Catalogo de Chavetas Paralelas
-
Upload
rafael-molina -
Category
Documents
-
view
219 -
download
0
Transcript of Catalogo de Chavetas Paralelas
-
8/18/2019 Catalogo de Chavetas Paralelas
1/8
KEYSTEEL - HERKEY
-
8/18/2019 Catalogo de Chavetas Paralelas
2/8
© Copyright Hercus 2008.While every care has been taken to ensure the accuracy of information contained in this data sheet, but no liability can be accepted for errors or omissions
All trademarks, registered names and logos belong to their respective companies
2
Phone: 08 8346 5522 Fax: 08 8346 5811 e-mail: hercus hercus.com.au Website: www.hercus.com.au
F.W. Hercus Pty. Ltd.12 Camira Street
Regency ParkSouth Australia, 5010
HERCUS PRODUCTS
12 Camira Street
Regency Park
South Australia, 5010
Phone 08 8346 5522
Fax 08 8346 5811
e-mail [email protected]
website www.hercus.com.au
-
8/18/2019 Catalogo de Chavetas Paralelas
3/8
© Copyright Hercus 2008.While every care has been taken to ensure the accuracy of information contained in this data sheet, but no liability can be accepted for errors or omissions
All trademarks, registered names and logos belong to their respective companies
3
Phone: 08 8346 5522 Fax: 08 8346 5811 e-mail: hercus hercus.com.au Website: www.hercus.com.au
F.W. Hercus Pty. Ltd.12 Camira Street
Regency ParkSouth Australia, 5010
A
C
D
B
NOMINAL DIAM.
CORNER RADIUS 'R'
E
F
Rl
KEYSTEEL - KEYWAY STANDARDS
IMPERIAL(BS 46 : PART 1 : 1958)
Safe working loads on keys.
Torque inch/pounds = 9000 x λ x F x shaft dia(inches)
Torque(inch/pounds) x RPM
HP = ————————————63025
Square Keys:
NOMINAL SHAFTDIAM.
DIMENSIONS (INCHES)
OVER TO(Incl.)
KEYSIZE
A B C D E F R
1/4” 1/2” 1/8” x 1/8”0.1240.125
0.0720.078
0.1250.126
0.0600.066
0.1270.125
0.010
1/2” 3/4” 3/16” x 3/16”0.1870.188
0.1070.113
0.1880.189
0.0880.094
0.1900.188
0.010
3/4” 1” 1/4” x 1/4”0.2490.250
0.1420.148
0.2500.251
0.1150.121
0.2520.250
0.010
1” 1.1/4” 5/16” x 5/16”0.3110.312
0.1770.183
0.3120.313
0.1420.148
0.3140.312
0.010
1.1/4” 1.1/2” 3/8” x 3/8” 0.3740.375
0.2130.219
0.3750.376
0.1690.175
0.3770.375
0.010
1.1/2” 1.3/4” 7/16” x 7/16”0.4370.438
0.2480.254
0.4380.439
0.1970.203
0.4400.438
0.020
1.3/4” 2” 1/2” x 1/2”0.4990.500
0.2830.289
0.5000.501
0.2240.230
0.5020.500
0.020
* 2” 2.1/4” 9/16” x 9/16”0.5620.563
0.3210.327
0.5630.564
0.2450.251
0.5650.563
0.020
2” 2.1/2” 5/8” x 5/8”0.6240.625
0.3540.360
0.6250.626
0.2780.284
0.6270.625
0.020
2.1/2” 3” 3/4” x 3/4”0.7490.750
0.4240.430
0.7500.751
0.3330.339
0.7520.750
0.020
3” 3.1/2” 7/8” x 7/8”0.8740.875
0.4950.501
0.8750.876
0.3870.393
0.8770.875
0.062
3.1/2” 4” 1” x 1”0.999
1.000
0.566
0.572
1.000
1.001
0.442
0.448
1.003
1.0000.062
* 4” 4.1/2” 1.1/8” x 1.1/8”1.1231.125
0.6400.646
1.1251.127
0.4890.495
1.1281.125
0.062
4” 5” 1.1/4” x 1.1/4”1.2481.250
0.7070.713
1.2501.252
0.5510.557
1.2531.250
0.062
* 5” 5.1/2” 1.3/8” x 1.3/8”1.3731.375
0.7820.788
1.3751.377
0.5980.604
1.3781.375
0.062
5” 6” 1.1/2” x 1.1/2”1.4981.500
0.8480.854
1.5001.502
0.6610.667
1.5041.500
0.062
* 6.1/2” 7” 1.3/4” x 1.3/4”1.7481.750
0.9930.999
1.7501.752
0.7620.768
1.7541.750
0.062
* 7.1/2” 8” 2” x 2”1.9982.000
1.1341.140
2.0002.002
0.8720.878
2.0042.000
0.062
* :- Indicates Non Standard Key.
