CE 586 PRECIPITACIÓN Y FLOCULACIÓN - gunt.de · papel en un archivador, y también como archivo...
Transcript of CE 586 PRECIPITACIÓN Y FLOCULACIÓN - gunt.de · papel en un archivador, y también como archivo...
63
LA DOCUMENTATION DIDACTIQUE
TÉCNICA DE MEDICIÓN Y REGULACIÓN ARMARIO DE DISTRIBUCIÓN
PROCESO CONTINUO Y PRÁCTICO
El material didáctico, bien estructurado, representa los fundamentos y guía paso a paso por los distintos ensayos. El material didáctico se suministra impreso en papel en un archivador, y también como archivo PDF en un CD.
Actualizaciones Si surgen novedades o complementos para el sistema CE 586, especialmente en lo que concierne al material didáctico, usted será informado como cliente de GUNT.
Utilización de la técnica de medición y regulación moderna
Caudalímetro
Sensor de conductividad
Sensor de temperatura
Regulación del pH en el depósito de precipitación
Elementos de manejo de todos los componentes principales
Disposición clara de los elemen- tos de manejo
Indicación digital de los valores medidos
Regulador digital del pH
Un esquema de proceso, claro y de gran tamaño, en el armario de distribución, permite una identifica-ción sencilla de todos los compo-nentes.
CE 586 PRECIPITACIÓN Y FLOCULACIÓN
Depósito de precipitación Depósito de floculación Decantador lamelar
Bombas dosificadoras
Adición precisa de sustan-cias químicas mediante el uso de bombas dosificado-ras industriales
Material didáctico de CE 586
1 2 3E N E R G Y & E N V I R O N M E N T
CE 586 PRECIPITATION AND FLOCCULATION
3 Unit description
33
All
right
s re
serv
ed, G
.U.N
.T. G
erät
ebau
, Bar
sbüt
tel,
Ger
man
y 03
/201
0
– Plug the supply unit connector into the con-
necting socket on the switch cabinet (item
56 in Fig. 3.11, Page 23).
• Connect the unit to the mains electricity supply.
• Make sure that the valves on the unit are
closed, except for valves V3 and V9.
Valve V3 is shown in Fig. 3.24. Valves V3 and
V4 are closed by turning the hand wheel clock-
wise. They are opened by turning the hand
wheel anticlockwise.
• Fill the raw water tank (B1) with water.
• Fill tanks B6, B7 and B8 with water.
• Set the main switch (item 57 in Fig. 3.11,
Page 23) to "1".
• Start the raw water pump (P1). If necessary,
add more water to the raw water tank (B1).
• Start pumps P2 to P4. If necessary, add more
water to tanks B6 to B8.
• Fill the trainer until treated water flows into the
treated water tank (B4).
• Start the sludge pump (P5).
• Continue operating the unit until the treated
water tank (B4) is full.
• Repair any leaks that occur.
• Stop pumps P1 to P5.
• Drain the entire unit.
• Remove the pH value sensors, observing the
instructions in Chapter 3.4.3, Page 28ff.
• Remove the conductivity sensors, observing
the instructions in Chapter 3.4.4, Page 31.
Fig. 3.22 Hose line for raw water, on
supply unit
Fig. 3.23 Hose line for raw water, on
trainer
Fig. 3.24 Valves V3 and V4V3
V4
áctico de CE 586
33
,
y,
ore
the
eated
ving the
ff.
observing
ge 31.
E N E R G Y & E N V I R O N M E N T
CE 586 PRECIPITATION AND FLOCCULATION
3 Unit description
21
All
right
s re
serv
ed, G
.U.N
.T. G
erät
ebau
, Bar
sbüt
tel,
Ger
man
y 03
/201
0
3.3.3 Lamella separator
Suspension refers to a mixture of substances
made up of a liquid containing finely distributed
solids. After passing through the precipitation and floccu-
lation steps, the raw water has been converted
into a suspension. This suspension passes into
the lamella separator (11).Fig. 3.8 shows the layout of the lamella separa-
tor (11), Fig. 3.9 its function.The lamella separator (11) separates the sus-
pension into treated water and sludge. The
treated water flows freely through the outlet into
the treated water tank (26). The sludge contains
the solids formed. Separation occurs because of
sedimentation of the specific heavier solids.
Thus, the solids sink downwards in the lamella
separator. Therefore, the sludge extraction is
located at the bottom and the outlet at the top. The height of the outlet determines the level in the
lamella separator.The lamella separator contains individual
lamellae, which take the form of inclined panels.
They increase the effective sedimentation area.
The lamellae fill the entire width of the lamella
separator and are combined into a lamella bun-
dle. The flow in the lamella separator is deter-
mined by the lamella bundle.Fig. 3.10, Page 22 shows the lamella bundle. It
is designed to be removable. This allows the
lamella bundle to be cleaned at the end of the
experiment.
Fig. 3.8 Lamella separator (11), layout
Fig. 3.9 Lamella separator (11), function
Lamella bundleLamella
Sludge extraction
Inle
t
Out
let
Sludge
Sus
pens
ion
Tre
ated
wat
er
La precipitación y floculación es un proceso físico/químico del tratamiento de aguas. Una aplicación importante de este proceso es la eliminación de metales disueltos, que suele ser necesaria para la producción de agua potable y el tratamiento de aguas subterráneas contaminadas.
Con CE 586 se puede enseñar este proceso de forma práctica.
Educación práctico Formación práctica en el tratamiento de aguas proceso físico/Una aplicación eliminación de necesaria para el as
e
rmación práctica en el tratamiento de aguas
E
Q
E
Q
T
F
Precipitación de sustancias disueltas
Unidad de alimentaciónBanco de ensayos
Formación de flóculos por coagulación y floculación
Un empleado de la British University Egipto (Cairo) explica el funciona-miento de CE 586.
Separación de los flóculos por sedimentación
1 2 3
En la página 77 encontrará un interesante vídeo en DVD del CE 586.
Department of Civil Engineering
TRATAMIENTO DE AGUAS PROCESOS FÍSICO / QUÍMICOS