA/B/C), t1~10 (trace1~10), lh/ll
(high/low limit line), lh1~5 (high limit line 1~5), ll1~5 (low limit
line 1~5), c1~5 (correction set 1~5), q1~10 (sequence
1~10), file name in external USB flash drive
Example: con:file:del_t10 (delete trace10)
Example: con:file:del_myspace (delete a file names
myspace in extrenal USB flash drive)
con:file:rename Renames a file in external USB flash drive. Need to specify
the original and changed name.
Example: con:file:rename_myspace_myfile (change a file
named myspace to myfile)
con:file:prtsc:toprter Prints out the display image to connected printer.
con:file:prtsc:tofile Saves the display image to external USB flash drive. Need
to specify the file name.
Example: con:file:prtsc:tofile_myscreen (saves the
display image to a file named myscreen) • Preset
Comand Description
con:preset It re-establishes the equipment to the values defined in
factory.
USER’S MANUAL AE-966 / 967
Page 174 02/2007
• Sistema
Comand Description
con:sys:setup:save Save the current system setting to setup file.
Parameter: 1~10
Example: con:sys:setup:save_1 (save current setup to
setup1)
con:sys:setup:recall Recalls a system setting from setup file.
Parameter: 1~10.
Example: con:sys:setup:recall_1 (recall setting in setup1
file)
con:sys:gpibaddr? Returns the current GPIB address.
con:sys:gpibaddr Sets the GPIB address.
Example: con:sys:gpib:addr_2 (set GPIB address to 2)
con:sys:auxsig Turns On/Off the auxiliary signal.
Parameter: on, off
Example: con:sys:auxsig_on (Auxiliary signal On)
con:sys:clock:date? Returns the current date setting.
Parameter: year / month / day / day of week 1 (Sun) ~ 7
(Sat)
Example: 2006 6 24 7 (June 24th, Saturday, 2006)
con:sys:clock:date Sets the date.
Parameter: year / month / day / day of week 1 (Sun) ~ 7
(Sat)
Example: con:sys:clock:date_2006_6_24_7 (Jun24, Sat,
2006)
con:sys:clock:time? Returns the current time setting..
Parameter: hour / minute / second
Example: 13 30 26 (1p.m., 30 minutes, 26 second)
con:sys:clock:time Sets the time.
Parameter: hour / minute / second
Example: con:sys:clock:time_13_30_26 (1p.m., 30min,
26sec)
USER’S MANUAL AE-966 / 967
02/2007 Page 175
Eng
lish
Comand Description
con:sys:clock:show Turns On/Off clock display.
Parameter: on, off
Example: con:sys:clock:show_on (clock display On)
con:sys:selftest? Returns the self test result..
Parameter: 0 (falla), 1 (pass) in the following order:
GPIB/Flash/SDRAM/RTC.
Example: 1 1 0 1
(GPIBpass,Flashpass,SDRAMfail,RTCpass)
con:sys:lang Selects language.
Parameter: 1 (English), 2 (Simplified Chinese)
Example: con:sys:lang_2 (switch to simplified Chinese)
con:sys:ser? Returns the serial number.
Example: EE8300000
con:sys:swver? Returns the software version.
Example: 01.00 06/07/28 (version 1.00, 2006 July 28th)
con:sys:fwver? Returns the firmware version.
Example: 01.00 (Version 1.00)
con:sys:hwver? Returns hardware version in following order. RF, IF, DSP,
MB.
Example: 01.00 01.00 01.01 01.00 (RF: version 1.00, IF:
version 1.00, DSP: version 1.01, MB: version 1.00)
con:sys:optstatus? Returns optional items installation status in the following
order. 300HzRBW, EMIFilter, 10k/100kHzRBW, TG,
Demodulator, Medref (±1ppm stability)
Parameter: 0 (not installed), 1 (installed)
Example: 0 0 1 1 1 (TG, Demodulator, Medref are installed) • Option
Comand Description
con:opt:tg Turns On/Off Tracking Generator (TG).
Parameter: on, off
Example: con:opt:tg_on (TG On)
con:opt:tg:level? Returns the TG level
con:opt:tg:level Sets the TG level.