-
8/18/2019 Catalogo de Chavetas Paralelas
4/8
© Copyright Hercus 2008.While every care has been taken to ensure the accuracy of information contained in this data sheet, but no liability can be accepted for errors or omissions
All trademarks, registered names and logos belong to their respective companies
4
Phone: 08 8346 5522 Fax: 08 8346 5811 e-mail: hercus hercus.com.au Website: www.hercus.com.au
F.W. Hercus Pty. Ltd.12 Camira Street
Regency ParkSouth Australia, 5010
A
C
D
B
NOMINAL DIAM.
CORNER RADIUS 'R'
E
F
Rl
KEYSTEEL - KEYWAY STANDARDS
IMPERIAL
(BS.46 : PART 1 : 1958)
Safe working loads on keys.
Torque inch/pounds = 9000 x λ x F x shaft dia(inches)
Torque(inch/pounds) x RPM
HP = ————————————63025
Rectangular Keys:
NOMINAL SHAFTDIAM.
DIMENSIONS (INCHES)
OVER TO(Incl.)
KEYSIZE
A B C D E F R
1” 1.1/4” 5/16” x 1/4”0.3110.312
0.1460.152
0.3120.313
0.1120.118
0.3140.312
0.2530.250
0.010
1.1/4” 1.1/2” 3/8” x 1/4”0.3740.375
0.1500.156
0.3750.376
0.1080.114
0.3770.375
0.2530.250
0.010
* 3/8” x 5/16”0.3740.375
0.1820.188
0.3750.376
0.1390.145
0.3770.375
0.3150.312
0.010
* 7/16” x 1/4”0.4370.438
0.1540.160
0.4380.439
0.1040.110
0.4400.438
0.2530.250
0.020
1.1/2” 1.3/4” 7/16” x 5/16”0.4370.438
0.1860.192
0.4380.439
0.1350.141
0.4400.438
0.3150.312
0.020
1.3/4” 2” 1/2” x 5/16”
0.499
0.500
0.190
0.196
0.500
0.501
0.131
0.137
0.502
0.500
0.315
0.312 0.020
* 1/2” x 7/16”0.4990.500
0.2560.262
0.5000.501
0.1890.195
0.5020.500
0.4400.438
0.020
2” 2.1/2” 5/8” x 7/16”0.6240.625
0.2600.266
0.6250.626
0.1850.191
0.6270.625
0.4410.438
0.020
* 5/8” x 1/2”0.6240.625
0.2950.301
0.6250.626
0.2130.219
0.6270.625
0.5020.500
0.020
2.1/2” 3” 3/4” x 1/2”0.7490.750
0.2990.305
0.7500.751
0.2090.215
0.7520.750
0.5030.500
0.020
* 3/4” x 5/8”0.7490.750
0.3660.372
0.7500.751
0.2740.280
0.7520.750
0.6290.625
0.020
3” 3.1/2” 7/8” x 5/8”0.8740.875
0.3700.376
0.8750.876
0.2640.270
0.8770.875
0.6290.625
0.062
* 1” x 5/8”0.9991.000
0.3740.380
1.0001.001
0.2600.266
1.0031.000
0.6290.625
0.062
3.1/2” 4” 1” x 3/4”0.9991.000
0.4410.447
1.0001.001
0.3180.324
1.0031.000
0.7540.750
0.062
4” 5” 1.1/4” x 7/8”1.2481.250
0.5180.524
1.2501.251
0.3660.372
1.2531.250
0.8790.875
0.062
5” 6” 1.1/2” x 1”1.4981.500
0.5990.605
1.5001.501
0.4120.418
1.5041.500
1.0061.000
0.062
* :- Indicates Non Standard Key.
