----------------------------CONFIGURACION MA5616 - FTTC----------------------------
---------------USUARIO Y CONTRASEA DEL MA5616------------------usuario:rootpassword: mduadmin
==============================Cambio a protocolo SIP===================================enableconfig
protocol support sip y
save
reboot system
=============================Configuracion Autosave ===========================================
enableconfig
autosave interval on
==========================Confirmacion de tarjetas de servicio=========================
board confirm 0
==================Cuando sube el equipo por GPON=======================================
port mode 0/0 gpony
port mode 0/1 gpony
==========================Asignacion de Nemonico=======================================
* El nombre del equipo varia segun dataplan
sysname MN_ATLHIGZERS_O_16T_Bquilla_AlamedaTowers
==========================Configuracion Zona Horaria=======================================
timezone GMT- 5:00
======================Asignacion descripcion del puerto================================
* Se le debe poner descripcion al puerto de uplink del equipo , la descripcion es el nombre de la OLT y el puerto al que se conecta.
port desc 0/0/0 description BAQ_CARIBE_OLT_SLOT5_PTO_2
==========================Comisionamiento Gestion======================================
**** Las vlans, Direcciones Ips y Gateways varian segun dataplan. En el siguiente caso IP: 10.33.23.3 , GATEWAY: 10.33.23.1 , MASCARA: 29
enable
config
Vlan 3 Standar
Interface vlanif 3
ip address 10.34.5.155 27
quit
port vlan 3 0/0 0
port vlan 3 0/0 1
ip route-static 0.0.0.0 0.0.0.0 10.34.5.129
=============================Configuracion vlan de servicio============================
* La vlan de servicio varia segun dataplan. En el siguiente ejemplo la VLAN de servicio es 3012.
vlan 3890 smart
vlan attrib 3890 stacking
port vlan 3890 0/0 0
port vlan 3890 0/0 1
============================Configuracion multi-service-port==========================
* La vlan de servicio varia segun dataplan. En el siguiente ejemplo la VLAN de servicio es 3012.
multi-service-port vlan 3890 board 1 vpi 8 vci 35 rx-cttr 6 tx-cttr 6y
multi-service-port vlan 3890 board 2 vpi 8 vci 35 rx-cttr 6 tx-cttr 6y
multi-service-port vlan 3890 board 3 vpi 8 vci 35 rx-cttr 6 tx-cttr 6y
multi-service-port vlan 3890 board 4 vpi 8 vci 35 rx-cttr 6 tx-cttr 6y
stacking label vlan 3890 baselabel 100y
============================Configuracion VLAN 3400 para servicio VOIP==========================
*La siguiente configuracion siempre debe hacerse, la VLAN nunca cambia.
vlan 3400 smart
port vlan 3400 0/0 0
port vlan 3400 0/0 1
multi-service-port vlan 3400 board 1 vpi 0 vci 33 rx-cttr 6 tx-cttr 6y
multi-service-port vlan 3400 board 2 vpi 0 vci 33 rx-cttr 6 tx-cttr 6y
multi-service-port vlan 3400 board 3 vpi 0 vci 33 rx-cttr 6 tx-cttr 6y
multi-service-port vlan 3400 board 4 vpi 0 vci 33 rx-cttr 6 tx-cttr 6y
traffic table ip cir 256 priority 6 priority-policy tag-In-Package
=================================Usuarios de Gestion===================================
terminal user name
Sigrest3l3c0n1c4#t3l3c0n1c4#root34SIGRES
terminal user namegestiongestion1234gestion1234root24gestion
terminal user namemanttoT3l3c0m.T3l3c0m.root13mantto
terminal user passwordrootmduadmindsl4m0v1st4rdsl4m0v1st4rn
================================Perfiles de Navegacion=================================
adsl line-profile add 199yspeed_128K 1y01110y
10101y60316031y321603264
y
adsl line-profile add 2ySpeedy1y011112y8031803129212ny224125032896
y
adsl line-profile add 6ySpeedy_20481y0111
12y8031803129212ny2242500321300
y
adsl line-profile add3ySpeedy_4M1y011112y6031603139012y606000y2245000321300
yadsl line-profile add 989ySpeedy_6M1y011112y6031603139012ny22478001281300
y
adsl line-profile add4ySpeedy_8M1y011112y6031603139012y6060
00y22410000321500
y
adsl line-profile add 988ySpeedy_10M1y011112y6031603139012ny224130001281300
y
adsl line-profile add 987ySpeedy_11M1y011112y60
