7/27/2019 2001 Durango

1/2

Dodge Dur ango 2001

WWW.WIREMAGIC.COM

Wire/F unction Colour L ocation / Descr iptio Polar ity

Installation type: Remote start / security / GPS

Pink/black or Red Ignition harness +12 VOLTS

Dk.blue Ignition harness +IGNITION

Green/red (4.7L engine only) Ignition harness +IGNITION 2

Black/orange Ignition harness +ACCESSORY

Green Ignition harness +ACCESSORY 2

Yellow Ignition harness +STARTER

Black/gray At coil or PCM*` ACTACH

Orange/violet In driver's kickpanel** REV POLLOCK

Pink/violet In driver's kickpanel** REV POLUNLOCK

Yellow*** At courtesy light under dashpanel -DOORPIN

Tan/black 16 pin connector Below fuseblock -TRUNK PIN Tan/red In driver's kickpanel -DRIVER DOOR L ATCH

Lt.green/orange**** In driver's kickpanel -FACTORY ARM

Lt.green/orange**** In driver's kickpanel -FACTORY DISARM

White/tan At switch above brake pedal +BRAKESWITCH

Black/yellow At light switch harness +PARKLIGHTS

White/black At plug on handbrake lever -HAND BRAKE

Black/red At steering column -HORN

Lt.blue At main window switch REV POLDRIVER WINDOW UP

White At main window switch REV POLDRIVER WINDOW DOWN

Purple/white At main window switch REV POLPASSENGER WINDOW UP

Brown/white At main window switch REV POLPASSENGER WINDOW DOWN Dk.blue/white At main window switch REV POLLEFT REAR WINDOW UP

Red/black At main window switch REV POLLEFT REAR WINDOW DOWN

Gray/black At main window switch REV POLRIGHT REAR WINDOW UP

Green/white At main window switch REV POLRIGHT REAR WINDOW DOWN

Lt.green At light switch harness +HEADLIGHTS

Violet/black In driver's kickpanel +REVERSE LIGHTS

White/orange Pin-27 on C2 connector at PCM***** 8000ppmVSS WIRE

Lt.blue Ignition harness -KEY SENSE

PLEASE NOTE: This vehicle is equipped with a SENTRY-KEY IMMOBILIZER system. Please refer to the ALARM diagram beforeany remote start installation.* On the 5.9L the coil is located on the front of the engine, PCM is located in front of the Washer fluid reservoir. The 4.7Lengine has a coil for each cylinder. Use the TAN colored wire at any of the coils and set your remote starter for 1 cylinder.(see exploded views)** If equipped with keyless entry, these wires will be positive pulse. Models equipped with factory alarm have a single wire toperform all doorlock and security functions. See the DOORLOCK diagram.*** You can also find the doorpin wires on a BLACK plug on the left side of the brake pedal. BLACK/BLUE for the driver's door,TAN/RED for all the other doors and TAN/BLACK for the hatch. The factory alarm disarm LT.GREEN/ORANGE can also be foundon the plug.

Vehicle note:

Thursday, January 17, 2002 Page 1 of 2

Note: The information on this sheet is provided to you on an as is basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting toit. Only a computer safe logic probe or digital multimeter should be used. Wiremagic.com Corporation and/or any associated or unassociated individual or corporation who furnishes this document and/or software assumesabsolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in each and every case is the sole responsibility of the installer performing the work and

Wiremagic.com Corporation and/or any associated or unassociated individual or corporation assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly, or in an other wa . The information su lied is a uide onl . Co ri ht 1998-2001 Wirema ic.com Cor oration. All ri hts reserved.

7/27/2019 2001 Durango

2/2

Dodge Dur ango 2001

WWW.WIREMAGIC.COM

**** Use a ground pulse through a 1500-ohm resistor to disarm factory security (a second pulse will unlock the doors). Aground pulse through a 620-ohm resistor will arm security and lock the doors. The LT.GREEN/ORANGE is found in a BLACK

connector on the left side of the brake pedal.***** Located on the right front inner fender.

Thursday, January 17, 2002 Page 2 of 2

Note: The information on this sheet is provided to you on an as is basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting toit. Only a computer safe logic probe or digital multimeter should be used. Wiremagic.com Corporation and/or any associated or unassociated individual or corporation who furnishes this document and/or software assumesabsolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in each and every case is the sole responsibility of the installer performing the work and

Wiremagic.com Corporation and/or any associated or unassociated individual or corporation assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly, or in an other wa . The information su lied is a uide onl . Co ri ht 1998-2001 Wirema ic.com Cor oration. All ri hts reserved.