-
8/18/2019 Catalogo de Chavetas Paralelas
5/8
© Copyright Hercus 2008.While every care has been taken to ensure the accuracy of information contained in this data sheet, but no liability can be accepted for errors or omissions
All trademarks, registered names and logos belong to their respective companies
5
Phone: 08 8346 5522 Fax: 08 8346 5811 e-mail: hercus hercus.com.au Website: www.hercus.com.au
F.W. Hercus Pty. Ltd.12 Camira Street
Regency ParkSouth Australia, 5010
A
C
D
B
NOMINAL DIAM.
CORNER RADIUS 'R'
E
F
Rl
KEYSTEEL - KEYWAY STANDARDS
METRIC (Normal)
(BS.4235 : PART 1 : 1972)
Safe working loads on keys.
Torque Nm = 0.065 x λ x F x shaft dia (mm)
Torque(Nm) x RPM
kW = —————————9550
NOMINAL SHAFT
DIAM.DIMENSIONS (mm)
OVER TO(Incl.)
KEYSIZE
A B C D E F R
10 12 4 x 43.9704.000
2.52.6
3.9854.015
1.81.9
4.0303.970
0.16
12 17 5 x 54.9705.000
3.03.1
4.9855.015
2.32.4
5.0304.970
0.25
17 22 6 x 65.9706.000
3.53.6
5.9856.015
2.82.9
6.0305.970
0.25
* 8 x 87.9648.000
5.05.2
7.9828.018
3.33.5
8.0007.970
0.25
* 10 x 109.96410.000
6.06.2
9.98210.018
4.34.5
10.0009.964
0.40
* 12 x 1211.95712.000
7.57.7
11.97912.021
4.95.1
12.00011.957
0.40
* 16 x 1615.95716.000
10.010.2
15.97916.021
6.46.6
16.00015.957
0.40
* 20 x 2019.94820.000
12.012.3
19.97420.026
8.48.7
20.00019.957
0.60
* 22 x 2221.94822.000
13.013.3
21.97422.026
9.49.7
22.00021.948
0.60
22 30 8 x 77.9648.000
4.04.2
7.9828.018
3.33.5
8.0007.964
7.0006.910
0.25
30 38 10 x 89.96410.000
5.05.2
9.98210.018
3.33.5
10.0009.964
8.0007.910
0.40
38 44 12 x 811.95712.000
5.05.2
11.97912.021
3.33.5
12.00011.957
8.0007.910
0.40
* 12 x 1011.95712.000
6.06.2
11.97912.021
4.34.5
12.00011.957
10.0009.964
0.40
44 50 14 x 9 13.95714.000 5.55.7 13.97914.021 3.84.0 14.00013.957 9.0008.910 0.40
50 58 16 x 1015.95716.000
6.06.2
15.97916.021
4.34.5
16.00015.957
10.0009.910
0.40
58 65 18 x 1117.95718.000
7.07.2
17.97918.021
4.44.6
18.00017.957
11.00010.890
0.40
65 75 20 x 1219.94820.000
7.57.7
19.97420.026
4.95.1
20.00019.948
12.00011.890
0.60
75 85 22 x 1421.94822.000
9.09.2
21.97422.026
5.45.6
22.00021.948
14.00013.890
0.60
• :- Indicates Non Standard Key.
-
8/18/2019 Catalogo de Chavetas Paralelas
6/8
© Copyright Hercus 2008.While every care has been taken to ensure the accuracy of information contained in this data sheet, but no liability can be accepted for errors or omissions
All trademarks, registered names and logos belong to their respective companies
6
Phone: 08 8346 5522 Fax: 08 8346 5811 e-mail: hercus hercus.com.au Website: www.hercus.com.au
F.W. Hercus Pty. Ltd.12 Camira Street
Regency ParkSouth Australia, 5010
KEYSTEEL - KEYWAY STANDARDS
NOMINAL SHAFTDIAM.
