Ball Valves F14 / F14Dkitzeurope.com/pdf/ball-valves_catalog_en_6.pdf · Ball Valves F14 / F14D DIN...

Ball Valves F14 / F14D

DIN Full Bore, Floa! ng Ball, 2-piece body

KITZ CORPORATION OF EUROPE S.A.

T h e r e l i a b l e b r a n d

2

Ball ValvesFloa! ng Ball design

Pressure - Temperature Ra� ngs 3

Class PN 16 Cast Iron Ball Valves (F14) 4

Class PN 10 - 16 - 25 - 40 Carbon Steel Ball Valves (F14D) 6

Class PN 10 - 16 - 25 - 40 Stainless Steel Ball Valves (F14D) 8

Actuator Moun� ng Pad dimensions (F14D) 10

Applicable standards 11

Contents

All products introduced in this cataloge are covered by ISO 9001 certification awarded KITZ Corporation of Europe, S.A.

KITZ Corpora� on of Europe, S.A., Barcelona Plant, SpainKITZ Corpora� on Headquarter, Chiba, Japan

Ball Valves, Floa� ng Ball Design

3

Pressure-Temperature Ra� ngs

The pressure-temperature ra� ngs of ball valves are determined, not only by valve shell materials, but more essen� ally by sealing materials, used for ball seats, gland packing and gaskets.

Sealing materials may be high molecule, or rubber, but the choice is limited by the characteris� cs of the service fl uid, working temperatures, working pressures, velocity of fl uid, and opera� onal frequency of valves.

As it is very diffi cult to predetermine the exact pressure-temperature ra� ng for all kind of fl uids under all imaginable condi� ons, we have prepared general ra� ng charts for non-shock

fl uid service here, based on our past experiences both in the fi eld and in our laboratory.

In case of extraordinary service condi� ons as men� oned below, contact KITZ Corpora� on of Europe or its distributors for technical advice:

1. Valves shall be le� fully closed for a long period of � me under high temperature or high diff eren� al pressure.

2. Valves shall be frequently operated under high temperature or high diff eren� al pressure.

3. Frequent change of line pressure or temperature.

Virgin PTFE is the standard seat material for F14 and F14D series KITZ ball valves. Specify PTFE + Graphite or PTFE

+ Stainless Steel , PTFE + Glass Filled, etc. when required.

F14D PN10 - 16 - 25 - 40 DN 15 ~ 300 Body Ra� ng: Pressure resistance limita� on for valve body

F14 PN10 - 16 DN 15 ~ 200


4

F14 - Class PN16 Cast Iron Ball Valves

Full port, Split body, Side entry design

Features

• An! sta! c device

• Blowout-proof stem

• High performance PTFE ball seats

• Standars: Design: EN ISO 17292 Thickness: ISO 7121

Flanges drilled: EN 1092 Flanges surfaces: EN 1092

Leak test: BS EN 12266-1 Class A & DIN 3230

Lengths : Distance between fl anges as per EN 558-1

DN ≤ 100 basic serie 14

DN ≥ 125 basic serie 15

Page 3 for Pressure-Temperature Ra! ngs

Page 5 for Construc! on and Materials

Features of PN16 F14 Un: mm

Class PN16Gear Operator

H P1 B A

Valve Size

(Dn)

100 - 300 282 71

125 - 300 282 71

150 - 300 282 71

200 303 400 340 86

Gear Opera! on Un: mm

Worm gear operators may be mounted on KITZ ball valves at your op! on for the smoothest valve opera! on. Electric or pneuma! c actuators are also op! onally available. Contact KITZ distributors for appropriate choice and sizing of valve actuators.

