Máquina Perforadora-Rotativa Universal Rotary Drilling Rig · prakla.de Prakla Bohrtechnik...
Transcript of Máquina Perforadora-Rotativa Universal Rotary Drilling Rig · prakla.de Prakla Bohrtechnik...
Prak
la B
ohrte
chni
kRB 50
Máquina Perforadora-Rotativa UniversalRotary Drilling Rig
905-645-5_11-2014_RB50.indd 1905-645-5_11-2014_RB50.indd 1 28.01.2015 10:10:0928.01.2015 10:10:09
RB 50 © PRAKLA Bohrtechnik GmbH 11/2014
RB 50
9050
4000
11850
4000
9623
1630
500
7200
1970
13350
La Maquina de perforación móvil con una carga de gancho de 500 kNLa RB 50 con una capacidad de tiro
de 500 kN ha sido completamente
modernizada, potenciada y diferenciada
de su modelo anterior.
El taladro multipropósito RB 50 permite
perforar diferentes diámetros hasta 47"
(1,200 mm) mediante los siguientes
métodos:
Perforación de circulación directa l
Perforación de circulación inversa l
Perforación giratoria en seco con l
barrena (perforación helicoidal)
Perforación con tubo testigo (saca l
núcleos)
Perforación de testigo mediante cable l
“Wire Line”
Perforación con martillo en fondo l
Perforación de percusión con cable l
Perforación inclinada l
The mobile rotary drilling rig with 500 kN hook load capacityThe universal rotary drilling rig RB 50 has
been completely reworked and upgraded,
technically as well as power-wise.
The RB 50 universal drilling rig enables
each user to drill with the following
methods, with borehole diameters up to
47" (1.200 mm):
Rotary-drilling with direct circulation l
Rotary-drilling with reverse circulation l
Auger drilling l
Percussion core drilling (ram coring) l
Wire-line core drilling l
Down-The-Hole hammer drilling l
Free-fall drilling l
Direction deviation drilling l
905-645-5_11-2014_RB50.indd 2905-645-5_11-2014_RB50.indd 2 28.01.2015 10:10:1328.01.2015 10:10:13
© PRAKLA Bohrtechnik GmbH 11/2014 RB 50
Especificaciones técnicas
Chassis Chassis
Camión 3 Ejes 3-axle-truck 6 x 6 6 x 6
MAN TGA 33.440 e.g. MAN TGA 33.440 323 kW 434 HP
Torre de Perf. Mast
Altura torre s.n.suelo Mast height aGL 13,5 m 44.3 ft
Altura instalación de Casing Casing installation height 8,0 m 26.2 ft
Carrera del Cabezal de Perf. Free working height power swivel 7,2 m 23.6 ft
Carga de Gancho operación regular Regular operational hook load 400 kN 89,924 lbf
Carga de Gancho max. permitida Max. permissible hook load 500 kN 112,400 lbf
Avance (Cilindros hydr.) Feed device (hydr. cylinder)
Pull down / Pull-back Pull down / Pull-back force 80 / 190 kN 17,984 / 42,713 lbf
Velocidad de avance Feed speed 0 – 0,8 m/s 0 – 2.6 ft/sec.
Cabezal de perforación (rot.) Power swivel
Caja de 3 Velocidades Gear select, 3 speeds
Torque a: 0 – 43 rpm Torque at 0 – 43 rpm 31.580 Nm 23,290 lbf-ft
Torque a: 0 – 82 rpm Torque at 0 – 82 rpm 16.600 Nm 12,244 lbf-ft
Torque a: 0 – 330 rpm Torque at 0 – 330 rpm 4.150 Nm 3,060 lbf-ft
Diametro Interior del Cabezal (paso) I.D. hollow shaft 150 mm 5 7/8"
Grua principal Main winch
Linea de tiro 1era vuelta Line pull 1st layer 95 kN 21,357 lbf
Linea de tiro (6-vuelta crane block) Line pull (6-fold crane block) 500 kN 112,404 lbf
Winche de Corazonamiento Coring winch / sand winch
Linea de tiro 1era vuelta Line pull 1st layer 20 kN 4,500 lbf
Diametro del cable/ largo cable Wire rope diameter / Rope length 8 mm / 1.600 m 5/16" / 5,249 ft
Bomba Centrifuga Centrifugal pump
Capacidad descarga Discharge capacity 3.200 l/min. 845 gal/min
Presión oper. Operating pressure 7 bar 101 psi
Compresor Compressor
Capacidad descarga Discharge capacity 13,2 m³/min 466 cfm
Presión oper. Operating pressure 14 bar 203 psi
Accesorios especiales Special equipment
Torre extensible Mast extension
Altura torre s.n.suelo Mast height aGL 17,9 m 59 ft
Altura instalación de Casing Casing installation length 14,6 m (Casing R III) 48 ft (Casing R III)
Torre version R2 Mast version R2
Altura torre s.n.suelo Mast height aGL 16,4 m 54 ft
Altura instalación de Casing Casing installaton height 11,5 m (Casing R II) 38 ft (Casing R II)
Carrera del Cabezal de Perf. Free working height power swivel 10,9 m (Drill pipe R II) 36 ft (Drill pipe R II)
Oiler Oiler
Bomba de Espuma Foam mud pump
Bomba de Pistón Piston mud pump
Guia de Cable Corazonamiento Cable spooling device
Motor a Bordo Deck engine
Otras alternativas y accesorios de
acuerdo a especifi caciones del Cliente
tras revisión técnica.
Further alternatives acc. to customer
specifi cation after technical clarifi cation
Technical specifications
905-645-5_11-2014_RB50.indd 3905-645-5_11-2014_RB50.indd 3 28.01.2015 10:10:1328.01.2015 10:10:13
prakla.de
Prak
la B
ohrte
chni
k
905.645.5 11/2014
Los desarrollos de diseño y las mejoras de procesos podrían requerir
la actualización o modifi cación de especifi caciones y materiales
sin previo aviso y sin que la empresa asuma responsabilidad
alguna al respecto. Es posible que en las ilustraciones se incluya
equipamiento opcional y no se muestren todas las confi guraciones
posibles. Tanto las ilustraciones como los datos técnicos se ofrecen
a título meramente indicativo. La empresa no se hace responsable
de posibles informaciones erróneas o erratas de imprenta.
PRAKLA Bohrtechnik GmbH
Moorbeerenweg 3
31228 Peine
Alemania
Tel: +49 51 71 90 55-0
Fax: +49 51 71 90 55-100
www.prakla.de
Design developments and process improvements may require the
specifi cation and materials to be updated and changed without
prior notice or liability. Illustrations may include optional equipment
and not show all possible confi gurations.
These and the technical data are provided as indicative information
only, with any errors and misprints reserved.
905-645-5_11-2014_RB50.indd 4905-645-5_11-2014_RB50.indd 4 28.01.2015 10:10:1328.01.2015 10:10:13