31603139012ny224143001281300
y
adsl line-profile add 986ySpeedy_13M1y011112y6031603139012ny224169001281300
adsl line-profile add8ySpeedy_14M1y01
1112y6031603139012y606000y22414000321300
y
adsl line-profile add9ySpeedy_18M1y011112y6031603139012y606000y224
18000321300
y
adsl line-profile add 20ySpeedy_20M1y01111y10101y60316031y3226000321800
adsl line-profile add 998ySpeedy_1MU1y011112y6031603139012ny
22413001281300
y
adsl line-profile add 997ySpeedy_3M1y011112y6031603139012ny22439001281300
y
adsl line-profile add 996ySpeedy_5M1y011112y603160313
9012ny22465001281300
y
adsl line-profile add 995ySpeedy_7M1y011112y6031603139012ny22491001281300
y
adsl line-profile add 994ySpeedy_9M1y011112y6
031603139012ny224117001281300
y
adsl line-profile add 993ySpeedy_12M1y011112y6031603139012ny224156001281300
y
adsl line-profile add 992ySpeedy_15M1y01
1112y6031603139012ny224195001281300
y
====================Comisionamiento Anexo M Prueba 20 M================================
adsl extline-profile add 4yAnnexM_pruebannnnny44y9nnnnnnnnnnn
==============================Comunidades SNMP========================================
snmp-agent community read public
snmp-agent community write private
snmp-agent community read totem_ro
snmp-agent sys-info version v1 v2c
snmp-agent target-host trap-hostname Netcool address 10.30.4.132 trap-paramsname Netcool
snmp-agent target-host trap-hostname SAS address 10.30.4.155 trap-paramsname SAS
snmp-agent target-host trap-hostname SIGRES1 address 192.168.254.143 trap-paramsname SIGRES1
snmp-agent target-host trap-hostname SIGRES2 address 192.168.254.144 trap-paramsname SIGRES2
snmp-agent target-host trap-hostname SIGRES3 address 192.168.254.145 trap-paramsname SIGRES3
snmp-agent target-host trap-hostname SIGRES4 address 192.168.254.146 trap-paramsname SIGRES4
snmp-agent target-host trap-hostname Primaster address 10.30.7.10 udp-port 162 trap-paramsname Primaster
snmp-agent target-host trap-hostname Secmaster address 10.30.7.11 udp-port 162 trap-paramsname Secmaster
snmp-agent target-host trap-paramsname Primaster v1 securityname aaa
snmp-agent target-host trap-paramsname Secmaster v1 securityname aaa
snmp-agent trap enable standard
=============================Servidor radius==========================================
radius-server template radius2radius-server shared-key t3l3c0mradius-server authentication 10.30.4.253 1812 undo radius-server user-name domain-includedradius-server traffic-unit mbyte
quit
radius-server template radius1radius-server shared-key t3l3c0mradius-server authentication 10.30.4.115 1645
undo radius-server user-name domain-includedradius-server traffic-unit mbyte
quitaaa authentication-scheme huawei authentication-mode radius
quitdomain telecom authentication-scheme huawei radius-server radius2 quit
======================Cambio de perfil de puertos 1M===================================
* Se debe probar la navegacion de 1 M en todos los puertos anteriormente enviados
interface adsl 0/1
deactivate all
activate all profile-index 2
quit
interface adsl 0/2
deactivate all
activate all profile-index 2
quit
--------------------------------------------------------------------no aplica para las tarjetas ASPB(SLOT 3) Y VCMM (SLOT 4)----------------------------------------------------------------
interface adsl 0/3
deactivate all
activate all profile-index 2
quit
interface adsl 0/4
deactivate all
activate all profile-index 2
quit
======================Ejemplo Configuracion de 1 Puerto a 20M===================================
*A continuacion un ejemplo de configuracion de un puerto a 20 M, para estas pruebas se deberan configurar los puertos anteriormente enviados. Para el siguienteejemplo se configurar el puerto 2 de la tarjeta 1
interface adsl 0/1 deactivate 24activate 24 profile-index 20extline-config 24 profile-index 4quit
interface adsl 0/2 deactivate 31activate 31 profile-index 20extline-config 31 profile-index 4quit