Valve Size

DNPort L X P H

Cv

(m³/h)

Torque

PN16

(N.m)

Weight

(Kg)

15 12.5 115 52 150 85 17 5 1,8

20 19 120 55 150 90 39 6 2,8

25 25 125 58 150 104 63 8 3,7

32 32 130 58 200 115 104 15 6,1

40 38 140 60 200 120 150 20 7,5

50 51 150 60 250 132 254 25 10,9

65 65 170 75 250 144 381 40 15

80 76 180 78 250 154 971 60 20

100 102 190 95 500 212 1560 120 29,7

125 111 325 162 500 214 2173 150 46,5

150 144 350 175 750 238 4046 250 73

200 190 400 200 - Gear opera! on 8787 500 146 (1)

1 Cv = 1,16 Kv

Valve OperatorDn 15 ∼ 150 : lever opera! onDn 100 ∼ 150 : op! onal gear box Dn 200 : gear box or lever (op! onal)(1) Gear box included


5

Construc� on and Materials

No. PartsStandard

PN 16

1 Body GG25

4 Body Connector GG25

5 An! sta! c Stem*1 ASTM A479 Type 316 / 410

6 Gland Ring ASTM A479 Type 316

7 Gland Flange Steel

8 Stop Pin Steel

9 Stop Plate Steel zinc plated

11 Gland Washer Blue Steel

12 Nut*5 DIN 267/3-8 blued

15 Elas! c Ring Steel

16 Gland bolt Steel

17 Bolt - Stud Bolt*5 DIN 267/3/4 C8.8/8 blued / zinc plated

18 Nut*5 DIN 267/3/4 C8.8/8 blued / zinc plated

21 Ball*2 ASTM A479 Type 316 / 1.4408 / CA15

22 Ball Seat PTFE

24 Body Seal*4 PTFE / 316L+Flexite®

25 Gland Packing*3 PTFE+C+Graphite / PTFE

26 Stem Seal*3 PTFE+C+Graphite / PTFE

30 Handle Steel coated

31 Handle head GGG40

32 Handle bar GGG40

33 Handle bar bolt Stainless Steel

34 Handle head bolt Stainless Steel

¡ Standard material confi gura� on can be applied to

sour service.

All part numbers are corresponding with those shown in valve assembly drawings.

*1 DN ≤ 50 : ASTM A479 Type 316

DN > 50 : ASTM A479 Type 410

*2 DN ≤ 32 : ASTM A479 Type 316

32 < DN ≤ 50 : DIN 1.4408

DN > 50 : ASTM A217/A743 Gr. CA15

DIN 1.4408 (Op! onal)

*3 DN ≤ 25 : PTFE+C+Graphite

DN > 25 : PTFE

*4 DN ≤ 25 : PTFE

DN > 25 : 316L+ Flexite®

*5 DN < 40 : DIN 267/3 C8.8 blued

DN = 40 : DIN 267/3/4 C8.8/8 zinc plated

DN > 40 : DIN 267/3 C8.8 blued

DN ≤ 25

Valve fi nish : phosphate and oil dipped.

Opera� on group: DN ≤ 150 : by lever. (100 ~150 op! on: gear box)

DN = 200 : by gear box or with lever (Op! onal)


6

F14D - Class PN 10 - 16 - 25 - 40 Carbon Steel Ball Valves


Features




• Actuator moun! ng pad to ISO 5211

• Standars: Design: EN 1983:2006 Thickness: EN 12516-1


Dimensions of PN 10 -16 - 25 - 40 F14D Un: mm

Class DN PNGear Operator

H P1 B A

Valve Size

(Dn)

100

16-40

- 300 282 71

125 - 300 282 71

150 - 300 282 71

200 342 400 340 86

25010-16 378 400 340 86

25-40 378 500 365 130

300 10-40 440 500 365 130



Leak test: BS EN 12266-1 Class A & DIN 3230 FSM: BS 6755 P2

Lengths: Distance between fl anges as per EN 558-1

DN ≤ 100 basic serie 14 (Short)

DN ≥ 125 basic serie 15 (Short) - Serie 1 (Long)



Page 10 for Dimension of Actuator Moun! ng Pad

*1 PN 25-40:

Ball Bore=95

X= 85

H=190

*2 PN 25-40:

P=750

*3 PN 25-40:

H=396

*4 Gear Box

included

Valve Size

DNPort L X P H

ISO

5211

Cv

(m³/h)