USER’S MANUAL AE-966 / 967
Page 176 02/2007
Comand Description
con:opt:tg:norm Turns On/Off TG normalization. Parameter: on, off
Example: con:opt:tg:norm_on (normalization On)
con:opt:tg:offset Sets the TG offset level.
con:opt:ge:refval? Returns the TG reference value.
con:opt:ge:refval Sets the TG reference value.
con:opt:dm:fm Turns On/Off FM in the demodulator.
Parameter: on, off
Example: con:opt:dm:fm_on (FM On)
con:opt:dm:am Turns On/Off AM in the demodulator.
Parameter: on, off
Example: con:opt:dm:am_on (AM On)
con:opt:dm:spk Turns On/Off phone output in the demodulator.
Parameter: on, off
Example: con:opt:dm:spk_on (phone output On)
con:opt:dm:vol Sets the demodulator phone output volume.
con:opt:dm:sql? Returns the demodulator squelch level.
con:opt:dm:sql Sets the demodulator squelch level.
con:opt:bat? Returns the battery level.
con:opt:extreffreq? Returns the external reference frequency.
con:opt:extreffreq Sets the external reference frequency. • Sequence
Comand Description
con:seq:runmode Selects the sequence run mode.
Parameter: 1 (repeat mode), 2 (single mode)
Example: con:seq:runmode_2 (sequence runs in sing mode)
con:seq:runseq Runs the sequence. Parameter: sequence index, 1 ~ 10
Example: con:seq:runseq_2 (run sequence 2)
con:seq:stopseq Stops the running sequence.
con:seq:delallseq Deletes all programmed sequence.
con:seq:delseq Deletes a sequence.
Parameter: sequence index, 1 ~ 10
Example: con:seq:delseq_2 (delete sequence 2)
USER’S MANUAL AE-966 / 967
02/2007 Page 177
Eng
lish
8 MAINTENANCE
8.1 Battery / DC Operation
Battery/DC operation kit is an optional item for using AE-966/967 in outdoor environment, such as field operation using battery and automobile using DC outlet.
8.1.1 Battery Operation
Turn Off the main power switch before inserting
or removing the battery pack.
Package removal / insertion
Take out the battery when not in use for a long time. Turn the knob to open the battery compartment.
USER’S MANUAL AE-966 / 967
Page 178 02/2007
1.- Press the Option key. Option
2.- Press F3 (Battery). The level icon appears
at display bottom. Battery F 3
Check Battery level
Fully charged
75 % ~ 50 %
50 % ~ 25 %
Menos del 25 %
Note: Regardless of this operation, equipment shows the icon for 5
seconds every 30 minutes. Parameters Usage time: 3 hours (typical).
Charge time: 3 hours (typical).
8.1.2 DC Operation Panel operation
Connect the DC power cable to the rear panel
input connector. Parameter 12V, 40W max.
Note: DC’s power connector (with a light plug for the use of car) is available
as another optional article, AA-12.
USER’S MANUAL AE-966 / 967
02/2007 Page 179
Eng
lish
• Check Battery/DC module installation status
1.- Press the System key. System
2.- Press F6 (More). More... F 6
3.- Press F4 (System Config On). The
configuration appears.
System ConfigOn Off F 4
Panel operation
4.- The Battery sign shows the installation
status, installed (checked) or not installed
(unchecked)..
Installed
Not installed
8.2 Replacing the mains fuse
The fuseholder lid is placed in the mains base:
1) Disconnect the power cord.
2) With an appropriate screw driver remove the fuseholder lid.
3) Substitute the melt fuse for another of identical characteristics.
FUSE TYPE SHOULD BE 5 x 20mm, 250 V SLOW T and of 1.6 A. AVOIDING THESE DIRECTIONS COULD DAMAGE THE EQUIPMENT.
4) Insert the fuseholder lid.
USER’S MANUAL AE-966 / 967
Page 180 02/2007
8.3 Cleaning recommendations
CAUTION To clean the cover, take care the instrument is disconnected.
CAUTION
Do not use scented hydrocarbons or chlorized solvents. Such products may attack the plastics used in the construction of the cover.
The cover should be cleaned by means of a light solution of detergent and
water applied with a soft cloth. Dry thoroughly before using the system again.