================SI EL EQUIPO TIENE TARJETAS DE VOZ CONFIGURAR LO SIGUIENTE==========================
=============================Configuracion vlan de Voz===============================
* Las direcciones IPs y Gateway varian segun dataplan. En la siguiente configuracion IP : 10.220.15.137 Gateway : 10.220.15.129 Mascara: 27
vlan 70 smart
interface vlanif 70
ip address 10.220.15.137 27
quit
port vlan 70 0/0 0
port vlan 70 0/0 1
ip route-static 10.220.0.0 255.255.255.0 10.220.15.129
===========================Configuracion voip=========================================
* Las direcciones IPs y Gateway varian segun dataplan. En la siguiente configuracion IP : 10.220.15.137 Gateway : 10.220.15.129
voip
ip address media 10.220.15.137 10.220.15.129 ip address signaling 10.220.15.137 qos ip media 10.220.15.137 dscp 46 qos ip signaling 10.220.15.137 dscp 26
quit
==========================Configuracion interface SIP=================================
* Las direcciones IPs y Gateway varian segun dataplan. En la siguiente configuracion IP : 10.220.15.137
interface sip 0y
if-sip attribute basic media-ip 10.220.15.137 signal-ip 10.220.15.137 signal-port 5060 home-domain ims.movistar.co
if-sip attribute basic primary-proxy-ip1 10.220.0.12 primary-proxy-port 5060
if-sip attribute basic sipprofile-index 0
if-sip attribute optional sub-ua-profile disable sdp-negomode local
if-sip attribute optional proxy-check-mode option
if-sip attribute optional proxy-dual-home no proxy-refresh-mode no-switch
fax-modem parameters vbd-codec G.711U
rfc2833 set rfc2833-negomode negostart mg-software parameter 2 1
mg-software parameter 13 1
mg-software parameter 23 1800
sipprofile delete codec-pri all
sipprofile add codec-pri 0 18 20
sipprofile add codec-pri 1 4 30
sipprofile add codec-pri 2 0 20
sipprofile add codec-pri 3 8 20
sipprofile modify syspara 63 30
sipprofile modify syspara 130 1
sipprofile modify syspara 134 1
sipprofile modify syspara 135 1
sipprofile modify syspara 139 1
sipprofile modify syspara 140 1
sipprofile modify syspara 152 1
sipprofile modify syspara 157 0
sipprofile modify syspara 186 3
sipprofile modify syspara 188 0
sipprofile modify syspara 193 60
sipprofile modify syspara 208 600
sipprofile modify syspara 210 1
sipprofile modify syspara 290 1
digitmap-timer short 5
mg-software strpara 5 57
mg-software strpara 6 1
fax-modem parameters negomode self-switch rtp-interval 3
fax-modem parameters rtp-interval 3
resety
quit
oversea parameters 0 670
============================Reinicio de tarjetas=======================================
board reset 0/1yboard reset 0/2yboard reset 0/3yboard reset 0/4y
================================Pruebas internas=======================================
*Para el siguiente caso las pruebas internas se configuran para la tarjeta 3
undo port vlan 70 0/0 0
undo port vlan 70 0/0 1
esl user
sippstnuser batdel 0/3/0 0/3/63 y
sippstnuser batadd 0/3/0 0/3/63 0 telno 100
quit
UNA VEZ FINALIZADAS LAS PRUEBAS SE DEBE REALIZAR LA SIGUIENTE CONFIGURACION PARA PODER REALIZAR PRUEBAS CON NUMEROS REALES
port vlan 70 0/0 0
port vlan 70 0/0 1
esl user
sippstnuser batdel 0/3/0 0/3/63 y
======================Configuracion numeros de prueba==================================
**** Despues de configurado alguno de los numeros con los comandos mas abajo listados, con el siguiente comando se puede verificar si el numero registra para poder hacer las pruebas
MA5600T(config)#display sippstnuser reg-state 0/15 -------------------------------------------------------- F /S /P MGID RegisterState TelNo -------------------------------------------------------- 0 /3/0 0 Active 5724064998 --------------------------------------------------------
esl user
sippstnuser add 0/3/0 0 telno 5724064998
sippstnuser auth set 0/3/0 telno 5724064998 password-mode [email protected]
T3l3f0n1c4C98
sippstnuser rightflag set 0/3/0 telno 5724064998 ct disable dc disable conf disable cw enable
sippstnuser add 0/15/1 0 telno 5747813601
