Post on 03-Apr-2018
7/28/2019 Actividad Comandos Switch
1/13
ACTIVIDAD COMANDOS SWITCH
1. Determinar cuntas interfaces tiene de fastEthernet y GigabitEthernet y nombre que
comienzan las interfaces.
>show running-config
7/28/2019 Actividad Comandos Switch
2/13
Los SWITCH Tiene 23 interfaces
fastEthernet Y 2 GigabitEthernet
7/28/2019 Actividad Comandos Switch
3/13
2. Crear 2 vlan, vlan 100(principal) y vlan 200(sucursal), adicione 2 puertos a cada una.
que vlan creadas, que puertos estn asociados a estas vlan que nombre tiene estas
vlan. (>show vlan)
-Switch principal
Observamos la configuracin
de la vlan 100(principal) con
dos puertos Fa 0/1, Fa 0/2
7/28/2019 Actividad Comandos Switch
4/13
-switch Sucursal
3. show flash(Que nombre tiene e indique las partes del archivo)
Switch principal
Observamos la configuracin de
la vlan 200(sucursal) con tres
puertos Fa 0/1, Fa 0/2, F0/3
Nombre del archivo
7/28/2019 Actividad Comandos Switch
5/13
Switch Sucursal
Nombre
de switch
VersinIOS
7/28/2019 Actividad Comandos Switch
6/13
4. Show versin
Muestra las caractersticas switch,puerto sw version
7/28/2019 Actividad Comandos Switch
7/13
5- show interface fastEthernet 0/3 y GigabitEthernet 1/1
Que ancho de banda tiene(BW)?
Determine si la interface es full dplex o half dplex?
Ancho de banda BW
La interface es Full Duplex
7/28/2019 Actividad Comandos Switch
8/13
5. Show mac-address-table
Ancho de banda BW
Interface es full Duplex
Se observa 1 direccin mac
7/28/2019 Actividad Comandos Switch
9/13
6. Uso de describe de interfacesSwitch principal utiliza las siguientes interfaces
Se observa 1 direccin mac
7/28/2019 Actividad Comandos Switch
10/13
Switch sucursal Estas son las interfaces que utiliza.
7/28/2019 Actividad Comandos Switch
11/13
7/28/2019 Actividad Comandos Switch
12/13
7. Configuracin ssh
Esta es el procedimiento para realizar la conexin remoto
8. Switch(config)#enable secret cisco9. Switch(config)#interface vlan2
10.%LINK-5-CHANGED: Interface Vlan2, changed state to up
11.12. %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to up13. Switch(config-if)#ip address 192.168.1.12 255.255.255.014. Switch(config-if)#exit15. Switch(config)#line vty 0 1516. Switch(config-line)#password cisco17. Switch(config-line)#login18. Switch(config-line)#end19. Switch#20. %SYS-5-CONFIG_I: Configured from console by console21.22. Switch#configure terminal23. Configuring from terminal, memory, or network [terminal]?24. Enter configuration commands, one per line. End with CNTL/Z.25. Switch(config)#ip domain-name26. Switch(config)#ip domain-namekathe.com27. Switch(config)#crypto key generate rsa28. The name for the keys will be:kathe.com29. Choose the size of the key modulus in the range of 360 to 2048 for your30. General Purpose Keys. Choosing a key modulus greater than 512 may take31. a few minutes.32.33.
How many bits in the modulus [512]: 1024
34. % Generating 1024 bit RSA keys, keys will be non-exportable...[OK]35.36. Switch(config)#ip ssh version 237. Switch(config)#line v38. Switch(config)#line vty 0 1539. Switch(config-line)#tr40. Switch(config-line)#transport input ssh41. Switch(config-line)#end42. Switch#43. %SYS-5-CONFIG_I: Configured from console by console44. copy running-config startup-config45. Destination filename [startup-config]?46. Building configuration...47. [OK]
http://jqar.com/http://jqar.com/http://jqar.com/http://switch.jqar.com/http://switch.jqar.com/http://switch.jqar.com/http://switch.jqar.com/http://jqar.com/7/28/2019 Actividad Comandos Switch
13/13
Esta pantalla nos indica la configuracin realizada