Torque

(N.m)

Weight

(Kg)

PN10-16 PN25-40

Short Long PN16 PN40 Short Long Short Long

15 14 115 130 50 150 85 F03 17 5 8 2,6 2,8 2,6 2,8

20 19 120 150 52 150 90 F03 39 6 8 3,3 3,6 3,3 3,6

25 25 125 160 55 150 104 F05 63 8 10 4,3 4,5 4,3 4,5

32 32 130 180 58 200 116 F05 104 15 20 6,5 6,7 6,5 6,7

40 38 140 200 60 200 118 F05 150 20 25 7,8 7,9 7,8 7,9

50 51 150 230 60 250 128 F07 254 25 35 11,9 12,5 11,9 12,5

65 65 170 290 75 250 138 F07 381 40 50 15 16,1 15,5 16,5

80 76 180 310 78 250 148 F07 971 60 90 20 22,5 21 23

100 (1) 102 190 350 95 500 196 F10 1560 120 175 33 39,6 34,5 40,2

125 (2) 111 325 400 162.5 500 199 F10 2173 150 220 46 - 47 -

150 144 350 480 175 750 223 F10 4046 250 350 73 80 75,5 85

200 190 400 - 200 - Gear opera! on F14 8787 500 750 175 (4) - 185 (4) -

250 (3) 241 450 - 225 - Gear opera! on F14 14452 1000 1400 230 (4) - 250 (4) -

300 285 500 - 250 - Gear opera! on F16 22893 1500 2000 305 (4) - 370 (4) -

1 Cv = 1,16 Kv

Valve Operator

Dn 15 ∼ 150 : lever opera! onDn 100 ∼ 150 : op! onal gear box

Dn 200 : gear box or lever (op! onal)


7


No. PartsStandard

PN 10 - 16 - 25 - 40

1 Body DIN 1.0619

4 Body Connector DIN 1.0619

5 An� sta� c Stem*1 ASTM A479 Type 316 / 410


8 Stop Pin Steel

9 Stop Plate Steel zinc plated

11 Gland Washer Steel zinc plated

12 Nut DIN 267/3-8 blued

17 Stud Bolt-Bolt DIN 267/3/4 C 8.8/8 / zinc plated

18 Nut DIN 267/3/4 C 8.8/8 / zinc plated

21 Ball*2 ASTM A479 Type 316/CA15 / DIN 1.4408

22 Ball Seat PTFE

24 Body Seal*4 PTFE / 316L+ Flexite®



30 Handle Steel coated


32 Handle bar GGG40


35 Bolt Steel

36 Washer Steel

40 Stem O’ring FKM


sour service.


*1 DN ≤ 50 : ASTM A479 Type 316

50 < DN < 250 : ASTM A479 Type 410

DN ≥ 250 : ASTM A479 Type 316

*2 DN ≤ 50 : ASTM A479 Type 316

50 < DN < 250 : ASTM A217/A743 Gr. CA15

DIN 1.4408 (Op� onal)

DN ≥ 250 : DIN 1.4408


DN > 25 : PTFE

Cod. FSM : Graphite (Op� onal)

*4 DN ≤ 25 : PTFE


Cod. FSM : 316L+Graphite (Op� onal)


DN > 25 : PTFE

DN ≤ 25

Valve fi nish : phosphate and oil dipped.

Opera� on group : DN ≤ 150: by lever. (100 ~150 op� on: gear box)

DN = 200: by gear box or with lever (Op� onal)

DN > 200: by gear box.