DIMENSIONS (mm)
OVER TO(Incl.)
KEYSIZE
A B C D E F R
85 95 25 x 1424.94825.000
9.09.2
24.97425.026
5.45.6
25.00024.948
14.00013.890
0.60
95 110 28 x 1627.94828.000
10.010.2
27.97428.026
6.46.6
28.00027.948
16.00015.890
0.60
110 130 32 x 1831.93832.000
11.011.2
31.96932.031
7.47.6
32.00031.938
18.00017.890
0.60
130 150 36 x 2035.93836.000
12.012.3
35.96936.031
8.48.7
36.00035.938
20.00019.870
1.00
150 170 40 x 2239.93840.000
13.013.3
39.96940.031
9.49.7
40.00039.938
22.00021.870 1.00
170 200 45 x 2544.93845.000
15.015.3
44.96945.031
10.410.7
45.00044.938
25.00024.870
1.00
200 230 50 x 2849.93850.000
17.017.3
49.96950.031
11.411.7
50.00049.938
28.00027.870
1.00
* :- Indicates Non Standard Key.
-
8/18/2019 Catalogo de Chavetas Paralelas
7/8
© Copyright Hercus 2008.While every care has been taken to ensure the accuracy of information contained in this data sheet, but no liability can be accepted for errors or omissions
All trademarks, registered names and logos belong to their respective companies
7
Phone: 08 8346 5522 Fax: 08 8346 5811 e-mail: hercus hercus.com.au Website: www.hercus.com.au
F.W. Hercus Pty. Ltd.12 Camira Street
Regency ParkSouth Australia, 5010
KEYSTEEL - TOLERANCES
HERKEY – BRIGHT DRAWN CARBON KEY STOCK SUITABLE FOR THE MANUFACTURE OF KEYS TO THE FOLLOWING
STANDARDS:-IMPERIAL - BS 46 : PART 1 : 1958METRIC - BS 4235 : PART 1 : 1972
STRENGTH U.T.S. – 35 to 45 TONS/SQ.INCH (540 to 700 MPa)ELONGATION - 12% MIN.MATERIAL - EN6 (0.40 Max. Carbon – 0.5 to 0.9 Manganese)STOCKED IN LENGTHS UP TO 3.2 Metres.
IMPERIAL (Inches) IMPERIAL (Inches)
Tolerance -0.000” Tolerance -0.000”Cat. No. Size
Width ThicknessCat. No. Size
Width Thickness
ATK009 1/16” x 1/16” + 0.0020 + 0.0020 * ATK203 7/16” x 5/16” + 0.0025 + 0.0025 *
ATK100 3/32” x 3/32” + 0.0020 + 0.0020 * ATK332 7/16” x 3/8” + 0.0025 + 0.0025
ATK101 1/8” x 1/8” + 0.0020 + 0.0020 ATK306 1/2” x 3/16” + 0.0025 + 0.0025 *
ATK219 5/32” x 5/32” + 0.0025 + 0.0020 * ATK307 1/2” x 1/4” + 0.0025 + 0.0025 *
ATK102 3/16” x 3/16” + 0.0025 + 0.0025 ATK204 1/2” x 5/16” + 0.0025 + 0.0025
ATK220 7/32” x 7/32” + 0.0025 + 0.0025 * ATK310 1/2” x 3/8” + 0.0025 + 0.0025 *
ATK103 1/4” x 1/4” + 0.0025 + 0.0025 ATK215 1/2” x 7/16” + 0.0025 + 0.0025
ATK221 9/32” x 9/32” + 0.0025 + 0.0025 * ATK308 9/16” x 5/16” + 0.0025 + 0.0025 *
ATK104 5/16” x 5/16” + 0.0025 + 0.0025 ATK314 9/16” x 1/2” + 0.0025 + 0.0025 *