sippstnuser auth set 0/15/1 telno 5747813601 password-mode [email protected]
sippstnuser rightflag set 0/15/1 telno 5747813601 ct disable dc disable conf disable cw enable
sippstnuser add 0/2/0 0 telno 5747813602
sippstnuser auth set 0/2/0 telno 5747813602 password-mode [email protected]
sippstnuser rightflag set 0/2/0 telno 5747813602 ct disable dc disable conf disable cw enable
sippstnuser add 0/3/0 0 telno 5747813603
sippstnuser auth set 0/3/0 telno 5747813603 password-mode [email protected]
sippstnuser rightflag set 0/3/0 telno 5747813603 ct disable dc disable conf disable cw enable
sippstnuser add 0/4/0 0 telno 5747813604
sippstnuser auth set 0/4/0 telno 5747813604 password-mode [email protected]
sippstnuser rightflag set 0/4/0 telno 5747813604 ct disable dc disable conf disable cw enable
sippstnuser add 0/5/0 0 telno 5747813605
sippstnuser auth set 0/5/0 telno 5747813605 password-mode [email protected]
sippstnuser rightflag set 0/5/0 telno 5747813605 ct disable dc disable conf disable cw enable
sippstnuser add 0/6/0 0 telno 5747813606
sippstnuser auth set 0/6/0 telno 5747813606 password-mode [email protected]
sippstnuser rightflag set 0/6/0 telno 5747813606 ct disable dc disable conf disable cw enable
sippstnuser add 0/7/0 0 telno 5747813607
sippstnuser auth set 0/7/0 telno 5747813607 password-mode [email protected]
sippstnuser rightflag set 0/7/0 telno 5747813607 ct disable dc disable conf disable cw enable
sippstnuser add 0/8/0 0 telno 5747813608
sippstnuser auth set 0/8/0 telno 5747813608 password-mode [email protected]
sippstnuser rightflag set 0/8/0 telno 5747813608 ct disable dc disable conf disable cw enable
sippstnuser add 0/12/0 0 telno 5747813609
sippstnuser auth set 0/12/0 telno 5747813609 password-mode [email protected]
sippstnuser rightflag set 0/12/0 telno 5747813609 ct disable dc disable conf disable cw enable
sippstnuser add 0/13/0 0 telno 5747813610
sippstnuser auth set 0/13/0 telno 5747813610 password-mode [email protected]
sippstnuser rightflag set 0/13/0 telno 5747813610 ct disable dc disable conf disable cw enable
sippstnuser add 0/14/0 0 telno 5747813611
sippstnuser auth set 0/14/0 telno 5747813611 password-mode [email protected]
sippstnuser rightflag set 0/14/0 telno 5747813611 ct disable dc disable conf disable cw enable
sippstnuser add 0/15/0 0 telno 5747813612
sippstnuser auth set 0/15/0 telno 5747813612 password-mode [email protected]
sippstnuser rightflag set 0/15/0 telno 5747813612 ct disable dc disable conf disable cw enable
sippstnuser add 0/16/0 0 telno 5747813613
sippstnuser auth set 0/16/0 telno 5747813613 password-mode [email protected]
sippstnuser rightflag set 0/16/0 telno 5747813613 ct disable dc disable conf disable cw enable
sippstnuser add 0/17/0 0 telno 5747813614
sippstnuser auth set 0/17/0 telno 5747813614 password-mode [email protected]
T3l3f0n1c4C14
sippstnuser rightflag set 0/17/0 telno 5747813614 ct disable dc disable conf disable cw enable
sippstnuser add 0/18/0 0 telno 5747813615
sippstnuser auth set 0/18/0 telno 5747813615 password-mode [email protected]
sippstnuser rightflag set 0/18/0 telno 5747813615 ct disable dc disable conf disable cw enable
sippstnuser add 0/11/0 0 telno 5747813600
sippstnuser auth set 0/11/0 telno 5747813600 password-mode [email protected]
sippstnuser rightflag set 0/11/0 telno 5747813600 ct disable dc disable conf disable cw enable
======================Configuracion Alarmas Externas==================================
* Antes de configurar las alarmas externas se debe verificar que la emu 1 sea la ESC, se puede verificar con el comando MA5616(config)#display emu , de lo contrariose debe cambiar el id para entrar a configurar la EMU, es decir, si esta configurada con el ID 0 , el primer comando debe ser interface emu 0
interface emu 1
esc digital 0 name Temperature available-level low-level
esc digital 1 available-level low-level
esc digital 2 name SPD available-level low-level
esc digital 3 name Wiring available-level low-level
Top Related