8

F14D - Class PN 10 - 16 - 25 - 40 Stainless Steel Ball Valves


Dimensions of PN 10-16 - 25 - 40 F14D Un: mm

Class DN PNGear Operator

H P1 B A

Valve Size

(Dn)

100

16-40

- 300 282 71

125 - 300 282 71

150 - 300 282 71

200 342 400 340 86

25010-16 378 400 340 86

25-40 378 500 365 130

300 10-40 440 500 365 130



*1 PN 25-40:

Ball Bore=95

X= 85

H=190

*2 PN 25-40:

P=750

*3 PN 25-40:

H=396

*4 Gear Box

included

1 Cv = 1,16 Kv

Valve Size

DNPort L X P H

ISO

5211

Cv

(m³/h)

Torque

(N.m)

Weight

(Kg)

PN10-16 PN25-40

Short Long PN16 PN40 Short Long Short Long

15 14 115 130 50 150 85 F03 17 5 8 2,6 2,8 2,6 2,8

20 19 120 150 52 150 90 F03 39 6 8 3,3 3,6 3,3 3,6

25 25 125 160 55 150 104 F05 63 8 10 4,3 4,5 4,3 4,5

32 32 130 180 58 200 116 F05 104 15 20 6,5 6,7 6,5 6,7

40 38 140 200 60 200 118 F05 150 20 25 7,8 7,9 7,8 7,9

50 51 150 230 60 250 128 F07 254 25 35 11,9 12,5 11,9 12,5

65 65 170 290 75 250 138 F07 381 40 50 15 16,1 15,5 16,5

80 76 180 310 78 250 148 F07 971 60 90 20 22,5 21 23

100 (1) 102 190 350 95 500 196 F10 1560 120 175 33 39,6 34,5 41

125 (2) 111 325 400 162.5 500 199 F10 2173 150 220 46 - 47 -

150 144 350 480 175 750 223 F10 4046 250 350 73 80 75,5 85

200 190 400 - 200 - Gear opera! on F14 8787 500 750 175 (4) - 185 (4) -

250 (3) 241 450 - 225 - Gear opera! on F14 14452 1000 1400 230 (4) - 250 (4) -

300 285 500 - 250 - Gear opera! on F16 22893 1500 2000 305 (4) - 370 (4) -

Valve Operator

Dn 15 ∼ 150 : lever opera! onDn 100 ∼ 150 : op! onal gear box

Dn 200 : gear box or lever (op! onal)

Features




• Actuator moun! ng pad to ISO 5211

• Standars: Design: EN 1983:2006 Thickness: EN 12516-1


Leak test: BS EN 12266-1 Class A & DIN 3230 FSM: BS 6755 P2

Lengths: Distance between fl anges as per EN 558-1

DN ≤ 100 basic serie 14 (Short)

DN ≥ 125 basic serie 15 (Short) - Serie 1 (Long)



Page 10 for Dimension of Actuator Moun! ng Pad


9


No. PartsStandard

PN 10 - 16 - 25 - 40

1 Body DIN 1.4408

4 Body Connector DIN 1.4408

5 An� sta� c Stem ASTM A479 Type 316


8 Stop Pin DIN 267/11 A2-70

9 Stop Plate Steel nickel plated

11 Gland Washer DIN 1.4122 (SS)

12 Nut DIN 267/11 A2-70

17 Stud Bolt-Bolt*5 DIN 267/11/ A2-70 / 267/3 zinc plated

18 Nut*5 DIN 267/11/ A2-70 / 267/3 zinc plated

21 Ball*1 ASTM A479 Type 316 / 1.4408

22 Ball Seat PTFE

24 Body Seal*3 PTFE / 316L+Flexite®



30 Handle SS+Plas� c


32 Handle bar GGG40


35 Bolt Stainless Steel

36 Washer Stainless Steel

40 Stem O’ring FKM


sour service.


*1 DN ≤ 32 : ASTM A479 Type 316

DN > 32 : DIN 1.4408


DN > 25 : PTFE

Cod. FSM : Graphite (Op� onal)

*3 DN ≤ 25 : PTFE


Cod. FSM : 316L+Graphite (Op� onal)


DN > 25 : PTFE

*5 PN 10 - 16

DN ≤ 250 : DIN 267/11 A2-70

DN > 250 : DIN 267/3 C8.8 zinc plated

PN 25 - 40

DN ≤ 150 : DIN 267/11 A2-70

DN > 150 : DIN 267/3 C8.8 zinc plated

DN ≤ 25

Valve fi nish : (SS) Natural.