ATK222 11/32” x 11/32” + 0.0025 + 0.0025 * ATK309 5/8” x 5/16” + 0.0025 + 0.0025 *
ATK105 3/8” x 3/8” + 0.0025 + 0.0025 ATK311 5/8” x 3/8” + 0.0025 + 0.0025 *
ATK106 7/16” x 7/16” + 0.0025 + 0.0025 ATK205 5/8” x 7/16” + 0.0025 + 0.0025
ATK107 1/2” x 1/2” + 0.0025 + 0.0025 ATK216 5/8” x 1/2” + 0.0025 + 0.0025
ATK108 9/16” x 9/16” + 0.0025 + 0.0025 ATK317 5/8” x 9/16” + 0.0025 + 0.0025 *
ATK109 5/8” x 5/8” + 0.0025 + 0.0025 ATK312 3/4” x 3/8” + 0.0025 + 0.0025 *
ATK223 11/16” x 11/16” + 0.0025 + 0.0025 * ATK313 3/4” x 7/16” + 0.0025 + 0.0025 * ATK110 3/4” x 3/4” + 0.0025 + 0.0025 ATK206 3/4” x 1/2” + 0.0025 + 0.0025
ATK224 13/16” x 13/16” + 0.0025 + 0.0025 * ATK217 3/4” x 5/8” + 0.0025 + 0.0025
ATK111 7/8” x 7/8” + 0.0025 + 0.0025 ATK322 3/4” x 11/16” + 0.0025 + 0.0025 *
ATK225 15/16” x 15/16” + 0.0030 + 0.0030 * ATK315 11/16” x 1/2” + 0.0025 + 0.0025 *
ATK112 1” x 1” + 0.0030 + 0.0030 ATK320 11/16” x 5/8” + 0.0025 + 0.0025 *
ATK116 1.1/8” x 1.1/8” + 0.0030 + 0.0030 ATK316 7/8” x 1/2” + 0.0025 + 0.0025 *
ATK227 1.3/16” x 1.3/16” + 0.0030 + 0.0030 * ATK207 7/8” x 5/8” + 0.0025 + 0.0025
ATK113 1.1/4” x 1.1/4” + 0.0030 + 0.0030 ATK323 7/8” x 11/16” + 0.0025 + 0.0025 *
ATK118 1.3/8” x 1.3/8” + 0.0030 + 0.0030 ATK325 7/8” x 3/4” + 0.0025 + 0.0025 *
ATK114 1.1/2” x 1.1/2” + 0.0040 + 0.0040 ATK218 1” x 5/8” + 0.0030 + 0.0025
ATK119 1.5/8” x 1.5/8” + 0.0040 + 0.0040 * ATK318 1” x 9/16” + 0.0030 + 0.0025 *
ATK115 1.3/4” x 1.3/4” + 0.0040 + 0.0040 ATK324 1” x 11/16” + 0.0030 + 0.0025 *
ATK228 1.7/8” x 1.7/8” + 0.0040 + 0.0040 * ATK208 1” x 3/4” + 0.0030 + 0.0025
ATK117 2” x 2” + 0.0040 + 0.0040 ATK329 1” x 7/8” + 0.0030 + 0.0025 *
ATK326 1.1/8” x 3/4” + 0.0030 + 0.0025 *
ATK300 3/32” x 1/8” + 0.0020 + 0.0020 * ATK330 1.1/8” x 7/8” + 0.0030 + 0.0025 *
ATK301 3/16” x 1/8” + 0.0025 + 0.0020 * ATK319 1.1/4” x 9/16” + 0.0030 + 0.0025 *
ATK302 1/4” x 1/8” + 0.0025 + 0.0020 * ATK321 1.1/4” x 5/8” + 0.0030 + 0.0025 *
ATK303 1/4” x 3/16” + 0.0025 + 0.0025 * ATK327 1.1/4” x 3/4” + 0.0030 + 0.0025 *
ATK304 5/16” x 3/16” + 0.0025 + 0.0025 * ATK209 1.1/4” x 7/8” + 0.0030 + 0.0025
ATK201 5/16” x 1/4” + 0.0025 + 0.0025 ATK331 1.1/4” x 1” + 0.0030 + 0.0030 *
ATK305 3/8” x 3/16” + 0.0025 + 0.0025 * ATK328 1.1/2” x 3/4” + 0.0040 + 0.0025 *
ATK202 3/8” x 1/4” + 0.0025 + 0.0025 ATK210 1.1/2” x 1” + 0.0040 + 0.0030
ATK213 3/8” x 5/16” + 0.0025 + 0.0025 ATK211 2.1/4" x 1.1/2" + 0.0040 + 0.0040 *
ATK214 7/16” x 1/4” + 0.0025 + 0.0025 * ATK212 2.3/4" x 1.7/8" + 0.0040 + 0.0040 *
-
8/18/2019 Catalogo de Chavetas Paralelas
8/8
© Copyright Hercus 2008.While every care has been taken to ensure the accuracy of information contained in this data sheet, but no liability can be accepted for errors or omissions
All trademarks, registered names and logos belong to their respective companies
8
Phone: 08 8346 5522 Fax: 08 8346 5811 e-mail: hercus hercus.com.au Website: www.hercus.com.au
F.W. Hercus Pty. Ltd.12 Camira Street
Regency ParkSouth Australia, 5010
KEYSTEEL - TOLERANCES
HERKEY – BRIGHT DRAWN CARBON KEY STOCK SUITABLE FOR THE MANUFACTURE OF KEYS TO THE FOLLOWINGSTANDARDS:-
IMPERIAL - BS 46 : PART 1 : 1958METRIC - BS 4235 : PART 1 : 1972
STRENGTH U.T.S. – 35 to 45 TONS/SQ.INCH (540 to 700 MPa)ELONGATION - 12% MIN.MATERIAL - EN6 (0.40 Max. Carbon – 0.5 to 0.9 Manganese)STOCKED IN LENGTHS UP TO 3.2 Metres.
METRIC (mm) METRIC (mm)
Tolerance +0.000mm Tolerance +0.000mmCat. No. Size
Width ThicknessCat. No. Size
Width Thickness
ATK501 4mm x 4mm -0.030 -0.030 ATK617 12mm x 10mm -0.043 -0.090
ATK502 5mm x 5mm -0.030 -0.030 ATK628 14mm x 6mm -0.043 -0.090 *
ATK503 6mm x 6mm -0.030 -0.030 ATK604 14mm x 9mm -0.043 -0.090 ATK629 7mm x 7mm -0.030 -0.030 * ATK630 16mm x 7mm -0.043 -0.090 * ATK504 8mm x 8mm -0.030 -0.030 ATK605 16mm x 10mm -0.043 -0.090
ATK505 10mm x 10mm -0.036 -0.036 ATK631 18mm x 7mm -0.043 -0.090 * ATK506 12mm x 12mm -0.043 -0.043 ATK606 18mm x 11mm -0.043 -0.110
ATK621 14mm x 14mm -0.043 -0.043 * ATK632 20mm x 8mm -0.043 -0.090 * ATK507 16mm x 16mm -0.043 -0.043 ATK607 20mm x 12mm -0.043 -0.110
ATK625 18mm x 18mm -0.043 -0.043 * ATK633 22mm x 9mm -0.052 -0.090 * ATK616 20mm x 20mm -0.043 -0.043 ATK608 22mm x 14mm -0.052 -0.110
ATK508 22mm x 22mm -0.052 -0.052 ATK609 25mm x 14mm -0.052 -0.110
ATK509 25mm x 25mm -0.052 -0.052 * ATK600 25mm x 22mm -0.052 -0.110 * ATK610 28mm x 16mm -0.052 -0.110
ATK626 8mm x 5mm -0.030 -0.090 * ATK634 28mm x 25mm -0.052 -0.110 * ATK601 8mm x 7mm -0.030 -0.090 ATK611 32mm x 18mm -0.062 -0.110
ATK627 10mm x 6mm -0.036 -0.090 * ATK612 36mm x 20mm -0.062 -0.130
ATK602 10mm x 8mm -0.036 -0.090 ATK613 40mm x 22mm -0.062 -0.130
ATK618 12mm x 6mm -0.043 -0.090 * ATK614 45mm x 25mm -0.062 -0.130
ATK603 12mm x 8mm -0.043 -0.090 ATK615 50mm x 28mm -0.062 -0.130