Opera� on group: DN ≤ 150: by lever. (100 ~150 op� on: gear box)

DN = 200: by gear box or with lever (Op� onal)

DN > 200: by gear box.


10

F14D - ISO 5211 Top Dimensions

for Class PN 10 - 16 - 25 - 40 Full Port, Split Body, Side Entry Design Ball Valves

F14D

Class

Nominal

size

(DN.)

-0.05

-0.10

G

-0.1

-0.2

ø E

-0.1

-0.2

ø S

± 0.2

ø J

B min. CL

(Short)

MF

ISO 5211

Flange

Typethread

PN

10-16

15 6 25 - 36 9.5 18 115 M5 1.5 F03

20 6 25 - 36 8 16.5 120 M5 1.5 F03

25 8 35 - 50 10 20.5 125 M6 2 F05

32 9 35 65 50 14.5 29 130 M6 2 F05

40 9 35 65 50 14.5 29 140 M6 2 F05

50 19 55 90 70 25.5 46 150 M8 3 F07

PN

25-40

65 19 55 90 70 25.5 46 170 M8 3 F07

80 19 55 90 70 25.5 46 180 M8 3 F07

100 22 70 125 102 40.5 66 190 M10 3 F10

125 22 70 125 102 40.5 66 325 M10 3 F10

150 22 70 125 102 40.5 66 350 M10 3 F10

200 30 GB14 ACT

100 175 140 42 GB145.5 ACT

64.5 GB148.5 ACT

400 M16 3 F14

250 30 GB14 ACT

100 175 140 42 GB145.5 ACT

64.5 GB148.5 ACT

450 M16 3 F14

300 18 130 210 165 171.5 174.50 500 M20 3 F16

Dimensions Un: mm

DN 200/250/300: Dimensions with Gear Box (GB) or Actuator (ACT)


11

Marking

BS 5351 / MSS-SP-25Coupling Flange

ISO 5211 / DIN 3337

Aplicable standards

Set-up Design Standard

BS 5351 / DIN 3357

Flanges

DIN 2501 / DIN 2526

Surface fi nish

MSS-SP-6 / DIN 2526

Quality Assurance

UNE-EN-ISO 9001

Face-to-Face distance

DIN 3202 F1 / F4 / F5

F1 : Long

F4 : ≤ DN100

F5 : ≥ DN125

Material Specifi ca� on

NACE MR 0175-2000

Tests

BS 6755 P.1 A / DIN 3230 P. 3

Fire Safe Standard

BS 6755 P. 2

Pressure-temperature ratings and other performance data published in this catalog have been

developed from our design calculation, in-house testing, fi eld reports provided by our customers

and/or published offi cial standards or specifi cations. They are good only to cover typical applications

as a general guideline to users of KITZ products introduced in this catalog.

For any specifi c application, users are kindly requested to contact KITZ Corporation of Europe for

technical advice, or to carry out their own study and evaluation for proving suitability of these

products to such an application. Failure to follow this request could result in property damage and/

or personal injury, for which we shall not be liable.

While this catalog has been compiled with the utmost care, we assume no responsibility for errors,

impropriety or inadequacy. Any information provided in this catalog is subject to from time-to-time

change without notice for error rectifi cation, product discontinuation, design modifi cation, new

product introduction or any other cause that KITZ Corporation of Europe considers necessary. This

edition cancels all previous issues.

CAUTION

Kitz Corporation of Europe S.A.

Ramón Viñas, 8

08930 Sant Adrià de Besòs

Barcelona

Spain - España

Ph. +34 93 462 14 08

Fax. +34 93 462 03 49

www.kitzeurope.com

EN-10-612-1

Ball Valves F14 / F14Dkitzeurope.com/pdf/ball-valves_catalog_en_6.pdf · Ball Valves F14 / F14D DIN...

Documents

Transcript of Ball Valves F14 / F14Dkitzeurope.com/pdf/ball-valves_catalog_en_6.pdf · Ball Valves F14 / F14D DIN...